Jakub Oprsal
Research Subjects
Jakub Oprsal has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Claudia M. Rocha
Smallmatek—Small Materials and Technologies, Lda, Rua dos Canhas, 3810-075 Aveiro, Portugal
1 shared publication - Cristina S. Neves
DEMaC-Aveiro Institute of Materials, University of Aveiro, Campus Universitário de Santiago, 3810-193 Aveiro, Portugal
1 shared publication - Daiva Zeleniakiene
Department of Mechanical Engineering Kaunas University of Technology Kaunas Lithuania
1 shared publication - Eliška Juhaňáková
Institute of Technology and Business in České Budějovice, Okružní 517/10, České Budějovice, 37001, Czech Republichttps://ror.org/05a70k539https://www.isni.org/isni
1 shared publication - Filip Bureš
Institute of Organic Chemistry and Technology, Faculty of Chemical Technology, University of Pardubice, Studentská 573, Pardubice, 53210, Czech Republic
1 shared publication - Jan Podlesný
Institute of Technology and Business in České Budějovice, Okružní 517/10, České Budějovice, 37001, Czech Republichttps://ror.org/05a70k539https://www.isni.org/isni
1 shared publication
Latest Publications
- Open Access
Epoxy/Layered Double Hydroxide Nanocomposites: Investigating the Influence of Preparation Method on Mechanical Properties
This study investigates the macro- and micromechanical properties of epoxy-based nanocomposites containing Mg-Al/NO3 layered double hydroxides (LDHs), with a comparative evaluation of two preparation routes: solvent exchange and direct drying from an aqueous LDH slurry. LDHs were characterised using atomic force microscopy (AFM), scanning transmission electron microscopy, and X-ray diffraction methods. Tensile tests and AFM nanomechanical mapping were used to obtain the macro- and micromechanical properties of LDH/epoxy nanocomposites, respectively. Both preparation methods resulted in nanocomposites with comparable mechanical performance. Young’s modulus increased by approximately 30–70% at lower LDH loadings (1–2 wt.%), and the ultimate tensile strength remained largely unchanged compared to pure epoxy. At higher LDH contents, tensile strength decreased by approximately 15–26%, while fracture strain decreased by up to 54%, which was attributed to particle aggregation, as confirmed by scanning electron microscopy and energy-dispersive X-ray spectroscopy. The mechanical response and stiffness maps obtained by the peak force AFM nanomechanical mapping revealed that nanocomposites prepared using solvent-exchanged LDHs exhibit significantly narrower interfacial widths and higher stiffness compared to those made by the conventional approach, indicating improved interfacial bonding and mechanical performance. Overall, the solvent-exchange approach proved effective for improving the interfacial properties and stiffness of epoxy/LDH nanocomposites.
Open AccessEpoxy/Layered Double Hydroxide Nanocomposites: Investigating the Influence of Preparation Method on Mechanical Properties
This study investigates the macro- and micromechanical properties of epoxy-based nanocomposites containing Mg-Al/NO3 layered double hydroxides (LDHs), with a comparative evaluation of two preparation routes: solvent exchange and direct drying from an aqueous LDH slurry. LDHs were characterised using atomic force microscopy (AFM), scanning transmission electron microscopy, and X-ray diffraction methods. Tensile tests and AFM nanomechanical mapping were used to obtain the macro- and micromechanical properties of LDH/epoxy nanocomposites, respectively. Both preparation methods resulted in nanocomposites with comparable mechanical performance. Young’s modulus increased by approximately 30–70% at lower LDH loadings (1–2 wt.%), and the ultimate tensile strength remained largely unchanged compared to pure epoxy. At higher LDH contents, tensile strength decreased by approximately 15–26%, while fracture strain decreased by up to 54%, which was attributed to particle aggregation, as confirmed by scanning electron microscopy and energy-dispersive X-ray spectroscopy. The mechanical response and stiffness maps obtained by the peak force AFM nanomechanical mapping revealed that nanocomposites prepared using solvent-exchanged LDHs exhibit significantly narrower interfacial widths and higher stiffness compared to those made by the conventional approach, indicating improved interfacial bonding and mechanical performance. Overall, the solvent-exchange approach proved effective for improving the interfacial properties and stiffness of epoxy/LDH nanocomposites.
- Open Access
- 21 May 2026
- Published by Beilstein Institut in Beilstein Journal of Organic Chemistry
- Vol. 22, 782-794
Halogenated azobenzene acrylates: from efficient solution photoswitching to stable solid-state photochromic materials
The design, synthesis, and comprehensive characterization of six novel halogenated azobenzene acrylate monomers bearing fluorine, chlorine or bromine substituents is reported. The monomers were prepared via a facile three-step synthetic route involving azo-coupling, O- alkylation and O -acylation. Apart from the steady electrochemical properties, halogen substitution proved to be a very useful tool to tune the thermal and optical properties, light-induced switching in particular. Monohalogen derivatives exhibited up to 93% E → Z photoconversion efficiency in solution, whereas the efficiency of dihalogen analogues is lower by 20%, which is ascribed to their nonplanar arrangement. Kinetics studies identified the most stable Z -isomer of the difluoro derivative ( τ 1/2 = 3.74/6.59 h at 60 °C in DCE/CDCl 3 ). The monofluoro derivative embedded in a polystyrene film demonstrated photoresponsive behavior and remarkable stability by maintaining a macroscopically visible color change for over 90 days. These findings demonstrate that ortho -halogenation is a powerful tool for tuning the properties of photoresponsive materials for potential applications in colorimetric thermal sensing and light-controlled functional systems.
- 21 May 2026
- Published by Beilstein Institut in Beilstein Journal of Organic Chemistry
- Vol. 22, 782-794
Open AccessHalogenated azobenzene acrylates: from efficient solution photoswitching to stable solid-state photochromic materials
The design, synthesis, and comprehensive characterization of six novel halogenated azobenzene acrylate monomers bearing fluorine, chlorine or bromine substituents is reported. The monomers were prepared via a facile three-step synthetic route involving azo-coupling, O- alkylation and O -acylation. Apart from the steady electrochemical properties, halogen substitution proved to be a very useful tool to tune the thermal and optical properties, light-induced switching in particular. Monohalogen derivatives exhibited up to 93% E → Z photoconversion efficiency in solution, whereas the efficiency of dihalogen analogues is lower by 20%, which is ascribed to their nonplanar arrangement. Kinetics studies identified the most stable Z -isomer of the difluoro derivative ( τ 1/2 = 3.74/6.59 h at 60 °C in DCE/CDCl 3 ). The monofluoro derivative embedded in a polystyrene film demonstrated photoresponsive behavior and remarkable stability by maintaining a macroscopically visible color change for over 90 days. These findings demonstrate that ortho -halogenation is a powerful tool for tuning the properties of photoresponsive materials for potential applications in colorimetric thermal sensing and light-controlled functional systems.