Jiadong Shen
Research Subjects
Jiadong Shen has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Lin-Yuan Bai
Field Engineering College, Army Engineering University of PLA, Nanjing 210007, China
2 shared publications - Shengli Song
College of Mechanical Engineering Yancheng Institute of Technology Yancheng China
2 shared publications - Xiaolong Wang2 shared publications
Binning Peng
1 shared publication- Shengli Song1 shared publication
- Shuangyu Liu
College of Mechanical Engineering Yancheng Institute of Technology Yancheng China
1 shared publication
Latest Publications
- Open Access
- 5 May 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of SiC Content on the Microstructure and High-Temperature Tribological Properties of Laser-Cladded AlCoCrFeNi Coatings
In this study, SiC nanoparticle-reinforced AlCoCrFeNi high-entropy alloy composite coatings (AlCoCrFeNi + x wt% SiC, x = 0, 10, 20, and 30) were fabricated on 316L stainless steel substrates by laser cladding. Their high temperature tribological behavior was systematically investigated under dry sliding conditions at 600 ℃ and 800 ℃. Among the tested coatings, the coating containing 20 wt% SiC exhibited the best overall tribological performance, with average friction coefficients of 0.28 and 0.40 and wear volumes of 0.3997 mm³ and 0.1575 mm³ at 600 ℃ and 800 ℃, respectively. These wear volumes correspond to reductions of 60.91% and 78.32% compared with the SiC-free coating.The corresponding wear rates were 8.65×10⁻⁵ and 3.41×10⁻⁵ mm³/(N·m). Microhardness measurements indicate that SiC addition improves the load-bearing capability of the coating, whereas excessive SiC increases brittleness and promotes spallation. Multi-scale characterizations suggest that the superior performance of the 20 wt% SiC coating is associated with the formation of a relatively continuous tribo-reaction layer composed mainly of Cr–Fe-rich oxides together with Si–O-related species. In addition, a heterogeneous subsurface structure consisting of Cr-enriched banded regions and Ni/Al-enriched island-like regions was observed after sliding at 800 ℃, which is likely related to enhanced shear accommodation and load support. These results indicate that an appropriate SiC content can improve the high-temperature tribological performance of laser-cladded AlCoCrFeNi coatings by stabilizing the interfacial reaction layer and reducing material removal.
- 5 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of SiC Content on the Microstructure and High-Temperature Tribological Properties of Laser-Cladded AlCoCrFeNi Coatings
In this study, SiC nanoparticle-reinforced AlCoCrFeNi high-entropy alloy composite coatings (AlCoCrFeNi + x wt% SiC, x = 0, 10, 20, and 30) were fabricated on 316L stainless steel substrates by laser cladding. Their high temperature tribological behavior was systematically investigated under dry sliding conditions at 600 ℃ and 800 ℃. Among the tested coatings, the coating containing 20 wt% SiC exhibited the best overall tribological performance, with average friction coefficients of 0.28 and 0.40 and wear volumes of 0.3997 mm³ and 0.1575 mm³ at 600 ℃ and 800 ℃, respectively. These wear volumes correspond to reductions of 60.91% and 78.32% compared with the SiC-free coating.The corresponding wear rates were 8.65×10⁻⁵ and 3.41×10⁻⁵ mm³/(N·m). Microhardness measurements indicate that SiC addition improves the load-bearing capability of the coating, whereas excessive SiC increases brittleness and promotes spallation. Multi-scale characterizations suggest that the superior performance of the 20 wt% SiC coating is associated with the formation of a relatively continuous tribo-reaction layer composed mainly of Cr–Fe-rich oxides together with Si–O-related species. In addition, a heterogeneous subsurface structure consisting of Cr-enriched banded regions and Ni/Al-enriched island-like regions was observed after sliding at 800 ℃, which is likely related to enhanced shear accommodation and load support. These results indicate that an appropriate SiC content can improve the high-temperature tribological performance of laser-cladded AlCoCrFeNi coatings by stabilizing the interfacial reaction layer and reducing material removal.
- Open Access
- 23 April 2026
- Published by Elsevier in SSRN Electronic Journal
Strengthening mechanism of CeO2 on the high-temperature friction and wear performance of laser-cladded AlCoCrFeNi high-entropy alloy
AlCoCrFeNi high-entropy alloy coatings reinforced with CeO₂ were fabricated on 316L stainless steel via laser cladding to enhance high-temperature tribological performance. A data-assisted approach combining chemical descriptors with a support vector regression model was used to predict the optimal CeO₂ content based on wear-related indicators. The model identified an optimal content of 2.96 wt%, which was validated by experiments at 600 °C and 800 °C. The results show that CeO₂ addition refines the microstructure, promotes grain boundary pinning, and facilitates the formation of dense Cr₂O₃- and Fe₂O₃-rich tribo-oxide films. The coating with 2.96 wt% CeO₂ exhibits the lowest friction coefficient, with wear-track width reduced by 44.0% and 47.0% and wear depth decreased by 19.0% and 57.9% at 600 °C and 800 °C, respectively, compared with the CeO₂-free coating. The dominant wear mechanism shifts from adhesive wear to mild abrasive wear. Microstructural analysis reveals the formation of a nanocrystalline subsurface layer and the evolution of dislocations from tangles to stable walls, indicating enhanced structural stability. The improved performance is attributed to the synergistic effect of grain refinement and stabilized tribo-oxide films. This study provides a data-guided strategy for optimizing rare-earth-modified HEA coatings for high-temperature applications.
- 23 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessStrengthening mechanism of CeO2 on the high-temperature friction and wear performance of laser-cladded AlCoCrFeNi high-entropy alloy
AlCoCrFeNi high-entropy alloy coatings reinforced with CeO₂ were fabricated on 316L stainless steel via laser cladding to enhance high-temperature tribological performance. A data-assisted approach combining chemical descriptors with a support vector regression model was used to predict the optimal CeO₂ content based on wear-related indicators. The model identified an optimal content of 2.96 wt%, which was validated by experiments at 600 °C and 800 °C. The results show that CeO₂ addition refines the microstructure, promotes grain boundary pinning, and facilitates the formation of dense Cr₂O₃- and Fe₂O₃-rich tribo-oxide films. The coating with 2.96 wt% CeO₂ exhibits the lowest friction coefficient, with wear-track width reduced by 44.0% and 47.0% and wear depth decreased by 19.0% and 57.9% at 600 °C and 800 °C, respectively, compared with the CeO₂-free coating. The dominant wear mechanism shifts from adhesive wear to mild abrasive wear. Microstructural analysis reveals the formation of a nanocrystalline subsurface layer and the evolution of dislocations from tangles to stable walls, indicating enhanced structural stability. The improved performance is attributed to the synergistic effect of grain refinement and stabilized tribo-oxide films. This study provides a data-guided strategy for optimizing rare-earth-modified HEA coatings for high-temperature applications.