INIlyas Nurakhmetov

Ilyas Nurakhmetov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ilyas Nurakhmetov has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Defining the design and operating parameters for an energy-efficient unit for continuous microwave treatment of sunflower kernels prior to pressing in order to produce sunflower oil

    by Akzhol Suleimen, Baurzhan Nurakhmetov, Ardak Askarov, Ilyas Nurakhmetov

    This study explores a powdered core strip for arc surfacing of complex doped alloy and composite alloys. The task addressed is to determine conditions for uniform melting of the shell and core. The conditions under which, during surfacing, the uneven heating of the shell and core at powdered core strip extension is reduced have been determined. When surfacing composite alloys, this achieves the dosed mass transfer of refractory metal carbides into the weld pool in their initial state and their required volumetric concentration. When surfacing complex doped alloyed alloys, the spillage of the charge components into the core is eliminated, bypassing the drop stage. This achieves chemical homogeneity of the weld metal. Analytical descriptions of the thermal state of the core in the thermal field of the welding current have been substantiated and compiled. Their dependence on the deposition modes, the design of the electrode, the thermophysical characteristics of the core, as well as the duration of the thermal effect, have been established. Thus, with an increase in the charge temperature from 100 to 700°C, the thermal conductivity decreases by 1.3–1.5 times. It has been shown that the intensity of heating the core is determined by the ratio of the intensity of two effects – heat transfer through the boundary layer and heat transfer by the core material. Their quantitative accuracy makes it possible to estimate the redistribution of heat in the core volume, the probability of thermal transformation of the charge ingredients, and local changes in the aggregate state. The results reveal general patterns of heat transfer. Examples with graphical support to the practical implementation of modeling are given, which have shown reasonable reliability for engineering calculations. The established patterns could be used in practice for the processes of restoring parts by arc surfacing methods

  • Open Access

    Development of a statistical model for walnut shelling in a reciprocating millstone unit

    by Baurzhan Temov, Baurzhan Nurakhmetov, Ardak Askarov, Ilyas Nurakhmetov, Galymzhan Nasrullin

    The object of this study is the process of walnut shelling in a reciprocating millstone, implementing combined compression, shear, and torsion loading. The problem being addressed is the lack of well-founded modes that simultaneously ensure complete shell destruction and a high yield of whole kernels—two conflicting requirements in processing. This study extends previous work that determined the shell fracture forces and the probabilistic nature of its failure; this work transitions from the strength characteristics of the object to machine performance. A three-factor rotatable design of a central composite experiment (Box design) consisting of twenty trials was implemented. The factors included the angular velocity of the moving upper millstone (1.38–4.90 rad/s), the number of nut revolutions in the working channel (0.33–1.17 revolutions), and the roughness pitch of the working surfaces (7.95–18.05 mm). Two responses were recorded: shell fracture rate and whole kernel yield. Second-order regression models were obtained and tested using analysis of variance. It was found that shell fracture rate increases with increasing angular velocity and rotational speed and decreases with increasing roughness pitch, while whole kernel yield decreases with increasing angular velocity and exhibits internal maxima at rotational speed and roughness pitch. Angular velocity is the dominant factor for both responses and serves as the main source of the tradeoff between cracking and kernel integrity. A compromise regime was identified: angular velocity of approximately 2.09 rad/s, approximately 1.0 nut revolution, and a roughness pitch of approximately 10 mm, resulting in a shell fracture rate of approximately 94.5% with a whole kernel yield of approximately 88.9%. The results serve as a basis for selecting walnut shelling machine parameters

  • Open Access

    Identifying patterns of walnut shell fracture under combined loading in a reciprocating millstone system

    by Baurzhan Temov, Baurzhan Nurakhmetov, Ardak Askarov, Ilyas Nurakhmetov, Galymzhan Nasrullin

    This study explores the process of shell fracture in a locally cultivated walnut variety in a reciprocating millstone setup that implements combined compression, shear, and torsion loading. The task addressed is to enable cracking across the entire shell surface while maintaining kernel integrity, which determines the yield of marketable produce. In the first stage, shell fracture forces were experimentally determined under localized loading from a natural cleft and a whole shell, followed by statistical processing using a two-parameter Weibull distribution. It was found that fracture from the cleft side occurs at lower loads than from the whole shell side, confirming the anisotropy of the shell's mechanical properties. In the second stage, the effect of roughness pitches of 10, 13, and 16 mm on the fracture force was studied. Experiments have shown that at a 10 mm pitch, fracture occurs with the lowest force; increasing the pitch to 13 and 16 mm increases the fracture force due to a decrease in local stress concentration. A comparison of the two experimental stages revealed that the geometry of the working surfaces determines the conditions for fracture without changing the general pattern: when loading from a natural cleft, lower forces are required. For a fracture probability of at least 0.95 for any nut orientation, a load of approximately 350 N is required. Additionally, the strength characteristics of the kernel were determined using an ST-2 structure analyzer; the average fracture force under direct loading is approximately 1200 grams (≈ 120 N). The results provide a mechanically sound basis for selecting the parameters of the working parts of a nut cracking machine and a safe range of operating loads

  • Open Access

    Development of an effective method of microwave treatment of sunflower kernel to increase oil extraction

    by Akzhol Suleimen, Baurzhan Nurakhmetov, Ardak Askarov, Yevgeniy Medvedkov, Ilyas Nurakhmetov

    The study focused on microwave processing of sunflower seeds and a unit for its implementation during the preparation stage for mechanical pressing. This unit intensifies the destruction of the kernel's cellular structure, increases oil yield, and maintains its quality within acceptable limits. The aim was to increase the extraction of high-quality sunflower oil. The design features of a pilot unit for microwave seed processing and the optimal parameters for microwave seed processing were determined. It was established that maximum oil extraction without degrading its quality is achieved by using a gentle microwave processing mode, which prevents overheating, changes in the structure and chemical composition of the kernel, and increased oxidation processes. The unit was applied at a power of 500 watts for 150 seconds with a 42 mm layer of peeled sunflower seeds. With these values, the oil yield was approximately 57.4%. Uniform grain distribution within the processed layer was achieved by using a guide spiral and a rotating horizontal disk, which ensures uniform movement and height of the moving layer. A distinctive feature of the obtained results is the use of a microwave processing unit consisting of a guide spiral, a rotating horizontal disk, and an experimental methodology using second-order rotatable planning to determine the relationship between oil yield and microwave power, duration, and seed layer thickness on the rotating disk surface. These results can be scaled up for use in industrial vegetable oil production facilities for domestic consumption and increased potential exports