A. A. Pokhvalityi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
A. A. Pokhvalityi has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Ye. M. Sigarev
Dniprovsky State Technical University (Kamianske, Ukraine)
8 shared publications - D. V. Orlov
LLC “TURBOGAZ UZHGOROD
3 shared publications - Mykola Rudenko
Дніпровський державний технічний університет (Кам’янське, Україна)
3 shared publications - Anatoliy Chernyatevich
Dniprovsk State Technical University
2 shared publications - Dmytro Kondrashenkov
Дніпровський державний технічний університет, м. Кам'янське
2 shared publications - Gennady Yuriyovych Kryachko
Dniprovsky State Technical University, Kamianske
2 shared publications
Latest Publications
- Open Access
- 7 September 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 165 (3) , 14-24
RESEARCH INTO THE PROCESS OF OBTAINING HIGH-SILICINE FERRO-CARBON ALLOY ФС15л FOR THE MANUFACTURE OF CORROSION-RESISTANT PARTS OF SULFURIC ACID PRODUCTION EQUIPMENT. Mеssage 1
The work investigates the technology of obtaining high-silicon iron-carbon alloy of the ФС15л brand, intended for the manufacture of parts of chemical equipment operating in aggressive acidic environments. The choice of an alloy with a silicon content of 13–15% as a material for the production of tanks of rectification columns for drying sulfuric acid is justified due to its high corrosion resistance, ability to passivation and long service life. In the process of research, the preparation of charge materials, smelting and refining of the starting pig iron from sulfur by the method of magnesium treatment in an IST-016 induction furnace were carried out. Based on the refined pig iron, an iron-carbon melt with a silicon content within 13–15% was obtained, samples were taken for chemical and structural analysis, and the metal was poured into sand-clay molds. To prevent the formation of burn-in, non-stick powders based on powdered quartz were used. Shaped castings and plate samples were obtained for further metallographic, mechanical and corrosion studies. The features of the formation of the structure of high-silicon ferrosilicides, the influence of silicon on the corrosion resistance and technological properties of the alloy were considered. It was established that the silicon content at the level of 13–15% ensures the formation of a stable protective layer on the metal surface, which effectively prevents corrosion destruction in a concentrated sulfuric acid environment. It is shown that the use of alloys of the ФС15л type allows to significantly increase the durability and reliability of chemical equipment, reduce the costs of repair and maintenance and increase the service life of technological installations. The results obtained confirm the prospects of using high-silicon iron-carbon alloys for the manufacture of cast parts for sulfuric acid production and other branches of the chemical industry. У роботі досліджено технологію отримання висококремнистого залізовуглецевого сплаву марки ФС15л, призначеного для виготовлення деталей хімічного обладнання, що працює в умовах дії агресивних кислотних середовищ. Обґрунтовано вибір сплаву із вмістом кремнію 13–15 % як матеріалу для виробництва царг ректифікаційних колон сушіння сірчаної кислоти завдяки його високій корозійній стійкості, здатності до пасивації та тривалому терміну експлуатації. У процесі дослідження здійснено підготовку шихтових матеріалів, виплавку та рафінування вихідного чавуну від сірки методом обробки магнієм в індукційній печі ІСТ-016. На основі рафінованого чавуну одержано залізовуглецевий розплав із вмістом кремнію в межах 13–15 %, відібрано проби для хімічного та структурного аналізу, а також здійснено розливання металу в піщано-глинисті суміші. Для запобігання утворенню пригару використано протипригарні присипки на основі пиловидного кварцу. Було одержано фасонні відливки та пластинчасті зразки для проведення подальших металографічних, механічних і корозійних досліджень. Розглянуто особливості формування структури висококремнистих феросиліцидів, вплив кремнію на корозійну стійкість і технологічні властивості сплаву. Встановлено, що вміст кремнію на рівні 13–15 % забезпечує формування стійкого захисного шару на поверхні металу, який ефективно перешкоджає корозійному руйнуванню в середовищі концентрованої сірчаної кислоти. Показано, що застосування сплавів типу ФС15л дозволяє суттєво підвищити довговічність та надійність хімічного обладнання, знизити витрати на ремонт і технічне обслуговування та збільшити міжремонтний ресурс технологічних установок. Отримані результати підтверджують перспективність використання висококремнистих залізовуглецевих сплавів для виготовлення литих деталей сірчанокислотного виробництва та інших галузей хімічної промисловості.
- 7 September 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 165 (3) , 14-24
Open AccessRESEARCH INTO THE PROCESS OF OBTAINING HIGH-SILICINE FERRO-CARBON ALLOY ФС15л FOR THE MANUFACTURE OF CORROSION-RESISTANT PARTS OF SULFURIC ACID PRODUCTION EQUIPMENT. Mеssage 1
The work investigates the technology of obtaining high-silicon iron-carbon alloy of the ФС15л brand, intended for the manufacture of parts of chemical equipment operating in aggressive acidic environments. The choice of an alloy with a silicon content of 13–15% as a material for the production of tanks of rectification columns for drying sulfuric acid is justified due to its high corrosion resistance, ability to passivation and long service life. In the process of research, the preparation of charge materials, smelting and refining of the starting pig iron from sulfur by the method of magnesium treatment in an IST-016 induction furnace were carried out. Based on the refined pig iron, an iron-carbon melt with a silicon content within 13–15% was obtained, samples were taken for chemical and structural analysis, and the metal was poured into sand-clay molds. To prevent the formation of burn-in, non-stick powders based on powdered quartz were used. Shaped castings and plate samples were obtained for further metallographic, mechanical and corrosion studies. The features of the formation of the structure of high-silicon ferrosilicides, the influence of silicon on the corrosion resistance and technological properties of the alloy were considered. It was established that the silicon content at the level of 13–15% ensures the formation of a stable protective layer on the metal surface, which effectively prevents corrosion destruction in a concentrated sulfuric acid environment. It is shown that the use of alloys of the ФС15л type allows to significantly increase the durability and reliability of chemical equipment, reduce the costs of repair and maintenance and increase the service life of technological installations. The results obtained confirm the prospects of using high-silicon iron-carbon alloys for the manufacture of cast parts for sulfuric acid production and other branches of the chemical industry. У роботі досліджено технологію отримання висококремнистого залізовуглецевого сплаву марки ФС15л, призначеного для виготовлення деталей хімічного обладнання, що працює в умовах дії агресивних кислотних середовищ. Обґрунтовано вибір сплаву із вмістом кремнію 13–15 % як матеріалу для виробництва царг ректифікаційних колон сушіння сірчаної кислоти завдяки його високій корозійній стійкості, здатності до пасивації та тривалому терміну експлуатації. У процесі дослідження здійснено підготовку шихтових матеріалів, виплавку та рафінування вихідного чавуну від сірки методом обробки магнієм в індукційній печі ІСТ-016. На основі рафінованого чавуну одержано залізовуглецевий розплав із вмістом кремнію в межах 13–15 %, відібрано проби для хімічного та структурного аналізу, а також здійснено розливання металу в піщано-глинисті суміші. Для запобігання утворенню пригару використано протипригарні присипки на основі пиловидного кварцу. Було одержано фасонні відливки та пластинчасті зразки для проведення подальших металографічних, механічних і корозійних досліджень. Розглянуто особливості формування структури висококремнистих феросиліцидів, вплив кремнію на корозійну стійкість і технологічні властивості сплаву. Встановлено, що вміст кремнію на рівні 13–15 % забезпечує формування стійкого захисного шару на поверхні металу, який ефективно перешкоджає корозійному руйнуванню в середовищі концентрованої сірчаної кислоти. Показано, що застосування сплавів типу ФС15л дозволяє суттєво підвищити довговічність та надійність хімічного обладнання, знизити витрати на ремонт і технічне обслуговування та збільшити міжремонтний ресурс технологічних установок. Отримані результати підтверджують перспективність використання висококремнистих залізовуглецевих сплавів для виготовлення литих деталей сірчанокислотного виробництва та інших галузей хімічної промисловості.
- Open Access
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 164 (2) , 39-54
ОБҐРУНТУВАННЯ ВИБОРУ ВИСОКОКРЕМНИСТОГО СПЛАВУ НА ОСНОВІ ЗАЛІЗА ДЛЯ ВИГОТОВЛЕННЯ ЦАРГ РЕКТИФІКАЦІЙНИХ КОЛОН. ОГЛЯД
Operation of distillation columns in sulfur dioxide drying plants is accompanied by extreme corrosive effects of concentrated sulfuric acid (H2SO4) and anhydrides at temperatures up to 100-120 °C. Conventional stainless steels in such conditions demonstrate unsatisfactory resistance, which leads to frequent emergency shutdowns. The use of high-silicon cast irons (ferrosilicides) is technologically justified, but requires strict justification of the composition and structure due to their high fragility. It has been established that for the formation of a continuous protective film of silicon dioxide SiO2 capable of self-healing, the silicon content in the ferruginous matrix should be 14.5–15.5% (grade ЧС15). A lower silicon content leads to pitting corrosion, a higher one to critical embrittlement of castings. It has been proven that traditional lamellar graphite is the main factor in premature destruction of the tsarg due to the «wicking effect» (capillary penetration of acid deep into the metal). It is recommended to switch to point or spherical graphite by modifying the melt, which reduces the corrosion rate by 3–5 times. To stabilize the passive state during temperature fluctuations and work with «dirty» technical acids, the feasibility of alloying with 1% Mo and 1% Ni (Fe15Si) has been substantiated. Molybdenum strengthens the oxide layer against the action of chlorides, and nickel refines the grain, improving the mechanical strength of flange joints. The introduction of an alloyed high-strength alloy instead of basic grades allows you to increase the equipment overhaul interval from 4 to 8–10 years. Despite the increase in raw material costs by 25–30%, the total cost of ownership is reduced by 35% due to the absence of emergency downtime and a decrease in the number of replacements of expensive column sections. Експлуатацію ректифікаційних колон у цехах сушіння сірчистого газу супроводжує екстремальний корозійний вплив концентрованої сірчаної кислоти (H2SO4) та ангідридів при температурах до 100–120 ºC. Звичайні нержавіючі сталі в таких умовах демонструють незадовільну стійкість, що призводить до частих аварійних зупинок. Використання висо- кремнистих чавунів (феросиліцидів) є технологічно виправданим, проте потребує суворого обґрунтування складу та структури через їх високу крихкість. Встановлено, що для формування суцільної захисної плівки діоксиду кремнію SiO2, здатної до самовідновлення, вміст кремнію в залізистій матриці має становити 14,5–15,5 % (марка ЧС15). Нижчий вміст кремнію призводить до точкової корозії, вищий — до критичного окрихчення відливок. Доведено, що традиційний пластинчастий графіт є головним чинником передчасного руйнування царг через «ефект гніту» (капілярне проникнення кислоти вглиб металу). Рекомендовано перехід до точкового або кулястого графіту шляхом модифікування розплаву, що знижує швидкість корозії у 3–5 разів. Для стабілізації пасивного стану при температурних коливаннях та роботі з «брудними» технічними кислотами обґрунтовано доцільність легування 1 % Mo та 1 % Ni (Fe15Si). Молібден зміцнює оксидний шар проти дії хлоридів, а нікель подрібнює зерно, покращуючи механічну витривалість фланцевих з’єднань. Впровадження легованого високремнистого сплаву замість базових марок дозволяє збільшити міжремонтний інтервал обладнання з 4 до 8–10 років. Попри зростання вартості сировини на 25–30 %, сумарні витрати на володіння знижуються на 35 % за рахунок відсутності аварійних простоїв та зменшення кількості замін дороговартісних секцій колон.
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 164 (2) , 39-54
Open AccessОБҐРУНТУВАННЯ ВИБОРУ ВИСОКОКРЕМНИСТОГО СПЛАВУ НА ОСНОВІ ЗАЛІЗА ДЛЯ ВИГОТОВЛЕННЯ ЦАРГ РЕКТИФІКАЦІЙНИХ КОЛОН. ОГЛЯД
Operation of distillation columns in sulfur dioxide drying plants is accompanied by extreme corrosive effects of concentrated sulfuric acid (H2SO4) and anhydrides at temperatures up to 100-120 °C. Conventional stainless steels in such conditions demonstrate unsatisfactory resistance, which leads to frequent emergency shutdowns. The use of high-silicon cast irons (ferrosilicides) is technologically justified, but requires strict justification of the composition and structure due to their high fragility. It has been established that for the formation of a continuous protective film of silicon dioxide SiO2 capable of self-healing, the silicon content in the ferruginous matrix should be 14.5–15.5% (grade ЧС15). A lower silicon content leads to pitting corrosion, a higher one to critical embrittlement of castings. It has been proven that traditional lamellar graphite is the main factor in premature destruction of the tsarg due to the «wicking effect» (capillary penetration of acid deep into the metal). It is recommended to switch to point or spherical graphite by modifying the melt, which reduces the corrosion rate by 3–5 times. To stabilize the passive state during temperature fluctuations and work with «dirty» technical acids, the feasibility of alloying with 1% Mo and 1% Ni (Fe15Si) has been substantiated. Molybdenum strengthens the oxide layer against the action of chlorides, and nickel refines the grain, improving the mechanical strength of flange joints. The introduction of an alloyed high-strength alloy instead of basic grades allows you to increase the equipment overhaul interval from 4 to 8–10 years. Despite the increase in raw material costs by 25–30%, the total cost of ownership is reduced by 35% due to the absence of emergency downtime and a decrease in the number of replacements of expensive column sections. Експлуатацію ректифікаційних колон у цехах сушіння сірчистого газу супроводжує екстремальний корозійний вплив концентрованої сірчаної кислоти (H2SO4) та ангідридів при температурах до 100–120 ºC. Звичайні нержавіючі сталі в таких умовах демонструють незадовільну стійкість, що призводить до частих аварійних зупинок. Використання висо- кремнистих чавунів (феросиліцидів) є технологічно виправданим, проте потребує суворого обґрунтування складу та структури через їх високу крихкість. Встановлено, що для формування суцільної захисної плівки діоксиду кремнію SiO2, здатної до самовідновлення, вміст кремнію в залізистій матриці має становити 14,5–15,5 % (марка ЧС15). Нижчий вміст кремнію призводить до точкової корозії, вищий — до критичного окрихчення відливок. Доведено, що традиційний пластинчастий графіт є головним чинником передчасного руйнування царг через «ефект гніту» (капілярне проникнення кислоти вглиб металу). Рекомендовано перехід до точкового або кулястого графіту шляхом модифікування розплаву, що знижує швидкість корозії у 3–5 разів. Для стабілізації пасивного стану при температурних коливаннях та роботі з «брудними» технічними кислотами обґрунтовано доцільність легування 1 % Mo та 1 % Ni (Fe15Si). Молібден зміцнює оксидний шар проти дії хлоридів, а нікель подрібнює зерно, покращуючи механічну витривалість фланцевих з’єднань. Впровадження легованого високремнистого сплаву замість базових марок дозволяє збільшити міжремонтний інтервал обладнання з 4 до 8–10 років. Попри зростання вартості сировини на 25–30 %, сумарні витрати на володіння знижуються на 35 % за рахунок відсутності аварійних простоїв та зменшення кількості замін дороговартісних секцій колон.
- Open Access
- 30 March 2026
- Published by Ukrainian State University of Science and Technologies
- No. 1,p. 54-62
Increasing the corrosion resistance of ferrosilide in hot sulfuric acid by alloying with chromium, nickel and molybdenum
The corrosion resistance of ferrosilides of the Fe-Si-Cr-Ni-Mo-Mn system in concentrated sulfuric acid in the temperature range of 25-200°C was investigated. The corrosion rate was calculated based on electrochemical parameters using passivation and temperature dependence models of the Arrhenius type. It was confirmed that the main factor determining corrosion resistance is the silicon content. The existence of a critical Si content threshold was shown, upon reaching which a continuous passive SiO₂ film is formed, which provides a reduction in the corrosion rate by 1-2 orders of magnitude. Characteristic temperature ranges of the corrosion process were identified: stable passivation (25-80°C), transitional regime (80-150°C) and degradation of the passive state (150-200°C). It has been shown that Cr and Mo in Fe-Si alloys enhance the stability of the passivated state, particularly at high sulfuric acid temperatures, whereas Ni primarily affects the electrochemical characteristics, and Mn reduces the effectiveness of passivation. The effectiveness of adding chromium to Fe-Si alloys increases proportionally with the Si content; molybdenum stabilizes passivation at acid temperatures above 150°C and reduces the rate of localized corrosion; nickel is not a determining factor at high acid temperatures. The influence of operational factors (turbulence, erosion, impurities) on the corrosion rate has been determined. The expected corrosion rates for the studied alloys in sulfuric acid have been calculated, taking into account industrial operating conditions. The experimental data obtained can be used to develop new corrosion-resistant materials and optimize the composition of Fe-Si alloys for operation in high-temperature aggressive environments of concentrated sulfuric acid.
- 30 March 2026
- Published by Ukrainian State University of Science and Technologies
- No. 1,p. 54-62
Open AccessIncreasing the corrosion resistance of ferrosilide in hot sulfuric acid by alloying with chromium, nickel and molybdenum
The corrosion resistance of ferrosilides of the Fe-Si-Cr-Ni-Mo-Mn system in concentrated sulfuric acid in the temperature range of 25-200°C was investigated. The corrosion rate was calculated based on electrochemical parameters using passivation and temperature dependence models of the Arrhenius type. It was confirmed that the main factor determining corrosion resistance is the silicon content. The existence of a critical Si content threshold was shown, upon reaching which a continuous passive SiO₂ film is formed, which provides a reduction in the corrosion rate by 1-2 orders of magnitude. Characteristic temperature ranges of the corrosion process were identified: stable passivation (25-80°C), transitional regime (80-150°C) and degradation of the passive state (150-200°C). It has been shown that Cr and Mo in Fe-Si alloys enhance the stability of the passivated state, particularly at high sulfuric acid temperatures, whereas Ni primarily affects the electrochemical characteristics, and Mn reduces the effectiveness of passivation. The effectiveness of adding chromium to Fe-Si alloys increases proportionally with the Si content; molybdenum stabilizes passivation at acid temperatures above 150°C and reduces the rate of localized corrosion; nickel is not a determining factor at high acid temperatures. The influence of operational factors (turbulence, erosion, impurities) on the corrosion rate has been determined. The expected corrosion rates for the studied alloys in sulfuric acid have been calculated, taking into account industrial operating conditions. The experimental data obtained can be used to develop new corrosion-resistant materials and optimize the composition of Fe-Si alloys for operation in high-temperature aggressive environments of concentrated sulfuric acid.
- Open Access
- 15 February 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Science and innovation
- Vol. 22 (1) , 107-122
АНАЛІЗ ПРИЧИН ТА НАСЛІДКІВ РЕЗОНАНСНИХ АВАРІЙ ДОМЕННИХ ПЕЧЕЙ
Вступ. Доменна піч, разом з повітронагрівальною і газоочисною технікою, залишається однією з найнебезпечних металургійних систем. Особливої уваги потребують аварії з катастрофічними наслідками якдля обладнання, так і для техперсоналу. Вони не мають терміну давності й повинні ретельно вивчатисязадля усунення причин їх виникнення та безпечного функціонування.Проблематика. Недостатнє, а іноді й протирічне, висвітлення у технічній літературі інформації про особливо важкі аварії, зокрема вибухи печей, є перепоною для подальшого удосконалення та розробки безпечної технології ведення доменного процесу, тому пошук засобів запобігання та уникнення аварійних ситуацій є актуальним.Мета. Встановити дійсний механізм вибухового руйнування доменної печі №7 Дніпровського металургійного комбінату (ДМК) 07.09.1993 р. з розглядом факторів об’єктивного та суб’єктивного впливів.Матеріали й методи. Для аналізу використано архівні матеріали візуалізації параметрів роботи печі напаперових носіях, фотодокументи, акти й висновки експертних комісій, а також публікації з досліджуваного питання.Результати. Відтворено механізм вибухового руйнування ДП №7 ДМК (Україна). Систематизовано фактори, що спричинили аварійну ситуацію. Виконано порівняння причин і наслідків аварій на досліджуванійпечі і ДП №5 заводу в Port Talbot (Великобританія), що мали однаковий механізм катастрофічного руйнування агрегатів через неконтрольоване потрапляння критичної маси води в робочий простір печі.Висновки. Встановлено, що на ДП №7 ДМК значний масштаб руйнувань з численними людськими жертвами був обумовлений не одним, як вважалося раніше, а двома вибухами різної потужності. Показано динаміку зміни газодуттьового режиму задувального періоду, що призвело при відсутності сходу шихти на колошнику до вибухової аварії. Охарактеризовано важливість дотримання рекомендацій для недопущенняпарових вибухів у доменних печах. Результати дослідження є важливим доповненням до створення нормативних документів для забезпечення безаварійної експлуатації доменних печей.
- 15 February 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Science and innovation
- Vol. 22 (1) , 107-122
Open AccessАНАЛІЗ ПРИЧИН ТА НАСЛІДКІВ РЕЗОНАНСНИХ АВАРІЙ ДОМЕННИХ ПЕЧЕЙ
Вступ. Доменна піч, разом з повітронагрівальною і газоочисною технікою, залишається однією з найнебезпечних металургійних систем. Особливої уваги потребують аварії з катастрофічними наслідками якдля обладнання, так і для техперсоналу. Вони не мають терміну давності й повинні ретельно вивчатисязадля усунення причин їх виникнення та безпечного функціонування.Проблематика. Недостатнє, а іноді й протирічне, висвітлення у технічній літературі інформації про особливо важкі аварії, зокрема вибухи печей, є перепоною для подальшого удосконалення та розробки безпечної технології ведення доменного процесу, тому пошук засобів запобігання та уникнення аварійних ситуацій є актуальним.Мета. Встановити дійсний механізм вибухового руйнування доменної печі №7 Дніпровського металургійного комбінату (ДМК) 07.09.1993 р. з розглядом факторів об’єктивного та суб’єктивного впливів.Матеріали й методи. Для аналізу використано архівні матеріали візуалізації параметрів роботи печі напаперових носіях, фотодокументи, акти й висновки експертних комісій, а також публікації з досліджуваного питання.Результати. Відтворено механізм вибухового руйнування ДП №7 ДМК (Україна). Систематизовано фактори, що спричинили аварійну ситуацію. Виконано порівняння причин і наслідків аварій на досліджуванійпечі і ДП №5 заводу в Port Talbot (Великобританія), що мали однаковий механізм катастрофічного руйнування агрегатів через неконтрольоване потрапляння критичної маси води в робочий простір печі.Висновки. Встановлено, що на ДП №7 ДМК значний масштаб руйнувань з численними людськими жертвами був обумовлений не одним, як вважалося раніше, а двома вибухами різної потужності. Показано динаміку зміни газодуттьового режиму задувального періоду, що призвело при відсутності сходу шихти на колошнику до вибухової аварії. Охарактеризовано важливість дотримання рекомендацій для недопущенняпарових вибухів у доменних печах. Результати дослідження є важливим доповненням до створення нормативних документів для забезпечення безаварійної експлуатації доменних печей.
- 1 December 2025
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 39, 78-88
Research on the "hot" model of impurities behavior in cast iron during complex processing
The aim of this work is to establish the regularities of behavior and distribution of impurities in cast iron during complex treatment on a hot model, taking into account the influence of thermodynamic and kinetic factors, to optimize the cleaning processes and improve the quality of the metal. The complex treatment of molten iron involves the use of several technological effects, which allows for more effective control over the chemical composition and microstructure of the metal. The relevance of this treatment is driven by the need to produce high-quality alloys while reducing costs and improving environmental safety. An important tool for improving the technology is modeling the removal processes and the behavior of impurities in molten metal. Of particular value is research on so-called "hot" models that involve working directly with liquid iron. Calculations were performed for the conditions of injection treatment of cast iron for the purpose of complex removal of impurities in a laboratory induction furnace with a capacity of 100 kg. A general scheme of heat losses of liquid cast iron during complex refining from impurities by injecting reagents into carrier gases was constructed. It is worth noting the fact that this dosing device was first used to work with liquid cast iron. Prior to the "hot" treatments, cold tests of all equipment were performed, which showed that it was ready for the experimental part of the research. Four treatments were carried out. At the beginning and end of each treatment, samples of cast iron and slag were taken, and temperature measurements were also made. The amount of reagent dispensed was recorded according to the readings of the scales before and after the treatment. During the treatments, the technological parameters of the injection were worked out, which made it possible to carry out the treatment technologically, without increased turbulence. The analysis of the content of impurities in cast iron showed that, taking into account the conditions of the experiment, desulfurization, desilting and dephosphorization processes occur, including simultaneously.
- 1 December 2025
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 39, 78-88
Research on the "hot" model of impurities behavior in cast iron during complex processing
The aim of this work is to establish the regularities of behavior and distribution of impurities in cast iron during complex treatment on a hot model, taking into account the influence of thermodynamic and kinetic factors, to optimize the cleaning processes and improve the quality of the metal. The complex treatment of molten iron involves the use of several technological effects, which allows for more effective control over the chemical composition and microstructure of the metal. The relevance of this treatment is driven by the need to produce high-quality alloys while reducing costs and improving environmental safety. An important tool for improving the technology is modeling the removal processes and the behavior of impurities in molten metal. Of particular value is research on so-called "hot" models that involve working directly with liquid iron. Calculations were performed for the conditions of injection treatment of cast iron for the purpose of complex removal of impurities in a laboratory induction furnace with a capacity of 100 kg. A general scheme of heat losses of liquid cast iron during complex refining from impurities by injecting reagents into carrier gases was constructed. It is worth noting the fact that this dosing device was first used to work with liquid cast iron. Prior to the "hot" treatments, cold tests of all equipment were performed, which showed that it was ready for the experimental part of the research. Four treatments were carried out. At the beginning and end of each treatment, samples of cast iron and slag were taken, and temperature measurements were also made. The amount of reagent dispensed was recorded according to the readings of the scales before and after the treatment. During the treatments, the technological parameters of the injection were worked out, which made it possible to carry out the treatment technologically, without increased turbulence. The analysis of the content of impurities in cast iron showed that, taking into account the conditions of the experiment, desulfurization, desilting and dephosphorization processes occur, including simultaneously.
- Open Access
- 26 December 2024
- Published by SHEI Pryazovskyi State Technical University in Reporter of the Priazovskyi State Technical University. Section: Technical sciences
- Vol. 1 (49) , 200-207
Study of the conditions of gas-liquid flow formation during the tapping of the melt from the converter
The study of the conditions for the formation of a gas-liquid flow during the tapping of molten metal from the converter is based on low-temperature modeling, aimed at analyzing the impact of the structural characteristics of the steel tapping channel. The use of inert gas (argon) enabled the creation of a protective gas shell that reduces the contact of the metal with atmospheric oxygen, lowering its content in the flow to 1–3%. Based on the experiments, a classification of blowing regimes and empirical dependencies were developed to describe the interaction between the gas and the liquid. It was established that the minimum oxygen concentration in the gas phase (1–3%) is achieved with an argon flow of 10–20% of the maximum. This maintains the efficiency of the protective shell at 95%. Further increases in the argon flow lead to the expansion of the flow's opening angle, negatively impacting its organization. Increasing the number of nozzles improves flow stability: with six nozzles, the oxygen concentration remains below 10.5%, even with high gas flow rates. Experiments on a flat tapping channel model revealed a dependence between the gas flow, liquid level, and the depth of the vortex. Increasing the gas flow with a high liquid level contributes to the stability of the interfacial surface, whereas reducing the liquid level leads to an increase in vortex depth and deterioration of the flow organization. The experiments were conducted on a laboratory setup simulating the tapping process, accounting for geometric and dynamic similarity. Technically pure argon with an oxygen content of up to 0.7% was used. The main parameters for analysis included gas flow rate, liquid level, relative vortex depth, and flow opening angle. To assess the effectiveness of the gas shell, oxygen concentration was analyzed using a gas analyzer. The proposed optimal conditions include controlling the argon flow rate, liquid level, and the number of nozzles. It was established that an argon flow rate of 0.05–0.125 m³/min ensures effective protection of the melt, and an optimal flow opening angle of up to 3° contributes to efficiency levels of 92–99%. The obtained results are of significant practical importance for improving the tapping process, refining, and reducing steel oxidation. The developed dependencies allow for more accurate determination of blowing parameters and optimization of the tapping channel design, thereby enhancing the efficiency of metallurgical processes
- 26 December 2024
- Published by SHEI Pryazovskyi State Technical University in Reporter of the Priazovskyi State Technical University. Section: Technical sciences
- Vol. 1 (49) , 200-207
Open AccessStudy of the conditions of gas-liquid flow formation during the tapping of the melt from the converter
The study of the conditions for the formation of a gas-liquid flow during the tapping of molten metal from the converter is based on low-temperature modeling, aimed at analyzing the impact of the structural characteristics of the steel tapping channel. The use of inert gas (argon) enabled the creation of a protective gas shell that reduces the contact of the metal with atmospheric oxygen, lowering its content in the flow to 1–3%. Based on the experiments, a classification of blowing regimes and empirical dependencies were developed to describe the interaction between the gas and the liquid. It was established that the minimum oxygen concentration in the gas phase (1–3%) is achieved with an argon flow of 10–20% of the maximum. This maintains the efficiency of the protective shell at 95%. Further increases in the argon flow lead to the expansion of the flow's opening angle, negatively impacting its organization. Increasing the number of nozzles improves flow stability: with six nozzles, the oxygen concentration remains below 10.5%, even with high gas flow rates. Experiments on a flat tapping channel model revealed a dependence between the gas flow, liquid level, and the depth of the vortex. Increasing the gas flow with a high liquid level contributes to the stability of the interfacial surface, whereas reducing the liquid level leads to an increase in vortex depth and deterioration of the flow organization. The experiments were conducted on a laboratory setup simulating the tapping process, accounting for geometric and dynamic similarity. Technically pure argon with an oxygen content of up to 0.7% was used. The main parameters for analysis included gas flow rate, liquid level, relative vortex depth, and flow opening angle. To assess the effectiveness of the gas shell, oxygen concentration was analyzed using a gas analyzer. The proposed optimal conditions include controlling the argon flow rate, liquid level, and the number of nozzles. It was established that an argon flow rate of 0.05–0.125 m³/min ensures effective protection of the melt, and an optimal flow opening angle of up to 3° contributes to efficiency levels of 92–99%. The obtained results are of significant practical importance for improving the tapping process, refining, and reducing steel oxidation. The developed dependencies allow for more accurate determination of blowing parameters and optimization of the tapping channel design, thereby enhancing the efficiency of metallurgical processes
- Open Access
- 3 December 2024
- Published by Dniprovsk State Technical University in Collection of scholarly papers of Dniprovsk State Technical University (Technical Sciences)
- p. 98-110
REDUCTION OF IRON CONSUMPTION IN STEEL PRODUCTION IN CONVERTER SHOPS: MODERN APPROACHES AND SOLUTIONS
The article examines modern approaches and technological solutions aimed at reducing the cost of iron in the production of steel in converter shops. One of the key issues in the metallurgical industry is the optimization of raw material costs while simultaneously improving the quality of final products. In the conditions of growing competition on the market and increasing the cost of raw materials, the issue of reducing iron consumption in the steel production process becomes especially important. The purpose of the study is to substantiate effective technological methods of reducing the cost of cast iron while maintaining high technical and operational characteristics of steel. The work considers several directions for achieving this goal, in particular: improvement of the quality of raw materials through preliminary processing of scrap metal, modernization of converter equipment, optimization of oxygen purging modes, use of technologies of secondary processing of scrap metal, as well as the use of various technological additives and slag-forming materials. Special attention is paid to the possibilities of reducing energy consumption and increasing production efficiency through the use of scrap metal heating technologies.During the study, examples of the introduction of modern technologies at leading metallurgical enterprises, such as ArcelorMittal, ThyssenKrupp, Voestalpine and others, were considered. These technologies help to reduce the costs of raw materials and energy resources, which has a positive effect on the environmental indicators of production and the overall sustainability of metallurgical enterprises. An analysis of the use of carbon-containing materials, both in lump and powder forms, was also carried out to reduce the consumption of cast iron and increase the proportion of metal scrap in the metal charge. The question of the influence of such additives on the chemical composition of steel is considered. It was determined that the use of carbon-containing materials allows to significantly reduce the consumption of cast iron, however, it is necessary to take into account the influence of such factors as the composition of raw materials, the temperature in the converter and the parameters of adding carbon-containing materials during oxygen purging.The given results can be useful for enterprises of the metallurgical industry seeking to increase the efficiency of their production processes. The study demonstrates that the introduction of new technologies and approaches can provide a significant reduction in pig iron costs, increase the quality of steel and reduce the negative impact on the environment. The described methods have the potential for wide use in metallurgy, which will increase the competitiveness of Ukrainian enterprises on the international market.
- 3 December 2024
- Published by Dniprovsk State Technical University in Collection of scholarly papers of Dniprovsk State Technical University (Technical Sciences)
- p. 98-110
Open AccessREDUCTION OF IRON CONSUMPTION IN STEEL PRODUCTION IN CONVERTER SHOPS: MODERN APPROACHES AND SOLUTIONS
The article examines modern approaches and technological solutions aimed at reducing the cost of iron in the production of steel in converter shops. One of the key issues in the metallurgical industry is the optimization of raw material costs while simultaneously improving the quality of final products. In the conditions of growing competition on the market and increasing the cost of raw materials, the issue of reducing iron consumption in the steel production process becomes especially important. The purpose of the study is to substantiate effective technological methods of reducing the cost of cast iron while maintaining high technical and operational characteristics of steel. The work considers several directions for achieving this goal, in particular: improvement of the quality of raw materials through preliminary processing of scrap metal, modernization of converter equipment, optimization of oxygen purging modes, use of technologies of secondary processing of scrap metal, as well as the use of various technological additives and slag-forming materials. Special attention is paid to the possibilities of reducing energy consumption and increasing production efficiency through the use of scrap metal heating technologies.During the study, examples of the introduction of modern technologies at leading metallurgical enterprises, such as ArcelorMittal, ThyssenKrupp, Voestalpine and others, were considered. These technologies help to reduce the costs of raw materials and energy resources, which has a positive effect on the environmental indicators of production and the overall sustainability of metallurgical enterprises. An analysis of the use of carbon-containing materials, both in lump and powder forms, was also carried out to reduce the consumption of cast iron and increase the proportion of metal scrap in the metal charge. The question of the influence of such additives on the chemical composition of steel is considered. It was determined that the use of carbon-containing materials allows to significantly reduce the consumption of cast iron, however, it is necessary to take into account the influence of such factors as the composition of raw materials, the temperature in the converter and the parameters of adding carbon-containing materials during oxygen purging.The given results can be useful for enterprises of the metallurgical industry seeking to increase the efficiency of their production processes. The study demonstrates that the introduction of new technologies and approaches can provide a significant reduction in pig iron costs, increase the quality of steel and reduce the negative impact on the environment. The described methods have the potential for wide use in metallurgy, which will increase the competitiveness of Ukrainian enterprises on the international market.
- 3 December 2024
- Published by Dniprovsk State Technical University in Collection of scholarly papers of Dniprovsk State Technical University (Technical Sciences)
- p. 123-131
USE OF PULVERIZED COAL FUEL FOR PREHEATING SCRAP
Preheating of scrap in the converter is an actual area of research in modern metallurgy. The growing requirements for energy efficiency and the reduction of raw material costs encourage the development of new technological solutions to increase the share of scrap metal in the charge of converter production. Traditional methods are often limited to the use of no more than 25% of scrap, which is associated with difficulties in its uniform heating and the possible formation of a liquid phase as a result of local overheating. The work evaluates the effectiveness of traditional and experimental technological solutions, such as two-tier and fuel-oxygen nozzles. The stages of ignition and burning of lump coal and pulverized coal fuel and their influence on the uniformity of scrap heating were studied. Experimental studies have shown that with a specific oxygen consumption of 1-1.35 m³/kg of pulverized coal fuel, uniform heating of scrap metal is ensured without the risk of melting the upper layers. During the use of a fuel-oxygen lance, the following features of heating scrap metal using pulverized coal fuel, which was blown in an oxygen ring shell, were discovered: - during the combustion of coal dust in an oxygen environment, due to the significant total surface of coal particles, the bulk of volatile СmНn does not have time to separate before the beginning particle ignition, and carbon burns at the same rate as volatiles. This contributes to the formation of high-temperature torches with great luminosity, which effectively affect the surface of the scrap; - the coefficient of use of blown oxygen and pulverized coal fuel is significantly higher than when using lump gas coal during heating of any duration. This is due to the greater luminosity of the formed torches, which contributes to the intensive absorption of thermal energy by the surface of the scrap; - the time required to heat the surface of the scrap metal to the specified temperature is reduced, which allows you to avoid the formation of a liquid component that can lead to undesirable consequences, such as uneven heating or damage to the converter lining. Based on the results of experimental studies, the relationship between the specific oxygen consumption and the flame temperature was established. The ability to control the temperature regime during the heating of scrap metal indicates the prospects of using a fuel-oxygen nozzle made of PVP to optimize the converter production process. For the full implementation of the technology, additional research and industrial testing are needed to optimize processes and increase production efficiency.
- 3 December 2024
- Published by Dniprovsk State Technical University in Collection of scholarly papers of Dniprovsk State Technical University (Technical Sciences)
- p. 123-131
USE OF PULVERIZED COAL FUEL FOR PREHEATING SCRAP
Preheating of scrap in the converter is an actual area of research in modern metallurgy. The growing requirements for energy efficiency and the reduction of raw material costs encourage the development of new technological solutions to increase the share of scrap metal in the charge of converter production. Traditional methods are often limited to the use of no more than 25% of scrap, which is associated with difficulties in its uniform heating and the possible formation of a liquid phase as a result of local overheating. The work evaluates the effectiveness of traditional and experimental technological solutions, such as two-tier and fuel-oxygen nozzles. The stages of ignition and burning of lump coal and pulverized coal fuel and their influence on the uniformity of scrap heating were studied. Experimental studies have shown that with a specific oxygen consumption of 1-1.35 m³/kg of pulverized coal fuel, uniform heating of scrap metal is ensured without the risk of melting the upper layers. During the use of a fuel-oxygen lance, the following features of heating scrap metal using pulverized coal fuel, which was blown in an oxygen ring shell, were discovered: - during the combustion of coal dust in an oxygen environment, due to the significant total surface of coal particles, the bulk of volatile СmНn does not have time to separate before the beginning particle ignition, and carbon burns at the same rate as volatiles. This contributes to the formation of high-temperature torches with great luminosity, which effectively affect the surface of the scrap; - the coefficient of use of blown oxygen and pulverized coal fuel is significantly higher than when using lump gas coal during heating of any duration. This is due to the greater luminosity of the formed torches, which contributes to the intensive absorption of thermal energy by the surface of the scrap; - the time required to heat the surface of the scrap metal to the specified temperature is reduced, which allows you to avoid the formation of a liquid component that can lead to undesirable consequences, such as uneven heating or damage to the converter lining. Based on the results of experimental studies, the relationship between the specific oxygen consumption and the flame temperature was established. The ability to control the temperature regime during the heating of scrap metal indicates the prospects of using a fuel-oxygen nozzle made of PVP to optimize the converter production process. For the full implementation of the technology, additional research and industrial testing are needed to optimize processes and increase production efficiency.
- Open Access
- 3 December 2024
- Published by Dniprovsk State Technical University in Collection of scholarly papers of Dniprovsk State Technical University (Technical Sciences)
- p. 132-137
MATHEMATICAL MODEL OF METAL SCRAP HEATING IN THE CONVERTER WITH A COAL TORCH
Increasing requirements for energy efficiency and the level of competitiveness of domestic metal products led to the development of new technological solutions to increase the share of scrap metal in the charge of oxygen-converter melting. Data on temperature distribution in the working space of the converter and in the layer of scrap metal during its pre-heating using standard oxygen or special fuel-oxygen nozzles are limited and do not go beyond the scope of scientific assumptions. The results of numerous simulations of the process of heating metal scrap in the working space of an oxygen converter with a high-temperature torch formed by burning pulverized coal fuel in an oxygen stream using a fuel-oxygen nozzle are presented. A mathematical model of heating scrap metal in the working space of the converter with a pulverized coal torch was built and its software implementation has been done in the Visual Studio 2022 environment in the C# language. With the help of the model, a series of RO-calculations was carried out, which proved its qualitative adequacy of the process under consideration. The results of the calculation with the determination of the fields of velocities and temperatures in the working space of the converter during the heating of scrap metal are presented. It was established that the direction of heat transfer is determined by gas flows caused by a high-temperature torch. Upon reaching the metal scrap, the gas flows lead to its gradual heating, which generally corresponds to the qualitative picture of the simulated process.The dependence of the distribution of gas flows on the shape of the surface of the scrap loaded into the converter is shown. It was established that local vortices can form in the depths of the scrap surface during heating by a high-temperature torch. But the general characteristic of the gas-dynamic picture in the working space of the converter is the formation of two global vortices: one near the torch with counterclockwise rotation (in the sections shown), and the other clockwise with the formation of downward gas flows near the inner surface of the converter. These vortices mainly determine the thermal pattern in the working space of the converter and, in particular, the fact that the scrap near the wall of the converter will warm up less.
- 3 December 2024
- Published by Dniprovsk State Technical University in Collection of scholarly papers of Dniprovsk State Technical University (Technical Sciences)
- p. 132-137
Open AccessMATHEMATICAL MODEL OF METAL SCRAP HEATING IN THE CONVERTER WITH A COAL TORCH
Increasing requirements for energy efficiency and the level of competitiveness of domestic metal products led to the development of new technological solutions to increase the share of scrap metal in the charge of oxygen-converter melting. Data on temperature distribution in the working space of the converter and in the layer of scrap metal during its pre-heating using standard oxygen or special fuel-oxygen nozzles are limited and do not go beyond the scope of scientific assumptions. The results of numerous simulations of the process of heating metal scrap in the working space of an oxygen converter with a high-temperature torch formed by burning pulverized coal fuel in an oxygen stream using a fuel-oxygen nozzle are presented. A mathematical model of heating scrap metal in the working space of the converter with a pulverized coal torch was built and its software implementation has been done in the Visual Studio 2022 environment in the C# language. With the help of the model, a series of RO-calculations was carried out, which proved its qualitative adequacy of the process under consideration. The results of the calculation with the determination of the fields of velocities and temperatures in the working space of the converter during the heating of scrap metal are presented. It was established that the direction of heat transfer is determined by gas flows caused by a high-temperature torch. Upon reaching the metal scrap, the gas flows lead to its gradual heating, which generally corresponds to the qualitative picture of the simulated process.The dependence of the distribution of gas flows on the shape of the surface of the scrap loaded into the converter is shown. It was established that local vortices can form in the depths of the scrap surface during heating by a high-temperature torch. But the general characteristic of the gas-dynamic picture in the working space of the converter is the formation of two global vortices: one near the torch with counterclockwise rotation (in the sections shown), and the other clockwise with the formation of downward gas flows near the inner surface of the converter. These vortices mainly determine the thermal pattern in the working space of the converter and, in particular, the fact that the scrap near the wall of the converter will warm up less.
- Open Access
- 25 December 2023
- Published by Dniprovsk State Technical University in Collection of scholarly papers of Dniprovsk State Technical University (Technical Sciences)
- Vol. 2 (43) , 9-17
OPERATING CONDITIONS AND STABILITY FIRE RESISTANT LINING SUBMERGED LANCE
To ensure the reliable and long—term operation of submersible lances used in the processes of bucket desulfurization of cast iron before converter processing, reliable means and appropriate conditions for supplying powdered desulfurizing reagents through nozzles of the lance tip, a rational scheme of refractory lining of the submersible lance and improvement of its operation modes are necessary. The purpose of the work is to study the characteristics of the destruction of the refractory lining of submersible lances, intended for desulfurization of iron—carbon melts by blowing powdery reagents deep into the ladle bath. To realize the goal, we used practical information on the researched question and the method of isothermal modeling of the hydrogas dynamics of a bucket bath using variable designs of the tips of stationary and rotating submersible lances. A comparative analysis and study of the features of the destruction of the lining of submerged stationary and rotating lances in the area of contact with the metal melt (below the "slag—metal" border) during gas injection into the bath was carried out using a 230—t pouring ladle model. During the experiments, T—shaped tips were used (for rotating and stationary lances) and tips with two spray pipe placed at an angle of 45 degrees to the axis of the lance (for stationary lances). Based on the results of data processing, mathematical models were obtained for each of the isolated zones on the lining surface of the submersible lance, and the statistical significance of the sample regression coefficients was checked. The nature and features of the destruction of the lining layer in each of the zones corresponding to the changes in the bath blowing conditions were established. New data were obtained regarding the intensity and depth of wear of the lining of the rotating submersible lance, depending on its speed of rotation and carrier gas consumption. It was established that under the investigated conditions of blowing the bath, the speed of rotation of the lance can be attributed to the factor most influencing the depth and intensity of wear of the lance lining.
- 25 December 2023
- Published by Dniprovsk State Technical University in Collection of scholarly papers of Dniprovsk State Technical University (Technical Sciences)
- Vol. 2 (43) , 9-17
Open AccessOPERATING CONDITIONS AND STABILITY FIRE RESISTANT LINING SUBMERGED LANCE
To ensure the reliable and long—term operation of submersible lances used in the processes of bucket desulfurization of cast iron before converter processing, reliable means and appropriate conditions for supplying powdered desulfurizing reagents through nozzles of the lance tip, a rational scheme of refractory lining of the submersible lance and improvement of its operation modes are necessary. The purpose of the work is to study the characteristics of the destruction of the refractory lining of submersible lances, intended for desulfurization of iron—carbon melts by blowing powdery reagents deep into the ladle bath. To realize the goal, we used practical information on the researched question and the method of isothermal modeling of the hydrogas dynamics of a bucket bath using variable designs of the tips of stationary and rotating submersible lances. A comparative analysis and study of the features of the destruction of the lining of submerged stationary and rotating lances in the area of contact with the metal melt (below the "slag—metal" border) during gas injection into the bath was carried out using a 230—t pouring ladle model. During the experiments, T—shaped tips were used (for rotating and stationary lances) and tips with two spray pipe placed at an angle of 45 degrees to the axis of the lance (for stationary lances). Based on the results of data processing, mathematical models were obtained for each of the isolated zones on the lining surface of the submersible lance, and the statistical significance of the sample regression coefficients was checked. The nature and features of the destruction of the lining layer in each of the zones corresponding to the changes in the bath blowing conditions were established. New data were obtained regarding the intensity and depth of wear of the lining of the rotating submersible lance, depending on its speed of rotation and carrier gas consumption. It was established that under the investigated conditions of blowing the bath, the speed of rotation of the lance can be attributed to the factor most influencing the depth and intensity of wear of the lance lining.