JSJun Shen

Jun Shen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jun Shen has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Analysis of the Delayed Instability Mechanism of Heterogeneous Fractured Rock Slopes Under Rainfall Infiltration

    by Yu Zhao, Jun Shen, Yunhou Sun, Xiaolong Wang, Feng Li

    Rainfall-induced delayed instability of fractured rock slopes is strongly affected by fracture preferential flow, hydro-mechanical coupling, and spatial matrix heterogeneity. However, the coupled influence of stress-dependent fracture aperture evolution and heterogeneous matrix properties on delayed slope deformation remains insufficiently quantified. In this study, a two-dimensional discrete fracture network (DFN)–equivalent continuum coupled model was established using spectral random field theory and a representative Monte Carlo-generated fracture geometry. The spectral exponent β = 1.0–2.5 was adopted to characterize different degrees of matrix heterogeneity, and rainfall infiltration–stress coupling simulations were conducted under an extreme rainfall scenario followed by drainage. The results indicate that the wetting front advances irregularly in the heterogeneous matrix, while fracture preferential flow accelerates rainwater infiltration and promotes local pore-pressure accumulation near the phreatic surface. After rainfall cessation, water stored in fractures continues to recharge the deep matrix, leading to delayed pore-pressure increase and post-rainfall deformation. The simulated fracture aperture shows an initial closure followed by gradual dilation, which is controlled by the competition between saturation-induced stress redistribution and pore-pressure-driven effective stress reduction. Under a common strength reduction factor of FOS = 1.4, stronger matrix heterogeneity results in more pronounced plastic strain concentration and larger displacement amplitude along the potential slip zone. These findings suggest that fracture aperture evolution and matrix heterogeneity jointly influence delayed deformation and potential failure-zone development in rainfall-affected fractured rock slopes. The conclusions should be interpreted within the scope of a two-dimensional DFN–equivalent continuum numerical framework with prescribed rainfall conditions and representative fracture/random-field realizations.


  • Open Access

    Study on the Dynamic Mechanical Properties of Deep-Seated Rocks Under Coupled Confining Pressure and Loading Rate

    by Xuhui Li, Yunhou Sun, Jun Shen, Zailin Yang, Yong Mei, Chenliang Li, Shengyi Cong

    Deep rock engineering faces the combined challenges of high in situ stress and dynamic disturbances. However, traditional constitutive models treat confining pressure and rate effects independently, leading to significant prediction errors under high confinement, and the underlying coupled mechanisms remain insufficiently understood. To address this, dynamic tests were conducted using an active confining pressure SHPB system under hydrostatic pressures of 0–30 MPa and loading rates of 2000–12,000 GPa·s−1, with simultaneous acoustic emission and dissipated energy monitoring. A confining pressure-sensitive rate-dependent dual-scalar damage constitutive model was established, innovatively incorporating a Constraint Intensification Factor (CIF) and a viscous regularization technique to intrinsically couple confinement and rate effects. The results reveal a synergistic strengthening effect between confining pressure and loading rate, with higher confining pressure enhancing rate sensitivity. The proposed model accurately captures the elastic, peak, and post-peak segments of stress–strain curves, with peak stress errors below 5%, effectively overcoming the prediction deficiencies of traditional models under high confining pressures. These findings provide critical parameters and a reliable theoretical basis for deep rock engineering design.


  • Open Access

    Axial Hysteretic Mechanical Characteristics of Wire Rope Isolators and Parameter Identification with a Novel Algebraic Closed-Form Model

    by Gangwei Mei, Yongsheng He, Mengnan Dai, Longyun Zhou, Xiongliang Yao, Jun Shen, Chunhai Li

    Wire rope isolators (WRIs) exhibit typical nonlinear and asymmetric hysteretic behavior, with their mechanical performance being significantly influenced by the coupled effects of multiple parameters. This study investigates the dynamic response of large-sized spiral WRIs under axial loading. Within the framework of an asymmetric hysteresis model, a novel algebraic closed-form formulation is adopted for parameter identification and numerical simulation. Furthermore, a characteristic parameter, A, is introduced to quantify the unique mechanical behavior induced by the structural configuration of WRIs. Five types of large-sized spiral WRIs are selected as test specimens. For each WRI, tests are conducted under 30 distinct working conditions, yielding a total of 150 cyclic loading tests across all scenarios. By systematically varying the displacement amplitude, loading frequency, and preloading pressure, the influences of these key parameters on the dynamic characteristics of WRIs are comprehensively analyzed. These characteristics encompass the axial hysteresis loop shape, energy dissipation capacity, equivalent viscous damping, and average secant stiffness. The results indicate that these three loading parameters exert substantial effects on the mechanical properties of large-sized WRIs. Additionally, the simulated hysteresis curves derived from the identified parameters exhibit excellent agreement with the experimental observations. Compared with conventional mechanical models, the proposed algebraic closed-form model demonstrates slightly higher fitting accuracy, thereby validating its effectiveness and applicability in characterizing the mechanical behavior of large-sized WRIs. This research provides a crucial reference for the engineering application of large-sized spiral WRIs and facilitates the broader adoption of the proposed modeling approach.