Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Eray Tabak has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Tailoring Sensitivity and Selectivity with Nanoparticle-Functionalized ZnO Nanorods: The Impact of Metals on Sensing and Electrical Performance

    by Eray Tabak, Sadullah Öztürk, Arif Kösemen, Necmettin Kılınç, Zafer Ziya Öztürk

    In this study, metal (copper, nickel, cobalt, chromium)-decorated ZnO nanorods are successfully grown on glass substrates via a hydrothermal synthesis method to test their electrical and gas-sensing properties. SEM images revealed the formation of metal nanoparticles surrounding the ZnO nanorods. To confirm that these structures originated from the metal nanoparticles, EDX analysis was performed, and the presence of metal nanoparticles was validated. XRD analysis indicated that the crystal structure of the ZnO nanorods was hexagonal, and shifts in the (002) plane were observed due to metal nanoparticle doping. ZnO nanorods functionalized with metal nanoparticles were tested at 200 °C against various gases (hydrogen, ethanol, chloroform) and at different gas concentrations. The time-dependent variation in current was observed when ZnO nanorods functionalized with metal elements were exposed to hydrogen gas at test concentrations ranging from 1000 ppm to 5000 ppm at 200 °C. The results demonstrated a clear correlation between the rate of current change and hydrogen concentration, with higher concentrations resulting in faster responses. Additionally, the sensitivity of ZnO nanorods with decorated metal nanoparticles to ethanol and chloroform gases at concentrations ranging from 1000 ppm to 5000 ppm, as well as their sensor responses to different gases at 200 °C, were also measured.

  • Open Access

    Enhanced Photocatalytic and Electrical Performance of Boron-Doped ZnO Nanorods: A Taguchi Optimization Approach for Degradation Efficiency

    by Eray Tabak, Sadullah Öztürk, Arif Kösemen, Şahika Sena Bayazi̇t, Necmettin Kılınç, Mika Sillanpää, Birgül Benli̇

    In this study, the development of boron-doped zinc oxide nanorods (B-ZnO NRs) as an innovative photocatalyst for the degradation of organic pollutants under UV-A light was investigated. ZnO NRs, doped with varying concentrations of boron, were synthesized via a hydrothermal method, and their structural, optical, electrical, and photocatalytic properties were systematically characterized. The photocatalytic performance of B-ZnO NRs was evaluated under varying pH conditions, contaminant concentrations, and reaction times, while their electrical properties were analyzed by examining the conduction mechanism using the Arrhenius and Mott variable range hopping (VRH) conduction models. Results indicated that boron doping altered the conduction mechanism of ZnO as predicted by these models. In addition, boron doping enhanced electrical conductivity, with DC conductivity increasing up to 5-fold and alternating current conductivity by 3-fold compared to undoped ZnO. A significant enhancement in photocatalytic efficiency was observed, with B-ZnO exhibiting up to 140% higher degradation efficiency at pH 10 compared to pure ZnO. In addition, a Taguchi statistical optimization approach was employed to identify the most influential parameters affecting photocatalytic performance, including pH, reaction time, contaminant concentration, and boron doping levels. Optimal conditions were determined to be pH 10, a contaminant concentration of 2 μM, a reaction time of 90 min, and a boron doping level of 7%. Boron doping significantly improved the photocatalytic activity of ZnO nanorods, making them a promising candidate for advanced water treatment, hydrogen production, and environmental sensing applications.

  • Open Access

    Production, Optimization and Characterization of Polylactic Acid Microparticles Using Electrospray with Porous Structure

    by Muhammed Enes Tasci, Berna Dede, Eray Tabak, Aybuke Gur, Rabia Betul Sulutas, Sumeyye Cesur, Elif Ilhan, Chi-Chang Lin, Pradip Paik, Denisa Ficai, et al.

    Polymeric microparticles with controlled morphologies and sizes are being studied by researchers in many applications, such as for drug release, healthcare and cosmetics. Herein, spherical and porous polymeric microparticles of different sizes and morphologies by electrospray technique have been developed as a viable alternative. In this work, polylactic acid (PLA) microparticles with a spherical shape and porous morphology were successfully produced via an electrospray technique in a single step. Molecular interactions between the components and the effect of parameters, such as varying solvent compositions, flow rates and voltage on microparticle morphology, were investigated over the particle formation. It was observed that the type of solvents used is the most effective parameter in terms of particle morphology, size and distribution. When the optical microscopy and SEM images of the microparticles were examined, 3 wt.% PLA in dichloromethane (DCM) solution concentration with an applied voltage of 18 kV and a flow rate of 20 µL/min was found to be the optimum parameter combination to achieve the desired spherical and porous micron-size particles. The average diameter of the particles achieved was 3.01 ± 0.58 µm. DCM was found to be a more suitable solvent for obtaining microparticles compared to the other solvents used. Finally, particles that are obtained by electrospraying of PLA–DCM solution are porous and monodisperse. They might have excellent potential as a carrier of drugs to the targeted sides and can be used in different biomedical applications.