D. V. Orlov
Research Subjects
D. V. Orlov has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- A. A. Pokhvalityi
Dnipro State Technical University (DDTU) (Kamianske, Ukraine)
3 shared publications - Ye. M. Sigarev
Dniprovsky State Technical University (Kamianske, Ukraine)
3 shared publications - Oleksiy Mykolaiovych Smirnov
Physico-Technological Institute of Metals and Alloys of the National Academy of Sciences of Ukraine, Kyiv, Ukraine
2 shared publications - Sergii Semiriagin
Physico-technological Institute of Metals and Alloys of the NAS of Ukraine (Kyiv, Ukraine)
2 shared publications - Yuliia P. Skorobagatko
Physico-technological Institute of Metals and Alloys of the NAS of Ukraine (Kyiv, Ukraine)
2 shared publications Yu. P. Skorobahatko
Physico-Technological Institute of Metals and Alloys of the National Academy of Sciences of Ukraine, Kyiv, Ukraine
1 shared publication
Latest Publications
- Open Access
- 7 September 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 165 (3) , 14-24
RESEARCH INTO THE PROCESS OF OBTAINING HIGH-SILICINE FERRO-CARBON ALLOY ФС15л FOR THE MANUFACTURE OF CORROSION-RESISTANT PARTS OF SULFURIC ACID PRODUCTION EQUIPMENT. Mеssage 1
The work investigates the technology of obtaining high-silicon iron-carbon alloy of the ФС15л brand, intended for the manufacture of parts of chemical equipment operating in aggressive acidic environments. The choice of an alloy with a silicon content of 13–15% as a material for the production of tanks of rectification columns for drying sulfuric acid is justified due to its high corrosion resistance, ability to passivation and long service life. In the process of research, the preparation of charge materials, smelting and refining of the starting pig iron from sulfur by the method of magnesium treatment in an IST-016 induction furnace were carried out. Based on the refined pig iron, an iron-carbon melt with a silicon content within 13–15% was obtained, samples were taken for chemical and structural analysis, and the metal was poured into sand-clay molds. To prevent the formation of burn-in, non-stick powders based on powdered quartz were used. Shaped castings and plate samples were obtained for further metallographic, mechanical and corrosion studies. The features of the formation of the structure of high-silicon ferrosilicides, the influence of silicon on the corrosion resistance and technological properties of the alloy were considered. It was established that the silicon content at the level of 13–15% ensures the formation of a stable protective layer on the metal surface, which effectively prevents corrosion destruction in a concentrated sulfuric acid environment. It is shown that the use of alloys of the ФС15л type allows to significantly increase the durability and reliability of chemical equipment, reduce the costs of repair and maintenance and increase the service life of technological installations. The results obtained confirm the prospects of using high-silicon iron-carbon alloys for the manufacture of cast parts for sulfuric acid production and other branches of the chemical industry. У роботі досліджено технологію отримання висококремнистого залізовуглецевого сплаву марки ФС15л, призначеного для виготовлення деталей хімічного обладнання, що працює в умовах дії агресивних кислотних середовищ. Обґрунтовано вибір сплаву із вмістом кремнію 13–15 % як матеріалу для виробництва царг ректифікаційних колон сушіння сірчаної кислоти завдяки його високій корозійній стійкості, здатності до пасивації та тривалому терміну експлуатації. У процесі дослідження здійснено підготовку шихтових матеріалів, виплавку та рафінування вихідного чавуну від сірки методом обробки магнієм в індукційній печі ІСТ-016. На основі рафінованого чавуну одержано залізовуглецевий розплав із вмістом кремнію в межах 13–15 %, відібрано проби для хімічного та структурного аналізу, а також здійснено розливання металу в піщано-глинисті суміші. Для запобігання утворенню пригару використано протипригарні присипки на основі пиловидного кварцу. Було одержано фасонні відливки та пластинчасті зразки для проведення подальших металографічних, механічних і корозійних досліджень. Розглянуто особливості формування структури висококремнистих феросиліцидів, вплив кремнію на корозійну стійкість і технологічні властивості сплаву. Встановлено, що вміст кремнію на рівні 13–15 % забезпечує формування стійкого захисного шару на поверхні металу, який ефективно перешкоджає корозійному руйнуванню в середовищі концентрованої сірчаної кислоти. Показано, що застосування сплавів типу ФС15л дозволяє суттєво підвищити довговічність та надійність хімічного обладнання, знизити витрати на ремонт і технічне обслуговування та збільшити міжремонтний ресурс технологічних установок. Отримані результати підтверджують перспективність використання висококремнистих залізовуглецевих сплавів для виготовлення литих деталей сірчанокислотного виробництва та інших галузей хімічної промисловості.
- 7 September 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 165 (3) , 14-24
Open AccessRESEARCH INTO THE PROCESS OF OBTAINING HIGH-SILICINE FERRO-CARBON ALLOY ФС15л FOR THE MANUFACTURE OF CORROSION-RESISTANT PARTS OF SULFURIC ACID PRODUCTION EQUIPMENT. Mеssage 1
The work investigates the technology of obtaining high-silicon iron-carbon alloy of the ФС15л brand, intended for the manufacture of parts of chemical equipment operating in aggressive acidic environments. The choice of an alloy with a silicon content of 13–15% as a material for the production of tanks of rectification columns for drying sulfuric acid is justified due to its high corrosion resistance, ability to passivation and long service life. In the process of research, the preparation of charge materials, smelting and refining of the starting pig iron from sulfur by the method of magnesium treatment in an IST-016 induction furnace were carried out. Based on the refined pig iron, an iron-carbon melt with a silicon content within 13–15% was obtained, samples were taken for chemical and structural analysis, and the metal was poured into sand-clay molds. To prevent the formation of burn-in, non-stick powders based on powdered quartz were used. Shaped castings and plate samples were obtained for further metallographic, mechanical and corrosion studies. The features of the formation of the structure of high-silicon ferrosilicides, the influence of silicon on the corrosion resistance and technological properties of the alloy were considered. It was established that the silicon content at the level of 13–15% ensures the formation of a stable protective layer on the metal surface, which effectively prevents corrosion destruction in a concentrated sulfuric acid environment. It is shown that the use of alloys of the ФС15л type allows to significantly increase the durability and reliability of chemical equipment, reduce the costs of repair and maintenance and increase the service life of technological installations. The results obtained confirm the prospects of using high-silicon iron-carbon alloys for the manufacture of cast parts for sulfuric acid production and other branches of the chemical industry. У роботі досліджено технологію отримання висококремнистого залізовуглецевого сплаву марки ФС15л, призначеного для виготовлення деталей хімічного обладнання, що працює в умовах дії агресивних кислотних середовищ. Обґрунтовано вибір сплаву із вмістом кремнію 13–15 % як матеріалу для виробництва царг ректифікаційних колон сушіння сірчаної кислоти завдяки його високій корозійній стійкості, здатності до пасивації та тривалому терміну експлуатації. У процесі дослідження здійснено підготовку шихтових матеріалів, виплавку та рафінування вихідного чавуну від сірки методом обробки магнієм в індукційній печі ІСТ-016. На основі рафінованого чавуну одержано залізовуглецевий розплав із вмістом кремнію в межах 13–15 %, відібрано проби для хімічного та структурного аналізу, а також здійснено розливання металу в піщано-глинисті суміші. Для запобігання утворенню пригару використано протипригарні присипки на основі пиловидного кварцу. Було одержано фасонні відливки та пластинчасті зразки для проведення подальших металографічних, механічних і корозійних досліджень. Розглянуто особливості формування структури висококремнистих феросиліцидів, вплив кремнію на корозійну стійкість і технологічні властивості сплаву. Встановлено, що вміст кремнію на рівні 13–15 % забезпечує формування стійкого захисного шару на поверхні металу, який ефективно перешкоджає корозійному руйнуванню в середовищі концентрованої сірчаної кислоти. Показано, що застосування сплавів типу ФС15л дозволяє суттєво підвищити довговічність та надійність хімічного обладнання, знизити витрати на ремонт і технічне обслуговування та збільшити міжремонтний ресурс технологічних установок. Отримані результати підтверджують перспективність використання висококремнистих залізовуглецевих сплавів для виготовлення литих деталей сірчанокислотного виробництва та інших галузей хімічної промисловості.
- Open Access
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 164 (2) , 39-54
ОБҐРУНТУВАННЯ ВИБОРУ ВИСОКОКРЕМНИСТОГО СПЛАВУ НА ОСНОВІ ЗАЛІЗА ДЛЯ ВИГОТОВЛЕННЯ ЦАРГ РЕКТИФІКАЦІЙНИХ КОЛОН. ОГЛЯД
Operation of distillation columns in sulfur dioxide drying plants is accompanied by extreme corrosive effects of concentrated sulfuric acid (H2SO4) and anhydrides at temperatures up to 100-120 °C. Conventional stainless steels in such conditions demonstrate unsatisfactory resistance, which leads to frequent emergency shutdowns. The use of high-silicon cast irons (ferrosilicides) is technologically justified, but requires strict justification of the composition and structure due to their high fragility. It has been established that for the formation of a continuous protective film of silicon dioxide SiO2 capable of self-healing, the silicon content in the ferruginous matrix should be 14.5–15.5% (grade ЧС15). A lower silicon content leads to pitting corrosion, a higher one to critical embrittlement of castings. It has been proven that traditional lamellar graphite is the main factor in premature destruction of the tsarg due to the «wicking effect» (capillary penetration of acid deep into the metal). It is recommended to switch to point or spherical graphite by modifying the melt, which reduces the corrosion rate by 3–5 times. To stabilize the passive state during temperature fluctuations and work with «dirty» technical acids, the feasibility of alloying with 1% Mo and 1% Ni (Fe15Si) has been substantiated. Molybdenum strengthens the oxide layer against the action of chlorides, and nickel refines the grain, improving the mechanical strength of flange joints. The introduction of an alloyed high-strength alloy instead of basic grades allows you to increase the equipment overhaul interval from 4 to 8–10 years. Despite the increase in raw material costs by 25–30%, the total cost of ownership is reduced by 35% due to the absence of emergency downtime and a decrease in the number of replacements of expensive column sections. Експлуатацію ректифікаційних колон у цехах сушіння сірчистого газу супроводжує екстремальний корозійний вплив концентрованої сірчаної кислоти (H2SO4) та ангідридів при температурах до 100–120 ºC. Звичайні нержавіючі сталі в таких умовах демонструють незадовільну стійкість, що призводить до частих аварійних зупинок. Використання висо- кремнистих чавунів (феросиліцидів) є технологічно виправданим, проте потребує суворого обґрунтування складу та структури через їх високу крихкість. Встановлено, що для формування суцільної захисної плівки діоксиду кремнію SiO2, здатної до самовідновлення, вміст кремнію в залізистій матриці має становити 14,5–15,5 % (марка ЧС15). Нижчий вміст кремнію призводить до точкової корозії, вищий — до критичного окрихчення відливок. Доведено, що традиційний пластинчастий графіт є головним чинником передчасного руйнування царг через «ефект гніту» (капілярне проникнення кислоти вглиб металу). Рекомендовано перехід до точкового або кулястого графіту шляхом модифікування розплаву, що знижує швидкість корозії у 3–5 разів. Для стабілізації пасивного стану при температурних коливаннях та роботі з «брудними» технічними кислотами обґрунтовано доцільність легування 1 % Mo та 1 % Ni (Fe15Si). Молібден зміцнює оксидний шар проти дії хлоридів, а нікель подрібнює зерно, покращуючи механічну витривалість фланцевих з’єднань. Впровадження легованого високремнистого сплаву замість базових марок дозволяє збільшити міжремонтний інтервал обладнання з 4 до 8–10 років. Попри зростання вартості сировини на 25–30 %, сумарні витрати на володіння знижуються на 35 % за рахунок відсутності аварійних простоїв та зменшення кількості замін дороговартісних секцій колон.
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 164 (2) , 39-54
Open AccessОБҐРУНТУВАННЯ ВИБОРУ ВИСОКОКРЕМНИСТОГО СПЛАВУ НА ОСНОВІ ЗАЛІЗА ДЛЯ ВИГОТОВЛЕННЯ ЦАРГ РЕКТИФІКАЦІЙНИХ КОЛОН. ОГЛЯД
Operation of distillation columns in sulfur dioxide drying plants is accompanied by extreme corrosive effects of concentrated sulfuric acid (H2SO4) and anhydrides at temperatures up to 100-120 °C. Conventional stainless steels in such conditions demonstrate unsatisfactory resistance, which leads to frequent emergency shutdowns. The use of high-silicon cast irons (ferrosilicides) is technologically justified, but requires strict justification of the composition and structure due to their high fragility. It has been established that for the formation of a continuous protective film of silicon dioxide SiO2 capable of self-healing, the silicon content in the ferruginous matrix should be 14.5–15.5% (grade ЧС15). A lower silicon content leads to pitting corrosion, a higher one to critical embrittlement of castings. It has been proven that traditional lamellar graphite is the main factor in premature destruction of the tsarg due to the «wicking effect» (capillary penetration of acid deep into the metal). It is recommended to switch to point or spherical graphite by modifying the melt, which reduces the corrosion rate by 3–5 times. To stabilize the passive state during temperature fluctuations and work with «dirty» technical acids, the feasibility of alloying with 1% Mo and 1% Ni (Fe15Si) has been substantiated. Molybdenum strengthens the oxide layer against the action of chlorides, and nickel refines the grain, improving the mechanical strength of flange joints. The introduction of an alloyed high-strength alloy instead of basic grades allows you to increase the equipment overhaul interval from 4 to 8–10 years. Despite the increase in raw material costs by 25–30%, the total cost of ownership is reduced by 35% due to the absence of emergency downtime and a decrease in the number of replacements of expensive column sections. Експлуатацію ректифікаційних колон у цехах сушіння сірчистого газу супроводжує екстремальний корозійний вплив концентрованої сірчаної кислоти (H2SO4) та ангідридів при температурах до 100–120 ºC. Звичайні нержавіючі сталі в таких умовах демонструють незадовільну стійкість, що призводить до частих аварійних зупинок. Використання висо- кремнистих чавунів (феросиліцидів) є технологічно виправданим, проте потребує суворого обґрунтування складу та структури через їх високу крихкість. Встановлено, що для формування суцільної захисної плівки діоксиду кремнію SiO2, здатної до самовідновлення, вміст кремнію в залізистій матриці має становити 14,5–15,5 % (марка ЧС15). Нижчий вміст кремнію призводить до точкової корозії, вищий — до критичного окрихчення відливок. Доведено, що традиційний пластинчастий графіт є головним чинником передчасного руйнування царг через «ефект гніту» (капілярне проникнення кислоти вглиб металу). Рекомендовано перехід до точкового або кулястого графіту шляхом модифікування розплаву, що знижує швидкість корозії у 3–5 разів. Для стабілізації пасивного стану при температурних коливаннях та роботі з «брудними» технічними кислотами обґрунтовано доцільність легування 1 % Mo та 1 % Ni (Fe15Si). Молібден зміцнює оксидний шар проти дії хлоридів, а нікель подрібнює зерно, покращуючи механічну витривалість фланцевих з’єднань. Впровадження легованого високремнистого сплаву замість базових марок дозволяє збільшити міжремонтний інтервал обладнання з 4 до 8–10 років. Попри зростання вартості сировини на 25–30 %, сумарні витрати на володіння знижуються на 35 % за рахунок відсутності аварійних простоїв та зменшення кількості замін дороговартісних секцій колон.
- Open Access
- 30 March 2026
- Published by Ukrainian State University of Science and Technologies
- No. 1,p. 54-62
Increasing the corrosion resistance of ferrosilide in hot sulfuric acid by alloying with chromium, nickel and molybdenum
The corrosion resistance of ferrosilides of the Fe-Si-Cr-Ni-Mo-Mn system in concentrated sulfuric acid in the temperature range of 25-200°C was investigated. The corrosion rate was calculated based on electrochemical parameters using passivation and temperature dependence models of the Arrhenius type. It was confirmed that the main factor determining corrosion resistance is the silicon content. The existence of a critical Si content threshold was shown, upon reaching which a continuous passive SiO₂ film is formed, which provides a reduction in the corrosion rate by 1-2 orders of magnitude. Characteristic temperature ranges of the corrosion process were identified: stable passivation (25-80°C), transitional regime (80-150°C) and degradation of the passive state (150-200°C). It has been shown that Cr and Mo in Fe-Si alloys enhance the stability of the passivated state, particularly at high sulfuric acid temperatures, whereas Ni primarily affects the electrochemical characteristics, and Mn reduces the effectiveness of passivation. The effectiveness of adding chromium to Fe-Si alloys increases proportionally with the Si content; molybdenum stabilizes passivation at acid temperatures above 150°C and reduces the rate of localized corrosion; nickel is not a determining factor at high acid temperatures. The influence of operational factors (turbulence, erosion, impurities) on the corrosion rate has been determined. The expected corrosion rates for the studied alloys in sulfuric acid have been calculated, taking into account industrial operating conditions. The experimental data obtained can be used to develop new corrosion-resistant materials and optimize the composition of Fe-Si alloys for operation in high-temperature aggressive environments of concentrated sulfuric acid.
- 30 March 2026
- Published by Ukrainian State University of Science and Technologies
- No. 1,p. 54-62
Open AccessIncreasing the corrosion resistance of ferrosilide in hot sulfuric acid by alloying with chromium, nickel and molybdenum
The corrosion resistance of ferrosilides of the Fe-Si-Cr-Ni-Mo-Mn system in concentrated sulfuric acid in the temperature range of 25-200°C was investigated. The corrosion rate was calculated based on electrochemical parameters using passivation and temperature dependence models of the Arrhenius type. It was confirmed that the main factor determining corrosion resistance is the silicon content. The existence of a critical Si content threshold was shown, upon reaching which a continuous passive SiO₂ film is formed, which provides a reduction in the corrosion rate by 1-2 orders of magnitude. Characteristic temperature ranges of the corrosion process were identified: stable passivation (25-80°C), transitional regime (80-150°C) and degradation of the passive state (150-200°C). It has been shown that Cr and Mo in Fe-Si alloys enhance the stability of the passivated state, particularly at high sulfuric acid temperatures, whereas Ni primarily affects the electrochemical characteristics, and Mn reduces the effectiveness of passivation. The effectiveness of adding chromium to Fe-Si alloys increases proportionally with the Si content; molybdenum stabilizes passivation at acid temperatures above 150°C and reduces the rate of localized corrosion; nickel is not a determining factor at high acid temperatures. The influence of operational factors (turbulence, erosion, impurities) on the corrosion rate has been determined. The expected corrosion rates for the studied alloys in sulfuric acid have been calculated, taking into account industrial operating conditions. The experimental data obtained can be used to develop new corrosion-resistant materials and optimize the composition of Fe-Si alloys for operation in high-temperature aggressive environments of concentrated sulfuric acid.