Yakun Li
Research Subjects
Yakun Li has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Hyung Doh Roh
Hanyang University ERICA
2 shared publications Gyu-Hwa Lee
1 shared publicationHaochen Gao
1 shared publicationSang-Ha Hwang
1 shared publicationWoo-Cheol Jang
1 shared publicationYoung-Jin Shim
1 shared publication
Latest Publications
- Open Access
- 11 September 2026
- Published by Elsevier in SSRN Electronic Journal
Analysis of Thermal Expansion and Torsional Behavior of FDM Additively Manufactured Polyethersulfone and Carbon Fiber-Reinforced Polyethersulfone Composites for Wind Turbine Blade Molds
This study investigates the thermal expansion and torsional behavior of polyethersulfone (PES), and carbon fiber reinforced PES composites fabricated by fused deposition modeling (FDM) for high temperature vacuum assisted resin infusion tooling. Three material systems, neat PES, chopped carbon fiber reinforced PES and milled carbon fiber reinforced PES, were examined with unidirectional [UD], [0/90] and [0/45/90/135] stacking configurations. Experiments conducted in an oven measured thermal deformation, Classical Laminate Plate Theory (CLPT) explained stacking effects on bending and torsion, and three-dimensional finite element analysis (FEA) in ANSYS quantified deformation and torsion. In the oven experiment, carbon fiber reinforcement strongly reduced in plane thermal strain: CCF PES and MCF PES showed in plane strains approximately 26 to 38% of neat PES, while through thickness strains remained similar. In FEA, CCF PES reduced in plane thermal strain by approximately 60% and through thickness strain by 40 to 45% relative to PES. Torsion angle, calculated from Z directional deformation along the top edge, was essentially zero for [UD] and [0/90], while [0/45/90/135] produced 0.0035° (PES) and 0.0014° (CCF PES). CLPT and FEA agreed closely, with CCF PES showing approximately 58.5% (CLPT) and 60% (FEA) lower torsion angle than PES for [0/45/90/135]. Asymmetric stacking and geometry further increased the torsion angle. The wind turbine blade mold showed the same reinforcement trend, with [0/45/90/135] producing 0.0026° (PES) and 0.0011° (CCF PES). These results indicate that stacking configuration governs the occurrence of torsion, and carbon fiber reinforcement reduces both directional thermal strain and torsional deformation magnitude.
- 11 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAnalysis of Thermal Expansion and Torsional Behavior of FDM Additively Manufactured Polyethersulfone and Carbon Fiber-Reinforced Polyethersulfone Composites for Wind Turbine Blade Molds
This study investigates the thermal expansion and torsional behavior of polyethersulfone (PES), and carbon fiber reinforced PES composites fabricated by fused deposition modeling (FDM) for high temperature vacuum assisted resin infusion tooling. Three material systems, neat PES, chopped carbon fiber reinforced PES and milled carbon fiber reinforced PES, were examined with unidirectional [UD], [0/90] and [0/45/90/135] stacking configurations. Experiments conducted in an oven measured thermal deformation, Classical Laminate Plate Theory (CLPT) explained stacking effects on bending and torsion, and three-dimensional finite element analysis (FEA) in ANSYS quantified deformation and torsion. In the oven experiment, carbon fiber reinforcement strongly reduced in plane thermal strain: CCF PES and MCF PES showed in plane strains approximately 26 to 38% of neat PES, while through thickness strains remained similar. In FEA, CCF PES reduced in plane thermal strain by approximately 60% and through thickness strain by 40 to 45% relative to PES. Torsion angle, calculated from Z directional deformation along the top edge, was essentially zero for [UD] and [0/90], while [0/45/90/135] produced 0.0035° (PES) and 0.0014° (CCF PES). CLPT and FEA agreed closely, with CCF PES showing approximately 58.5% (CLPT) and 60% (FEA) lower torsion angle than PES for [0/45/90/135]. Asymmetric stacking and geometry further increased the torsion angle. The wind turbine blade mold showed the same reinforcement trend, with [0/45/90/135] producing 0.0026° (PES) and 0.0011° (CCF PES). These results indicate that stacking configuration governs the occurrence of torsion, and carbon fiber reinforcement reduces both directional thermal strain and torsional deformation magnitude.