Gangwei Mei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gangwei Mei has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Yongsheng He
Institute of Defense Engineering, AMS, PLA, Beijing 100036, China
2 shared publications - Chao Shen
Institute of Defense Engineering, AMS, PLA, Beijing 100036, China
1 shared publication - Chunhai Li
Defense Engineering Institute, AMS, PLA, Beijing 100036, China
1 shared publication - Jianguo Du
Institute of Defense Engineering, AMS, PLA, Beijing 100036, China
1 shared publication - Jun Shen
Institute of Defence Engineering, AMS, Beijing 100036, China
1 shared publication - Linmei Lyu
Institute of Defense Engineering, AMS, PLA, Beijing 100036, China
1 shared publication
Latest Publications
- Open Access
Full-Scale Blast Response of a Buried Reinforced-Concrete Box in Loess and Coral Sand: Contrasting Free-Field Attenuation and Localised Interface-Pressure Amplification
Comparative full-scale blast data for buried reinforced-concrete (RC) boxes in crushable coral sand remain scarce. Four lateral-detonation tests used the same instrumented box: three in loess (0.6, 1.0 and 2.0 kg TNT) and one in coral sand (1.0 kg). Apparent front velocities were 193–272 m/s for the retained loess pairs and 82–95 m/s in coral sand; an unresolved T3 timing outlier is reported separately. Loess peak free-field pressure followed P = 0.50·Z − 3.08 (P in MPa; Z inserted numerically in m·kg−1/3). For T1/T3 at Z ≈ 0.95, the peak-pressure and duration ratios were 1.045 and 1.35, whereas the impulse ratio was 1.055–1.094 rather than the theoretical 1.49; classical impulse similarity is therefore unsupported. At Z = 1.0, coral sand reduced the free-field peak by 54%, while facing-wall pressures of 1.30–1.34 MPa gave an apparent directional Kr ≈ 4. Facing-centre acceleration decreased from 258 to 26 g and velocity increased from 89 to 846 mm/s. A compaction–reflection interpretation using wall-synchronous values and a directional reference identifies Id ≈ 4.42 × 105 kg/(m2·s); Md ≈ 0.108 GPa additionally assumes ρd = 1800 kg/m3. This is single-test parameter identification, not independent validation. Because the box was reused and no quantitative crack or residual-deformation survey was available, the results demonstrate contrasting load/response signatures and motivate preliminary mechanisms, not general design coefficients or an observed failure-mode transition.
Open AccessFull-Scale Blast Response of a Buried Reinforced-Concrete Box in Loess and Coral Sand: Contrasting Free-Field Attenuation and Localised Interface-Pressure Amplification
Comparative full-scale blast data for buried reinforced-concrete (RC) boxes in crushable coral sand remain scarce. Four lateral-detonation tests used the same instrumented box: three in loess (0.6, 1.0 and 2.0 kg TNT) and one in coral sand (1.0 kg). Apparent front velocities were 193–272 m/s for the retained loess pairs and 82–95 m/s in coral sand; an unresolved T3 timing outlier is reported separately. Loess peak free-field pressure followed P = 0.50·Z − 3.08 (P in MPa; Z inserted numerically in m·kg−1/3). For T1/T3 at Z ≈ 0.95, the peak-pressure and duration ratios were 1.045 and 1.35, whereas the impulse ratio was 1.055–1.094 rather than the theoretical 1.49; classical impulse similarity is therefore unsupported. At Z = 1.0, coral sand reduced the free-field peak by 54%, while facing-wall pressures of 1.30–1.34 MPa gave an apparent directional Kr ≈ 4. Facing-centre acceleration decreased from 258 to 26 g and velocity increased from 89 to 846 mm/s. A compaction–reflection interpretation using wall-synchronous values and a directional reference identifies Id ≈ 4.42 × 105 kg/(m2·s); Md ≈ 0.108 GPa additionally assumes ρd = 1800 kg/m3. This is single-test parameter identification, not independent validation. Because the box was reused and no quantitative crack or residual-deformation survey was available, the results demonstrate contrasting load/response signatures and motivate preliminary mechanisms, not general design coefficients or an observed failure-mode transition.
- Open Access
Axial Hysteretic Mechanical Characteristics of Wire Rope Isolators and Parameter Identification with a Novel Algebraic Closed-Form Model
Wire rope isolators (WRIs) exhibit typical nonlinear and asymmetric hysteretic behavior, with their mechanical performance being significantly influenced by the coupled effects of multiple parameters. This study investigates the dynamic response of large-sized spiral WRIs under axial loading. Within the framework of an asymmetric hysteresis model, a novel algebraic closed-form formulation is adopted for parameter identification and numerical simulation. Furthermore, a characteristic parameter, A, is introduced to quantify the unique mechanical behavior induced by the structural configuration of WRIs. Five types of large-sized spiral WRIs are selected as test specimens. For each WRI, tests are conducted under 30 distinct working conditions, yielding a total of 150 cyclic loading tests across all scenarios. By systematically varying the displacement amplitude, loading frequency, and preloading pressure, the influences of these key parameters on the dynamic characteristics of WRIs are comprehensively analyzed. These characteristics encompass the axial hysteresis loop shape, energy dissipation capacity, equivalent viscous damping, and average secant stiffness. The results indicate that these three loading parameters exert substantial effects on the mechanical properties of large-sized WRIs. Additionally, the simulated hysteresis curves derived from the identified parameters exhibit excellent agreement with the experimental observations. Compared with conventional mechanical models, the proposed algebraic closed-form model demonstrates slightly higher fitting accuracy, thereby validating its effectiveness and applicability in characterizing the mechanical behavior of large-sized WRIs. This research provides a crucial reference for the engineering application of large-sized spiral WRIs and facilitates the broader adoption of the proposed modeling approach.
Open AccessAxial Hysteretic Mechanical Characteristics of Wire Rope Isolators and Parameter Identification with a Novel Algebraic Closed-Form Model
Wire rope isolators (WRIs) exhibit typical nonlinear and asymmetric hysteretic behavior, with their mechanical performance being significantly influenced by the coupled effects of multiple parameters. This study investigates the dynamic response of large-sized spiral WRIs under axial loading. Within the framework of an asymmetric hysteresis model, a novel algebraic closed-form formulation is adopted for parameter identification and numerical simulation. Furthermore, a characteristic parameter, A, is introduced to quantify the unique mechanical behavior induced by the structural configuration of WRIs. Five types of large-sized spiral WRIs are selected as test specimens. For each WRI, tests are conducted under 30 distinct working conditions, yielding a total of 150 cyclic loading tests across all scenarios. By systematically varying the displacement amplitude, loading frequency, and preloading pressure, the influences of these key parameters on the dynamic characteristics of WRIs are comprehensively analyzed. These characteristics encompass the axial hysteresis loop shape, energy dissipation capacity, equivalent viscous damping, and average secant stiffness. The results indicate that these three loading parameters exert substantial effects on the mechanical properties of large-sized WRIs. Additionally, the simulated hysteresis curves derived from the identified parameters exhibit excellent agreement with the experimental observations. Compared with conventional mechanical models, the proposed algebraic closed-form model demonstrates slightly higher fitting accuracy, thereby validating its effectiveness and applicability in characterizing the mechanical behavior of large-sized WRIs. This research provides a crucial reference for the engineering application of large-sized spiral WRIs and facilitates the broader adoption of the proposed modeling approach.