Imre Nagy-Gombai
Research Subjects
Research Interests
Imre Nagy-Gombai has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Gábor József Béres
John von Neumann University
2 shared publications - Gábor Kalácska
Hungarian University of Agriculture and Life Sciences
2 shared publications - Martin László Kölüs
Research Group of Mechanical- and Laser Beam Technologies, John von Neumann University, 6000 Kecskemét, Hungary
2 shared publications
Latest Publications
- Open Access
- 20 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 32
The Effect of Mesh Type and Meshing Strategy on the Finite Element Simulation of a Stack Compression Test
The stack compression test (SCT) represents an efficient method for characterizing the large deformation behavior of sheet metals and obtaining material parameters for finite element simulations. However, the experimental procedure is affected by several conditions that can lead to uncertainties, particularly regarding the friction conditions between individual specimen layers. Inverse modeling based on finite element simulations offers a potential solution; however, the complex deformation mechanisms within multilayer stacks frequently result in numerical instabilities. Preliminary investigations show that model parameterization strongly influences simulation accountability, while minor variations in friction coefficients may lead to numerical failure. Therefore, this study examines the effects of mesh type and meshing strategy to establish a stable and reliable computational framework for SCT simulations.
- 20 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 157 (1) , 32
Open AccessThe Effect of Mesh Type and Meshing Strategy on the Finite Element Simulation of a Stack Compression Test
The stack compression test (SCT) represents an efficient method for characterizing the large deformation behavior of sheet metals and obtaining material parameters for finite element simulations. However, the experimental procedure is affected by several conditions that can lead to uncertainties, particularly regarding the friction conditions between individual specimen layers. Inverse modeling based on finite element simulations offers a potential solution; however, the complex deformation mechanisms within multilayer stacks frequently result in numerical instabilities. Preliminary investigations show that model parameterization strongly influences simulation accountability, while minor variations in friction coefficients may lead to numerical failure. Therefore, this study examines the effects of mesh type and meshing strategy to establish a stable and reliable computational framework for SCT simulations.
- Open Access
- 17 April 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 390, 173-180
Investigation of Friction Coefficient at Stack Compression Tests
During sheet metal forming (for example, deep drawing), the desired geometry is typically produced under large plastic deformations. However, in order to characterize the material behavior in this deformation range as accurately as possible, experimental investigation of the material is indispensable. Such investigations are necessary, among other reasons, to determine material properties that may later serve as input parameters for finite element (FEM) simulations. By defining appropriate material properties, the design and optimization of the forming technology become more efficient. One such property is the material’s flow curve; for determining it in the large deformation range, a particularly promising method is the stack compression test (SCT). At the same time, the method also has certain drawbacks. One is that the test is not standardized, and therefore there is no exact methodology for its execution. Another difficulty arises from the fact that the friction conditions present during the test are not clearly defined. In this paper, we seek to determine whether the friction conditions in the case of the SCT can be inferred by a comparative analysis of experimental force–displacement curves and force–displacement curves obtained from FEM simulations.
- 17 April 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 390, 173-180
Open AccessInvestigation of Friction Coefficient at Stack Compression Tests
During sheet metal forming (for example, deep drawing), the desired geometry is typically produced under large plastic deformations. However, in order to characterize the material behavior in this deformation range as accurately as possible, experimental investigation of the material is indispensable. Such investigations are necessary, among other reasons, to determine material properties that may later serve as input parameters for finite element (FEM) simulations. By defining appropriate material properties, the design and optimization of the forming technology become more efficient. One such property is the material’s flow curve; for determining it in the large deformation range, a particularly promising method is the stack compression test (SCT). At the same time, the method also has certain drawbacks. One is that the test is not standardized, and therefore there is no exact methodology for its execution. Another difficulty arises from the fact that the friction conditions present during the test are not clearly defined. In this paper, we seek to determine whether the friction conditions in the case of the SCT can be inferred by a comparative analysis of experimental force–displacement curves and force–displacement curves obtained from FEM simulations.