MSMohammed H. Shukur

Mohammed H. Shukur

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mohammed H. Shukur has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Studying the Effect of Skew Angle on the Behavior of Concrete Slab Under Repeated Load

    by Mohammed H. Shukur, Oday A. Salih, Kaythar A. Ibrahim, Suhaib Y. K. Al-Darzi

    This study experimentally and numerically investigates how skew angle affects the structural behavior of reinforced concrete slabs under monotonic and repeated loading. Eight simply supported slab specimens were divided into four groups corresponding to skew angles of 0°, 15°, 30°, and 45°, with one specimen in each group tested under monotonic loading and the other under repeated loading. All specimens had plan dimensions of 1400 × 1400 mm and a thickness of 100 mm and were subjected to a concentrated load at mid-span. The repeated-loading protocol consisted of stepwise quasi-static loading–unloading cycles with the peak load increased by 5 kN in each successive cycle until failure. All specimens exhibited predominantly flexural failure, with major cracking concentrated within the middle region of the slabs. The first-cracking loads under repeated loading were approximately 9.1–12.0% lower than those of the corresponding monotonic specimens. The effect of repeated loading on yield and ultimate response depended on skew angle and did not exhibit a uniform trend. However, increasing skew angle generally reduced load resistance and increased deformation. Under repeated loading, the ultimate load decreased by approximately 13.2%, 27.6%, and 33.1% for skew angles of 15°, 30°, and 45°, respectively, relative to the zero-skew specimen. Under monotonic loading, the 45° specimen exhibited approximately 24.9% lower ultimate resistance than the zero-skew specimen. The displacement ductility response was non-monotonic; under monotonic loading, maximum ductility occurred at 30°, and under repeated loading, at 15°. A simplified equivalent-strip analytical model was used as a preliminary reference, while three-dimensional nonlinear finite-element models were developed using ANSYS. The finite-element predictions of ultimate load differed from the experimental results by approximately 5.6–15.2%, although larger differences were observed in the load–deflection response and crack distribution. Overall, the experimental findings suggest that skew angle and loading history may influence deformation, stiffness, and ultimate resistance. However, since only one specimen was tested for each configuration, the reported differences should be considered descriptive observations rather than statistically validated relationships. Further experimental investigations with replicate specimens are required to confirm these trends.

  • Open Access

    Structural Response of Thin-Web Beams to Various Web Opening Retrofit Techniques

    by Oday A. Salih, Kaythar A. Ibrahim, Mohammed H. Shukur, Suhaib Y. K. Al-Darzi, Sofyan Y. Ahmed

    Accidental web openings caused by impact, corrosion, or conflict-related damage can substantially reduce the strength, stiffness, and stability of steel bridge girders. Although numerous studies have examined beams containing intentionally designed web openings, limited experimental research has systematically compared practical rehabilitation methods for accidental openings in slender-web plate girders. This study experimentally and numerically evaluates several rehabilitation configurations incorporating welded patch plates and transverse stiffeners. Ten slender-web steel girder specimens, each 1800 mm long, 800 mm deep, and 300 mm wide, were tested under monotonic concentrated loading at mid-span. Nonlinear finite element models were also developed to qualitatively examine the principal deformation and instability trends. Relative to the control specimen, the untreated web opening reduced the ultimate load by approximately 43% and exhibited approximately 10% greater deflection at its respective ultimate load. One-sided and two-sided welded patch plates increased the ultimate load of the damaged specimen by approximately 22% and 26%, respectively. Transverse stiffeners increased the ultimate load by approximately 73% while exhibiting substantially lower ultimate-load deflections. The combined use of patch plates and transverse stiffeners provided the greatest improvement, increasing the ultimate load by approximately 101–123% relative to the untreated damaged specimen and substantially reducing lateral instability. The findings demonstrate that effective rehabilitation of slender-web girders requires not only restoration of the interrupted load path but also restraint of web instability.

  • Open Access

    Structural Response of Thin-Web Beams to Various Web Opening Retrofit Techniques

    by Oday Asal Salih, Kaythar A. Ibrahim, Mohammed H. Shukur, Suhaib Yahya Kasim Al-Darzi, Sofyan Younis Ahmed

    A novel retrofitting method was tested to open steel girder webs. As no standard covers these procedures, this study examined the effect of mid-span apertures on AISC-designed narrow I-beams. Ten specimens with 1.8m length, 0.8m height, and 0.3m flange width were examined, with four simulated in ANSYS to validate results and explore parametric effects (yield stress and web thickness). Openings lower strength by 43% and increase deflection by 10%. Two retrofitting options involve patch plates welded to one or both sides of the aperture. Patch plate retrofitting removes 8% deflection and restores 26% strength. As an alternate retrofitting option, adding two stiffeners to the opening sides increases strength by 73% and reduces deflections by 68%. Patches and stiffeners work best together, improving strength by 123% and lowering deflection by 89%. Testing the modified specimens demonstrated that patch plate welding to treat steel web openings works well. Instead of treating the opening, stiffeners on the side improve girder behaviour. Experimental and finite element analysis results match at different levels. Additionally, numerical stress findings provide a satisfactory estimate of beam element stress.