A. A. Belyaev
A. A. Belyaev has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Alexander S. Evtushenko
Povolzhskiy State University of Telecommunications and Informatics
1 shared publication - Anton Vladimirovich Bourdine
Department of Communication Lines, Povolzhskiy State University of Telecommunications and Informatics, Samara, Russia
1 shared publication - D. N. Shurupov
JSC “Scientific Production Association State Optical Institute Named After Vavilov S.I.
1 shared publication - E. V. Ter-Nersesyants
JSC “Scientific Production Association State Optical Institute Named After Vavilov S.I.
1 shared publication - Elena S. Zaitseva
Department of Communication Lines, Povolzhskiy State University of Telecommunications and Informatics, 23, Lev Tolstoy Street, Samara 443010, Russia
1 shared publication - Grigorii S. Polishchuk
JSC "Research and Production Corporation S.I. Vavilova" 192171 Saint Petersburg Russian Federation
1 shared publication
Latest Publications
- Open Access
- 25 February 2026
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 26 (1) , 1-14
Research of parameters of fusion splices of telecommunication multimode optical fibers and silica microstructured fiber lightguides with hexagonal configuration
This work presents the results of experimental approbation of the ability to fuse telecommunication graded index multimode optical fibers of ISO/IEC Category OM2+/OM3 and silica microstructured optical fibers by using a commercially available field fusion splicer kit Fujikura-36S (Fujikura Ltd., Japan). We tested silica microstructured optical fiber with a hexagonal configuration that provides quasi-singlemode operation over an extended spectral band up to short wavelengths (λ = 800–1700 nm) in comparison with conventional singlemode optical fiber of ratified ITU-T Recommendations. The potential possibilities were explored for reducing of attenuation by selection and combination of fusion program parameters (arc current and arc time) to find a compromise between quality fusion splicing without any defects and minimization of insertion loss. About 1.5 m long short segment of researched microstructured optical fiber was spliced between two spools with multimode fibers, while each one of them was also spliced with two pigtailed spools with singlemode optical fibers. Fiber length of each spool was at the least 1 km long in order to provide insertion loss measurements by using optical time domain reflectometer EXFO AXS-110 (EXFO, Canad a). Based on a series of experiment, we have identified an optimal combination of arc current (STD-30 a.u.) and arc time (1100 ms) which provides desired compromise between reducing the fusion program parameters to prevent the MOF air hole collapsing under the quality splice without defects, and decreased insertion loss. As a result, the total insertion loss has been reduced to 0.8–1.0 dB and more in comparison with the reference value. For instance, mentioned above program settings gave the loss 5.721 dB under the reference value 6.722 dB. Therefore, the experimental results confirm ability of fusion splicing microstructured and multimode optical fibers with an acceptable insertion loss by using commercially available field fusion splicer kits. This provides to utilize proposed microstructured optical fibers with extended singlemode operation wavelength range in various applications of laser technology, optical devices and short-range high bit rate optical networks.
- 25 February 2026
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 26 (1) , 1-14
Open AccessResearch of parameters of fusion splices of telecommunication multimode optical fibers and silica microstructured fiber lightguides with hexagonal configuration
This work presents the results of experimental approbation of the ability to fuse telecommunication graded index multimode optical fibers of ISO/IEC Category OM2+/OM3 and silica microstructured optical fibers by using a commercially available field fusion splicer kit Fujikura-36S (Fujikura Ltd., Japan). We tested silica microstructured optical fiber with a hexagonal configuration that provides quasi-singlemode operation over an extended spectral band up to short wavelengths (λ = 800–1700 nm) in comparison with conventional singlemode optical fiber of ratified ITU-T Recommendations. The potential possibilities were explored for reducing of attenuation by selection and combination of fusion program parameters (arc current and arc time) to find a compromise between quality fusion splicing without any defects and minimization of insertion loss. About 1.5 m long short segment of researched microstructured optical fiber was spliced between two spools with multimode fibers, while each one of them was also spliced with two pigtailed spools with singlemode optical fibers. Fiber length of each spool was at the least 1 km long in order to provide insertion loss measurements by using optical time domain reflectometer EXFO AXS-110 (EXFO, Canad a). Based on a series of experiment, we have identified an optimal combination of arc current (STD-30 a.u.) and arc time (1100 ms) which provides desired compromise between reducing the fusion program parameters to prevent the MOF air hole collapsing under the quality splice without defects, and decreased insertion loss. As a result, the total insertion loss has been reduced to 0.8–1.0 dB and more in comparison with the reference value. For instance, mentioned above program settings gave the loss 5.721 dB under the reference value 6.722 dB. Therefore, the experimental results confirm ability of fusion splicing microstructured and multimode optical fibers with an acceptable insertion loss by using commercially available field fusion splicer kits. This provides to utilize proposed microstructured optical fibers with extended singlemode operation wavelength range in various applications of laser technology, optical devices and short-range high bit rate optical networks.