Thomas Pejot
Research Subjects
Thomas Pejot has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Alexis Deschamps
SIMaP, University of Grenoble Alpes, CNRS, Grenoble INP, Grenoble, France
3 shared publications - Frédéric De Geuser
Université Grenoble Alpes, CNRS, Grenoble INP, SIMaP, F-38000 Grenoble, France
3 shared publications Julien Barlier
3 shared publications- Thomas Perrin
SIMaP Grenoble, 1130, Rue de la Piscine, 38402 Saint-Martin d’Hères, France
2 shared publications Isabelle Mouton
1 shared publication
Latest Publications
- Open Access
- 10 July 2026
- Published by Elsevier in Materials & Design
- Vol. 269
High-throughput characterization of the effect of quenching rate and dispersoid type on precipitation kinetics in two Al-Zn-Mg-Cu alloys
- 10 July 2026
- Published by Elsevier in Materials & Design
- Vol. 269
Open AccessHigh-throughput characterization of the effect of quenching rate and dispersoid type on precipitation kinetics in two Al-Zn-Mg-Cu alloys
- Open Access
- 5 May 2026
- Published by Elsevier in SSRN Electronic Journal
High-throughput characterization of the effect of quenching rate and dispersoid type on precipitation kinetics in two Al-Zn-Mg-Cu alloys
A high-throughput investigation has been conducted on two Al–Zn–Mg–Cu alloys with a different dispersoid population (Cr or Zr based) to study the influence of quenching rate on precipitation kinetics. We developed a modified Jominy specimen to vary the quench rate down to 1 K.s-1. Across the obtained continuous range of quench rates, microstructure was evaluated using space and time-resolved small-angle X-ray scattering (SAXS), allowing to map the post-quench precipitation kinetics as a function of quench rate. Transmission electron microscopy revealed that Cr-containing dispersoids systematically trigger heterogeneous η-phase precipitation, while Zr-containing dispersoids remain inactive unless recrystallization induces loss of coherency. A critical cooling rate of 30 K.s-1 has been identified from the SAXS data, below which large precipitation-free zones develop and the volume fraction of strengthening precipitates decreases. These quench-induced precipitates modify the precipitation kinetics during ageing, both in terms of volume fraction, average size and precipitate size distribution. The resulting loss of hardness scales at first order with the square root of the precipitate volume fraction, indicating that the reduction in the fraction of homogeneous precipitates dominates over changes in size or spatial distribution.
- 5 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessHigh-throughput characterization of the effect of quenching rate and dispersoid type on precipitation kinetics in two Al-Zn-Mg-Cu alloys
A high-throughput investigation has been conducted on two Al–Zn–Mg–Cu alloys with a different dispersoid population (Cr or Zr based) to study the influence of quenching rate on precipitation kinetics. We developed a modified Jominy specimen to vary the quench rate down to 1 K.s-1. Across the obtained continuous range of quench rates, microstructure was evaluated using space and time-resolved small-angle X-ray scattering (SAXS), allowing to map the post-quench precipitation kinetics as a function of quench rate. Transmission electron microscopy revealed that Cr-containing dispersoids systematically trigger heterogeneous η-phase precipitation, while Zr-containing dispersoids remain inactive unless recrystallization induces loss of coherency. A critical cooling rate of 30 K.s-1 has been identified from the SAXS data, below which large precipitation-free zones develop and the volume fraction of strengthening precipitates decreases. These quench-induced precipitates modify the precipitation kinetics during ageing, both in terms of volume fraction, average size and precipitate size distribution. The resulting loss of hardness scales at first order with the square root of the precipitate volume fraction, indicating that the reduction in the fraction of homogeneous precipitates dominates over changes in size or spatial distribution.
- Open Access
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
Revealing time and size-dependent precipitate composition in an Al-Zn-Mg-Cu alloy using Atom Probe Tomography
High strength Al-Zn-Mg-Cu alloys gain their mechanical properties through a precipitation sequence involving GP zones, followed by the metastable ’ phase and the stable . During this sequence the composition of the nanometric precipitates evolves continuously, both in terms of solvent content and in terms if solute ratio between Zn, Mg and Cu. Understanding this evolution is a key for the development of predictive models, which do not consider to date explicitly the evolving composition. Moreover, within a given microstructure the precipitate composition may be size-dependent, which has not yet been studied in details. In the present study, Atom Probe Tomography (APT) was used to investigate an Al–Zn–Mg–Cu alloy subjected to ageing at 120°C and 175°C. A new, quantitative-based methodology was developed to determine the composition threshold for defining the precipitate boundaries. Along the ageing treatments, this procedure was applied to characterize the time and size dependence of precipitate composition. At 120°C, precipitates were found to contain a majority of Aluminum content and no detectable Copper, with no significant dependence on precipitate size. At 175°C, precipitates become richer in all solute elements. Particularly, Copper enrichment was observed, and this enrichment was found to be more pronounced for smaller particles. This size-dependent Cu composition of precipitates is believed to have strong implications on the coarsening resistance of the precipitates.
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessRevealing time and size-dependent precipitate composition in an Al-Zn-Mg-Cu alloy using Atom Probe Tomography
High strength Al-Zn-Mg-Cu alloys gain their mechanical properties through a precipitation sequence involving GP zones, followed by the metastable ’ phase and the stable . During this sequence the composition of the nanometric precipitates evolves continuously, both in terms of solvent content and in terms if solute ratio between Zn, Mg and Cu. Understanding this evolution is a key for the development of predictive models, which do not consider to date explicitly the evolving composition. Moreover, within a given microstructure the precipitate composition may be size-dependent, which has not yet been studied in details. In the present study, Atom Probe Tomography (APT) was used to investigate an Al–Zn–Mg–Cu alloy subjected to ageing at 120°C and 175°C. A new, quantitative-based methodology was developed to determine the composition threshold for defining the precipitate boundaries. Along the ageing treatments, this procedure was applied to characterize the time and size dependence of precipitate composition. At 120°C, precipitates were found to contain a majority of Aluminum content and no detectable Copper, with no significant dependence on precipitate size. At 175°C, precipitates become richer in all solute elements. Particularly, Copper enrichment was observed, and this enrichment was found to be more pronounced for smaller particles. This size-dependent Cu composition of precipitates is believed to have strong implications on the coarsening resistance of the precipitates.