Xiang Li
Research Subjects
Xiang Li has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Hiroshi Utsunomiya
Division of Materials and Manufacturing Science, Graduate School of Engineering, The University of Osaka
2 shared publications - Ken-Ichi Saitoh
Kansai University
2 shared publications - Ryo Matsumoto
Division of Materials and Manufacturing Science, Osaka University, Suita, Japan
2 shared publications - Shigenobu Ogata
Department of Mechanical Science and Bioengineering Graduate School of Engineering Science Osaka University 1-3 Machikaneyama 560-8531 Toyonaka Osaka Japan
2 shared publications Shuhei Shinzato
1 shared publication- Shuhei Shinzato
Department of Mechanical Science and Bioengineering, Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531, Japan
1 shared publication
Latest Publications
- Open Access
- 4 November 2026
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 745
Sensitivity of MD-based Taylor-Quinney coefficient estimates to thermodynamic ensemble and defect preconditioning
- 4 November 2026
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 745
Open AccessSensitivity of MD-based Taylor-Quinney coefficient estimates to thermodynamic ensemble and defect preconditioning
- Open Access
- 14 May 2026
- Published by Elsevier in SSRN Electronic Journal
Taylor-Quinney Coefficient Analysis using Molecular Dynamics- Effects of Thermodynamic Ensembles -
Accurate measurement of heat generation from plastic deformation work, i.e. the Taylor-Quinney coefficient (TQC: ), is difficult because heat conduction and thermal expansion can disturb the heat balance during deformation. Quantitative numerical analysis of TQC is therefore useful. Molecular dynamics (MD) simulation is a promising numerical method because the heat balance can be clearly measured. This work examines the influence of thermodynamic ensembles on MD-based TQC analysis in simple shear deformation of single-crystalline aluminium. To use a simple crystalline model while representing the pre-existing defects usually present in real materials, a three-stage deformation procedure, here denoted as Pre-Hold-Deform (P-H-D), was adopted. A pre-deformation and subsequent unloading/holding step introduce a stable defect-conditioned state before the deformation used for TQC evaluation, thereby reducing the influence of stress overshoot caused by homogeneous defect nucleation from an unrealistically defect-free crystal. TQC was calculated as the ratio of heat generation to plastic work, with the heat and work balances evaluated under NVE, NVT, NPH and NPT ensembles. The results show that, under the present conditions, the evaluated TQC under isochoric conditions (NVE or NVT) are larger than TQC under isobaric conditions (NPH or NPT). The comparison of ensembles provides useful guidance for assessing how thermal and mechanical boundary conditions affect TQC analysis.
- 14 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessTaylor-Quinney Coefficient Analysis using Molecular Dynamics- Effects of Thermodynamic Ensembles -
Accurate measurement of heat generation from plastic deformation work, i.e. the Taylor-Quinney coefficient (TQC: ), is difficult because heat conduction and thermal expansion can disturb the heat balance during deformation. Quantitative numerical analysis of TQC is therefore useful. Molecular dynamics (MD) simulation is a promising numerical method because the heat balance can be clearly measured. This work examines the influence of thermodynamic ensembles on MD-based TQC analysis in simple shear deformation of single-crystalline aluminium. To use a simple crystalline model while representing the pre-existing defects usually present in real materials, a three-stage deformation procedure, here denoted as Pre-Hold-Deform (P-H-D), was adopted. A pre-deformation and subsequent unloading/holding step introduce a stable defect-conditioned state before the deformation used for TQC evaluation, thereby reducing the influence of stress overshoot caused by homogeneous defect nucleation from an unrealistically defect-free crystal. TQC was calculated as the ratio of heat generation to plastic work, with the heat and work balances evaluated under NVE, NVT, NPH and NPT ensembles. The results show that, under the present conditions, the evaluated TQC under isochoric conditions (NVE or NVT) are larger than TQC under isobaric conditions (NPH or NPT). The comparison of ensembles provides useful guidance for assessing how thermal and mechanical boundary conditions affect TQC analysis.