TMThomas Modes

Thomas Modes

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Thomas Modes has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Homogeneity of nanoparticle layers as deposited by gas phase condensation and co-deposited with PECVD processes

    by H. Nizard, S. Rauer, D. Gloess, A. Delan, T. Modes, T. Zubkova, M. Wolf, J. Neidhardt, A. Žukauskaitė, G. Gerlach, et al.

  • Open Access

    Anodic vacuum arc evaporation of graphite for depositing layers of tetrahedral amorphous carbon

    by Bert Scheffel, Olaf Zywitzki, Stefan Saager, Thomas Modes, Ludwig Decker, Robert Werberger

    Anodic vacuum arc evaporation was applied to deposit ta-C layers with thicknesses of 1.3–2.2 μm at high deposition rates of up to 18 nm/s. Building on prior work that was limited to a thickness of 0.8 μm due to high heat flux and adhesion issues, substrates with a high heat capacity and adhesion-promoting interlayers were used. Nanoindentation tests revealed hardness values ranging from 71 to 84 GPa and Young’s moduli ranging from 717 to 862 GPa for these layers. Raman spectrometry revealed an sp3 content of 68% to 75%. The layers are free of arc-typical droplets and have a very smooth surface. These results demonstrate that anodic vacuum arc evaporation, when combined with targeted thermal management and interlayer design, provides a scalable method of producing ta-C coatings for challenging mechanical or chemical engineering applications.


  • Open Access

    Homogeneity of matrix and nanocomposite layers as deposited by gas phase condensation (GPC) and PECVD processes

    by H. Nizard, A. Sytchkova, J. Yang, D. Gloess, U. Hartung, A. Delan, T. Modes, J. Neidhardt, A. Žukauskaitė, G. Gerlach, et al.


  • Open Access

    Formation of configurable uniform CdSeTe thin films by close-space sublimation deposition of multiple alternating CdSe and CdTe layers

    by Pascal Jundt, Olaf Zywitzki, Thomas Modes, Sagar Baitule, Robert Arndt, Bettina Späth, Bastian Siepchen

    Incorporation of selenium within cadmium telluride to form the CdSexTe1-x alloy has enabled higher device efficiencies in photovoltaic applications through improved passivation and current collection. Recent investigations of this alloy have simultaneously indicated significant potential for further performance gains as well as potentially serious detrimental characteristics. Exploring how best to utilize this important material requires consistent, configurable film deposition. Absorber layers are often deposited by close-space sublimation, which can produce high-quality films at large scale. It has previously been demonstrated that close-space sublimation of CdSeTe material directly is inconvenient and inflexible; therefore, an alternative method with greater consistency and control over film composition is sought. In this work, CdSeTe films were formed by close-space sublimation of alternating CdSe and CdTe layers followed by a high-temperature annealing in the presence of CdCl2. Under the optimal deposition conditions, this technique was shown to produce high-quality films of CdSeTe with homogeneous elemental distribution, uniform grain size, and low roughness. However, this method also exhibited a significant tendency to form numerous voids which largely persist after CdCl2 annealing. The source of this porosity was investigated and determined to primarily be resublimation of CdTe during the higher-temperature deposition of the CdSe layers. The process window to prevent voiding was observed to be rather small; while this would be a significant detriment in a production setting, it is less important in the targeted application for this approach, which is fundamental material and device investigations.

  • Open Access

    HOMOGENEITY OF MATRIX AND NANOCOMPOSITE LAYERS AS DEPOSITED BY GAS PHASE CONDENSATION (GPC) AND PE-CVD PROCESSES

    by Harry Nizard, Anna Sytchkova, Jiye Yang, Daniel Gloess, Ullrich Hartung, Annekatrin Delan, Thomas Modes, Jörg Neidhardt, Agne Žukauskaitė, Gerald Gerlach, et al.

    A vacuum deposition process for nanocomposite coatings, designed using a combination of inert gas phase condensation (GPC) and plasma-enhanced chemical vapor deposition (PE-CVD) processes, was demonstrated. Metal nanoparticles (NPs) were synthesized through the condensation of sputtered atomic vapor produced by gas flow sputtering (GFS). A low-pressure PE-CVD source was used for the direct encapsulation of the NPs inside plasma polymer layers obtained from organic precursors. Samples were transferred directly between NP and matrix sources, achieving safe-by-design in vacuo fixation of NPs inside multilayer nano-composite coatings. PE-CVD layers were investigated by Fourier-transform infrared (FTIR) spectroscopy. Then, PE-CVD combined with NPs multilayer nanocomposite coatings were investigated by cross-section scanning electron microscopy (SEM), variable angle UV-NIR ellipsometry and UV-Vis spectrometry. We observed typical localized surface plasmon resonance (LSPR) absorption peaks in the UV-Vis spectra and a redshift with increasing particle size, as well as a broadening of absorption peaks with increasing Ag content, confirming the plasmonic activity of deposited nanocomposite thin films required for optical and sensor applications.