SASuhaib Yahya Kasim Al-Darzi

Suhaib Yahya Kasim Al-Darzi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Suhaib Yahya Kasim Al-Darzi has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Studying the Effect of Skew Angle on the Behavior of Concrete Slab Under Repeated Load

    by Mohammed H. Shukur, Oday A. Salih, Kaythar A. Ibrahim, Suhaib Y. K. Al-Darzi

    This study experimentally and numerically investigates how skew angle affects the structural behavior of reinforced concrete slabs under monotonic and repeated loading. Eight simply supported slab specimens were divided into four groups corresponding to skew angles of 0°, 15°, 30°, and 45°, with one specimen in each group tested under monotonic loading and the other under repeated loading. All specimens had plan dimensions of 1400 × 1400 mm and a thickness of 100 mm and were subjected to a concentrated load at mid-span. The repeated-loading protocol consisted of stepwise quasi-static loading–unloading cycles with the peak load increased by 5 kN in each successive cycle until failure. All specimens exhibited predominantly flexural failure, with major cracking concentrated within the middle region of the slabs. The first-cracking loads under repeated loading were approximately 9.1–12.0% lower than those of the corresponding monotonic specimens. The effect of repeated loading on yield and ultimate response depended on skew angle and did not exhibit a uniform trend. However, increasing skew angle generally reduced load resistance and increased deformation. Under repeated loading, the ultimate load decreased by approximately 13.2%, 27.6%, and 33.1% for skew angles of 15°, 30°, and 45°, respectively, relative to the zero-skew specimen. Under monotonic loading, the 45° specimen exhibited approximately 24.9% lower ultimate resistance than the zero-skew specimen. The displacement ductility response was non-monotonic; under monotonic loading, maximum ductility occurred at 30°, and under repeated loading, at 15°. A simplified equivalent-strip analytical model was used as a preliminary reference, while three-dimensional nonlinear finite-element models were developed using ANSYS. The finite-element predictions of ultimate load differed from the experimental results by approximately 5.6–15.2%, although larger differences were observed in the load–deflection response and crack distribution. Overall, the experimental findings suggest that skew angle and loading history may influence deformation, stiffness, and ultimate resistance. However, since only one specimen was tested for each configuration, the reported differences should be considered descriptive observations rather than statistically validated relationships. Further experimental investigations with replicate specimens are required to confirm these trends.

  • Open Access

    Structural Response of Thin-Web Beams to Various Web Opening Retrofit Techniques

    by Oday A. Salih, Kaythar A. Ibrahim, Mohammed H. Shukur, Suhaib Y. K. Al-Darzi, Sofyan Y. Ahmed

    Accidental web openings caused by impact, corrosion, or conflict-related damage can substantially reduce the strength, stiffness, and stability of steel bridge girders. Although numerous studies have examined beams containing intentionally designed web openings, limited experimental research has systematically compared practical rehabilitation methods for accidental openings in slender-web plate girders. This study experimentally and numerically evaluates several rehabilitation configurations incorporating welded patch plates and transverse stiffeners. Ten slender-web steel girder specimens, each 1800 mm long, 800 mm deep, and 300 mm wide, were tested under monotonic concentrated loading at mid-span. Nonlinear finite element models were also developed to qualitatively examine the principal deformation and instability trends. Relative to the control specimen, the untreated web opening reduced the ultimate load by approximately 43% and exhibited approximately 10% greater deflection at its respective ultimate load. One-sided and two-sided welded patch plates increased the ultimate load of the damaged specimen by approximately 22% and 26%, respectively. Transverse stiffeners increased the ultimate load by approximately 73% while exhibiting substantially lower ultimate-load deflections. The combined use of patch plates and transverse stiffeners provided the greatest improvement, increasing the ultimate load by approximately 101–123% relative to the untreated damaged specimen and substantially reducing lateral instability. The findings demonstrate that effective rehabilitation of slender-web girders requires not only restoration of the interrupted load path but also restraint of web instability.

  • Open Access

    Structural Response of Thin-Web Beams to Various Web Opening Retrofit Techniques

    by Oday Asal Salih, Kaythar A. Ibrahim, Mohammed H. Shukur, Suhaib Yahya Kasim Al-Darzi, Sofyan Younis Ahmed

    A novel retrofitting method was tested to open steel girder webs. As no standard covers these procedures, this study examined the effect of mid-span apertures on AISC-designed narrow I-beams. Ten specimens with 1.8m length, 0.8m height, and 0.3m flange width were examined, with four simulated in ANSYS to validate results and explore parametric effects (yield stress and web thickness). Openings lower strength by 43% and increase deflection by 10%. Two retrofitting options involve patch plates welded to one or both sides of the aperture. Patch plate retrofitting removes 8% deflection and restores 26% strength. As an alternate retrofitting option, adding two stiffeners to the opening sides increases strength by 73% and reduces deflections by 68%. Patches and stiffeners work best together, improving strength by 123% and lowering deflection by 89%. Testing the modified specimens demonstrated that patch plate welding to treat steel web openings works well. Instead of treating the opening, stiffeners on the side improve girder behaviour. Experimental and finite element analysis results match at different levels. Additionally, numerical stress findings provide a satisfactory estimate of beam element stress.

  • Open Access

    Studying the Effect of Skew Angle on the Behavior of Concrete Slab under Repeated Load

    by Mohammed H. Shukur, Oday Asal Salih, Kaythar A. Ibrahim, Suhaib Yahya Kasim Al-Darzi

    In the present work, an experimental investigation was conducted for 8 groups of skew slabs, with 0, 15, 30 and 45 skew angles, with one slab for each group under monotonic and repeated loads. The simple span slab specimens with dimensions of 1400x1400x100 mm, supported from two sides, were tested using concentrated loads at mid-span. The mode of failure for each slab investigated showed that flexural failure with cracks at the middle third appeared for all specimens. It was found that the first cracking loads decreased with the increase of skew angle and decreased when a repeated load was compared with a monotonic load with a larger deflection. The present work concluded that the yield and ultimate loads decreased by increasing the skew angle, and the deflection increased. It was also found that the repeated load causes a decrease in yield and an increase in deflection. The work includes calculations for the theoretical loads and deflection, and the results obtained for skew slabs are less than those experimentally obtained. The ductility index is estimated and shows that increasing the skew angle will increase the ductility of the slab. Additionally, the use of repeated loads decreases the ductility of the skew sl

  • Open Access

    Structural Behavior of Beam-Column Connection Using Post-Installed Steel and GFRP Rebars

    by Borkan M. Mutashar, Oday Asal Salih, Suhaib Y. Kasim

    This study investigates the performance of steel and GFRP bars as post-installed reinforcement for retrofitting concrete infrastructure through experimental evaluation of the structural performance of the beam-column connection specimens. Three groups of concrete specimens were tested under flexural loading to investigate the influence of bar diameter, bar material (Steel vs. GFRP), and installation method on failure modes, load-deflection curves, and bond strength. The main failure mode at the connections was concrete breakout; however, specimens reinforced with small-diameter post-installed bars tended to fail by bar pullout. The load capacity increases by 9.64% and 12.5% when the diameter of the post-installed GFRP bar increases from 12 to 16 mm and 20 mm, respectively, and the deflection at the midspan of the beam decreases by 17.9% and 33.6% for 16 and 20 mm bars. Specimens with cast-installed reinforcements showed comparable load capacity to post-installed specimens but exhibited lower displacements. Increasing bar diameter reduced bond strength, and GFRP bars showed lower bond strength than steel bars. Overall, the results highlight the potential of GFRP bars as reliable post-installed reinforcement for strengthening critical concrete connections.

  • Bubble Deck Slabs: An Innovative Structural System for Sustainable Construction - A Review

    by Ahmed A. Mohammed Ali, Suhaib Y. Al-Darzi

    The Bubble Deck slab is an innovative construction technique that incorporates spherical plastic voids inside concrete slabs to diminish self-weight while preserving structural integrity. This technology reduces the amount of material used by a significant amount by carefully replacing non-structural concrete with voids, which results in cost savings and improved sustainability. The production of bubble deck slabs, their design principles, benefits, drawbacks, and new developments in their use are all covered in this review study. Particular emphasis is placed on their role in modern construction, highlighting their environmental benefits, ease of installation, and structural performance compared to conventional solid slabs. Additionally, the study also highlights critical research areas, including the interaction between voids and reinforcement, the slab's behavior under static and dynamic loading conditions, and its contribution to sustainable building practices. Bubble Deck slabs help make concrete production more sustainable by minimizing the total carbon impact, improving load distribution, and decreasing construction waste. Even with these limitations, recent progress in material science and computational modeling has strengthened their potential as a sustainable and efficient substitute for standard reinforced concrete slabs. The use of Bubble Deck technology is an important advancement in the direction of structural systems that are more efficient in their use of resources and that perform better, as construction practices continue to develop toward more environmentally friendly solutions.

  • Open Access

    Evaluating the Efficacy of Shear Connectors in H Steel Sections Embedded in Concrete

    by Alaulddin Abdulrahman Al-Jafal, Suhaib Yahya Al-Darzi

    This study is focusing on H steel sections embedded in concrete by evaluating various shear connectors, including headed studs, bolts, steel angles, perfobonds, and self-connected variants. This comprehensive examination of nine specimens aims to understand their load-bearing capacity, failure mechanisms, and overall performance in structural composite connections. The paper thoroughly compares and analyzes the load-slip curves, average initial shear stiffness, ultimate load, ductility, and fracture energy for these connectors. The research highlights self-connected connectors with rebars passing through flanges demonstrating substantial increases in ultimate load (41 %) in comparison to natural bond only, and maintaining ductility post-peak. Moreover, through this study it has been found that when shear studs and shear angles are designed for equivalent loads exhibit remarkably similar performance. Additionally, adding extra connectors to the web of H-sections enhances load capacity and stiffness but reduces ductility. The double shear in 10 mm diameter 8.8 bolted (with two nuts inside and outside flange) connectors raise the ultimate load but shift the curve of load slip from ductile to brittle in comparison with the same diameter studs.

  • Open Access

    The Impact Load Behavior of Reinforced Concrete Slab Samples Containing Waste Plastic Aggregate

    by Suhaib Yahya Kasim Al-Darzi, Kaythar A. Ibrahim, Oday Asal Salih

    In the present study, eight reinforced concrete slabs divided into four groups with two slabs per group were fabricated and tested under impact load, replacing their aggregate with 0%, 4%, 8%, and 16% of polyethylene terephthalate) PET). During the preparation process, PET materials increased the workability of fresh concrete by up to 16% and decreased the density by 9%. The compressive strength decreased by about 11.7%, 15.7%, and 19.9% using 4%, 8%, and 16% of PET, respectively. Splitting strength decreased by 7.2%, 17.4%, and 20.3% using 4%, 8%, and 16% of PET, respectively. Failure mode and deflection amplitude results showed that PET delayed the first cracks and reduced the crack lengths and width and crack spreading at failure. Also, impact resistance enhanced at the first crack and ultimate load stages when PET was used compared to normal concrete. The maximal and minimal displacement decreased with increasing PET proportion to 8% and 16%. The slabs were modeled using the finite element program SAP2000 with 4-node shell elements. The finite element (FE) analysis showed a similar deflection response as those experimentally obtained for all slabs. The deflection obtained by FE was less, about 15.5% and 19%, compared with all slabs experimentally tested except slab G2-2, which showed a higher deflection of about 16.3%.


  • Open Access

    Experimental and numerical investigation on composite beam–column joint connection behavior using different types of connection schemes

    by Lawend Kamal Askar, Suhaib Yahya Kasim Al-Darzi, Bayar Jafar Mohamed Al-Sulayfani

    Over the past few decades, composite joints have been regarded as one of the most promising approaches. After reviewing the research articles dealing with composite beam-column joints, it can be withdrawn that few researchers studied and developed different types of composite beam-column joints. The objectives of this paper to study the effect and behavior of different connection types on the composite beam – column joint under repeated loading as well as to investigate new forms of slab connection with column flange in composite connection joints, aiming to enhance the behaviors of the joints and make the slab endure a part of the load in a more efficient way. Five specimens with various connection types were tested to failure; the composite model number two (CM2) was considered the control specimen. Regarding the ultimate moment, the result found that CM5 has moment 50.47% more than control specimen, the lowest rotation value was in CM5. The general behaviours of the FEM were in good accordance with the experiment results. According to the parametric a higher yield strength is more rigid stiffer, the effect of web thickness on the load is too small and increase in load resistance with an increase in beam flange thickness.