Aphichon Mungchu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aphichon Mungchu has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Kumpanat Chaiphet
5 shared publications- Nattadon Pannucharoenwong
Thammasat University
5 shared publications Phadungsak Ratanadecho
5 shared publicationsSnunkhaem Echaroj
5 shared publicationsTanatorn Tanantong
5 shared publicationsKeyoon Duanguppama
3 shared publications
Latest Publications
- Open Access
- 25 September 2026
- Published by Elsevier in SSRN Electronic Journal
Thermohydraulic performance of turbulent flow in a circular tube with opposed parabolic V-winglets: coupled effects of pitch, blockage, and attack angle
Opposed parabolic V–winglets (PVWs) are evaluated as passive longitudinal-vortex generators for enhancing convection in circular tubes. Three–dimensional steady Reynolds averaged simulations were performed for turbulent air flow through a uniformly heated tube containing opposed PVWs on a central tape. Pitch ratio (PR) = 0.5–2.0, blockage ratio (BR)= 0.1– 0.5, attack angle (α) = 30°–60°, and Reynolds number (Re) = 3000–24,000 were varied under a uniform wall heat flux of 600 W m⁻². The realizable k-ε model was used to resolve turbulent kinetic energy, wall-temperature fields, local heat transfer, and global thermohydraulic performance. The inserts generated counter-rotating streamwise vortices, walldirected jets, separation and reattachment, and repeated thermal-boundary-layer renewal. The Nusselt-number ratio (Nu/Nu0) and Darcy friction factor ratio (f/f0) were 1.396–7.901 and 2.590–140.673, respectively. Although heat transfer increased with BR and decreasing PR, the pressure-loss penalty rose nonlinearly. The thermal enhancement factor (TEF) ranged from 0.531 to 2.327 and generally decreased with Re. The maximum TEF of 2.327 occurred at BR = 0.2, PR = 0.5, α = 30°, and Re = 3000, whereas the maximum Nu/Nu0 occurred at BR = 0.5 and α = 45°. Thus, moderate blockage and close spacing provide a better equal pumping power compromise than the most obstructive geometry.
- 25 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessThermohydraulic performance of turbulent flow in a circular tube with opposed parabolic V-winglets: coupled effects of pitch, blockage, and attack angle
Opposed parabolic V–winglets (PVWs) are evaluated as passive longitudinal-vortex generators for enhancing convection in circular tubes. Three–dimensional steady Reynolds averaged simulations were performed for turbulent air flow through a uniformly heated tube containing opposed PVWs on a central tape. Pitch ratio (PR) = 0.5–2.0, blockage ratio (BR)= 0.1– 0.5, attack angle (α) = 30°–60°, and Reynolds number (Re) = 3000–24,000 were varied under a uniform wall heat flux of 600 W m⁻². The realizable k-ε model was used to resolve turbulent kinetic energy, wall-temperature fields, local heat transfer, and global thermohydraulic performance. The inserts generated counter-rotating streamwise vortices, walldirected jets, separation and reattachment, and repeated thermal-boundary-layer renewal. The Nusselt-number ratio (Nu/Nu0) and Darcy friction factor ratio (f/f0) were 1.396–7.901 and 2.590–140.673, respectively. Although heat transfer increased with BR and decreasing PR, the pressure-loss penalty rose nonlinearly. The thermal enhancement factor (TEF) ranged from 0.531 to 2.327 and generally decreased with Re. The maximum TEF of 2.327 occurred at BR = 0.2, PR = 0.5, α = 30°, and Re = 3000, whereas the maximum Nu/Nu0 occurred at BR = 0.5 and α = 45°. Thus, moderate blockage and close spacing provide a better equal pumping power compromise than the most obstructive geometry.
- Open Access
Drying Kinetics, Apparent Moisture Diffusivity, and Energy Performance of Black Soldier Fly Larvae in a Rotating-Tray Hot-Air Dryer
Fresh black soldier fly larvae (BSFL) have a high moisture content that complicates storage and requires energy-intensive postharvest drying. This study evaluated the effects of drying-air temperature and tray rotation speed on BSFL drying kinetics, energy performance, and moisture transport in a rotating-tray hot-air dryer. A 3 × 3 factorial experiment was conducted at 50, 60, and 70 °C and tray rotation speeds of 0, 5, and 10 rpm, with three independent replicates, while drying-air velocity was maintained at 3.0 m s−1. Drying time decreased from 31.0 h at 50 °C and 0 rpm to 6.5 h at 70 °C and 10 rpm. The latter condition achieved the highest drying efficiency (49.11%) and lowest specific energy consumption (4.60 MJ kg−1 water removed). Comparable values were obtained at 60 °C and 10 rpm (49.07% and 4.61 MJ kg−1 water removed, respectively). Among nine thin-layer models evaluated for the six rotating-tray treatments at 5 and 10 rpm, the Midilli model provided the best fit. Apparent effective moisture diffusivity ( increased from 0.2457 × 10−9 to 1.2946 × 10−9 m2 s−1, while apparent activation energy ranged from 67.39 to 68.46 kJ mol−1. Rotating-tray drying accelerated BSFL dehydration and improved engineering performance; however, microbial safety and product quality require separate evaluation before food or feed recommendations can be made.Open AccessDrying Kinetics, Apparent Moisture Diffusivity, and Energy Performance of Black Soldier Fly Larvae in a Rotating-Tray Hot-Air Dryer
Fresh black soldier fly larvae (BSFL) have a high moisture content that complicates storage and requires energy-intensive postharvest drying. This study evaluated the effects of drying-air temperature and tray rotation speed on BSFL drying kinetics, energy performance, and moisture transport in a rotating-tray hot-air dryer. A 3 × 3 factorial experiment was conducted at 50, 60, and 70 °C and tray rotation speeds of 0, 5, and 10 rpm, with three independent replicates, while drying-air velocity was maintained at 3.0 m s−1. Drying time decreased from 31.0 h at 50 °C and 0 rpm to 6.5 h at 70 °C and 10 rpm. The latter condition achieved the highest drying efficiency (49.11%) and lowest specific energy consumption (4.60 MJ kg−1 water removed). Comparable values were obtained at 60 °C and 10 rpm (49.07% and 4.61 MJ kg−1 water removed, respectively). Among nine thin-layer models evaluated for the six rotating-tray treatments at 5 and 10 rpm, the Midilli model provided the best fit. Apparent effective moisture diffusivity ( increased from 0.2457 × 10−9 to 1.2946 × 10−9 m2 s−1, while apparent activation energy ranged from 67.39 to 68.46 kJ mol−1. Rotating-tray drying accelerated BSFL dehydration and improved engineering performance; however, microbial safety and product quality require separate evaluation before food or feed recommendations can be made. - Open Access
- 3 September 2026
- Published by Elsevier in SSRN Electronic Journal
Microbial lithium recovery from spent NMC batteries to synthesize tailored ZSM-5 catalysts for waste plastic depolymerization
The presented research describes a circular process combining recovery of lithium from lithium-ion batteries (LIBs) and synthesis of acidity tuned ZSM-5 catalysts used for catalytic pyrolysis of mixed plastic waste. The recovery of lithium from black mass of NMC111 LIB through a two step indirect bioleaching by Acidithiobacillus thiooxidans and Gluconobacter oxydans along with selective purification of lithium solution from transition metals is followed by the synthesis of Li doped ZSM-5 catalysts via ion-exchange procedure. Structure studies using XRD, NH₃-TPD, SEM-EDX and ICP-OES confirmed integrity of MFI structure, presence of incorporated lithium and stepwise decrease of the number of strong acid sites from 550 to 150 μmol g⁻¹ upon increase of Li concentration. Catalytic pyrolysis of feedstock composed of 10% LIB derived plastics and 90% LDPE/HDPE waste plastics was optimized using Box-Behnken Design with temperature (400-440 °C), catalyst loading (0-15 wt.%) and lithium content (0-3 wt.%) as independent factors. The ANOVA results indicated that all three variables and their interactions had significant effect on the yield of bio-oil, whereas the developed quadratic model showed excellent correlation with experimental results (R² = 0.9845). The numerical optimization gave maximum yield of bio-oil as 73.38% at temperature of 440 °C, catalyst concentration of 11.5 wt.% and lithium content of 2.85 wt.%. The validation test yielded 73.3% average yield of bio-oil. Under same reaction conditions, bio-recovered Li-ZSM-5 gave bio-oil yield of 71.5 wt.%, which was higher than Li-ZSM-5 (62.0 wt.%) and pure ZSM,K
- 3 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMicrobial lithium recovery from spent NMC batteries to synthesize tailored ZSM-5 catalysts for waste plastic depolymerization
The presented research describes a circular process combining recovery of lithium from lithium-ion batteries (LIBs) and synthesis of acidity tuned ZSM-5 catalysts used for catalytic pyrolysis of mixed plastic waste. The recovery of lithium from black mass of NMC111 LIB through a two step indirect bioleaching by Acidithiobacillus thiooxidans and Gluconobacter oxydans along with selective purification of lithium solution from transition metals is followed by the synthesis of Li doped ZSM-5 catalysts via ion-exchange procedure. Structure studies using XRD, NH₃-TPD, SEM-EDX and ICP-OES confirmed integrity of MFI structure, presence of incorporated lithium and stepwise decrease of the number of strong acid sites from 550 to 150 μmol g⁻¹ upon increase of Li concentration. Catalytic pyrolysis of feedstock composed of 10% LIB derived plastics and 90% LDPE/HDPE waste plastics was optimized using Box-Behnken Design with temperature (400-440 °C), catalyst loading (0-15 wt.%) and lithium content (0-3 wt.%) as independent factors. The ANOVA results indicated that all three variables and their interactions had significant effect on the yield of bio-oil, whereas the developed quadratic model showed excellent correlation with experimental results (R² = 0.9845). The numerical optimization gave maximum yield of bio-oil as 73.38% at temperature of 440 °C, catalyst concentration of 11.5 wt.% and lithium content of 2.85 wt.%. The validation test yielded 73.3% average yield of bio-oil. Under same reaction conditions, bio-recovered Li-ZSM-5 gave bio-oil yield of 71.5 wt.%, which was higher than Li-ZSM-5 (62.0 wt.%) and pure ZSM,K
- Open Access
- 27 August 2026
- Published by Elsevier in SSRN Electronic Journal
CO2-Assisted Catalytic Pyrolysis of Mixed Polyolefin Waste over Mesoporous Ga/ZSM-5: Integrating Response Surface Optimization with CFD-Based Transport Analysis
In this research work, CO2 assisted catalytic co-pyrolysis of a 50:50 blend of waste polyolefin plastic (PP/PE) and biomass (Napier grass) by employing mesoporous Ga/ZSM 5 catalyst and associated techniques, such as catalyst characterization, computational fluid dynamics simulations, and Box-Behnken optimization was studied. The findings obtained from X-ray diffraction showed that the MFI structure remained intact and crystalline Ga2O3 was not formed. From the results obtained via scanning electron microscope and energy dispersive spectroscopy, it was concluded that gallium was uniformly dispersed and hexagonal shape of the catalyst did not change. According to NH3 temperature programmed desorption, the acidity of the catalyst changed. Strong Brønsted sites decreased from 0.361 to 0.201 mmol g−1 and medium strength Lewis sites increased to 0.225 mmol g−1, whereas total acidity stayed almost constant (0.662–0.692 mmol g−1). The catalytic process allowed for increasing the transfer of heat, leading to 25–125 °C increase in reactor temperatures, and radial temperature gradients dropped from about 600 °C to 350-450 °C. As CO2 concentration (0–30 vol.%) increases, the particle Reynolds number drops from 9.87 to 7.61, indicating a transition towards diffusion-controlled transport. The application of response surface methodology shows that bio oil yields range from 44.7 to 65.7 wt.%, with the highest yield of 65.7 wt.% being achieved at 503.1 °C, 1.95 wt.% Ga loading over ZSM-5 and 22.5 vol.% CO2 (R2 = 0.986). The validation experiments confirm an average yield of 65.68 ± 0.38%.
- 27 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCO2-Assisted Catalytic Pyrolysis of Mixed Polyolefin Waste over Mesoporous Ga/ZSM-5: Integrating Response Surface Optimization with CFD-Based Transport Analysis
In this research work, CO2 assisted catalytic co-pyrolysis of a 50:50 blend of waste polyolefin plastic (PP/PE) and biomass (Napier grass) by employing mesoporous Ga/ZSM 5 catalyst and associated techniques, such as catalyst characterization, computational fluid dynamics simulations, and Box-Behnken optimization was studied. The findings obtained from X-ray diffraction showed that the MFI structure remained intact and crystalline Ga2O3 was not formed. From the results obtained via scanning electron microscope and energy dispersive spectroscopy, it was concluded that gallium was uniformly dispersed and hexagonal shape of the catalyst did not change. According to NH3 temperature programmed desorption, the acidity of the catalyst changed. Strong Brønsted sites decreased from 0.361 to 0.201 mmol g−1 and medium strength Lewis sites increased to 0.225 mmol g−1, whereas total acidity stayed almost constant (0.662–0.692 mmol g−1). The catalytic process allowed for increasing the transfer of heat, leading to 25–125 °C increase in reactor temperatures, and radial temperature gradients dropped from about 600 °C to 350-450 °C. As CO2 concentration (0–30 vol.%) increases, the particle Reynolds number drops from 9.87 to 7.61, indicating a transition towards diffusion-controlled transport. The application of response surface methodology shows that bio oil yields range from 44.7 to 65.7 wt.%, with the highest yield of 65.7 wt.% being achieved at 503.1 °C, 1.95 wt.% Ga loading over ZSM-5 and 22.5 vol.% CO2 (R2 = 0.986). The validation experiments confirm an average yield of 65.68 ± 0.38%.
- Open Access
- 18 July 2026
- Published by Elsevier in SSRN Electronic Journal
Multiphysics Optimization of an Induction-Heated Catalytic Auger Reactor for Plastic-Rubber Waste Pyrolysis via Coupled Maxwell-CFD Modeling
Thermochemical conversion of plastic and rubber waste is limited by poor thermal conductivity of polymeric materials (0.1 – 0.2 W/m·K) and, as a consequence, internal thermal gradients and over-cracking. This study introduces a 3D Maxwell-Multiphase Computational Fluid Dynamics model that integrates electromagnetic skin-depth attenuation and non-Newtonian multiphase hydrodynamics. The mathematical model is comprehensively verified on an experimentally developed prototype reactor based on a continuous induction-heated auger screw reactor equipped with segmented electromagnetic coils and an automated system of Fe-biochar catalyst co-feeding for selective vapor upgrade. Both modeling and experimental studies were performed systematically for varying screw flight pitch-to-diameter ratios (P/D), rotational speed and induction frequency. It was found that P/D compression up to 0.5 optimizes thermal homogeneity up to 0.94 but traps volatile products in the reactor, thus increasing the over-cracking ratio up to 0.38. At the same time, increasing P/D to 1.5 too much accelerates the transport and decreases the thermal homogeneity up to 0.62 with over-cracking reaching 0.45. A combination of an optimum P/D of 1.0 with an intermediate rotational speed of 30-40 RPM creates perfect conditions for hydrodynamic stability, providing the minimum over-cracking ratio of 0.18, maximum production of liquid bio-oil up to 55.0% and minimal amount of artificial gas up to 10.0%. In addition, an electromagnetic study demonstrated the presence of very high frequencies of heating (250-300 kHz) causing super-heating of the peripheral zones of material more than 650 ºC and reducing thermal homogeneity to 0.60 due to dominance of electromagnetic energy over mechanical stirring.
- 18 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMultiphysics Optimization of an Induction-Heated Catalytic Auger Reactor for Plastic-Rubber Waste Pyrolysis via Coupled Maxwell-CFD Modeling
Thermochemical conversion of plastic and rubber waste is limited by poor thermal conductivity of polymeric materials (0.1 – 0.2 W/m·K) and, as a consequence, internal thermal gradients and over-cracking. This study introduces a 3D Maxwell-Multiphase Computational Fluid Dynamics model that integrates electromagnetic skin-depth attenuation and non-Newtonian multiphase hydrodynamics. The mathematical model is comprehensively verified on an experimentally developed prototype reactor based on a continuous induction-heated auger screw reactor equipped with segmented electromagnetic coils and an automated system of Fe-biochar catalyst co-feeding for selective vapor upgrade. Both modeling and experimental studies were performed systematically for varying screw flight pitch-to-diameter ratios (P/D), rotational speed and induction frequency. It was found that P/D compression up to 0.5 optimizes thermal homogeneity up to 0.94 but traps volatile products in the reactor, thus increasing the over-cracking ratio up to 0.38. At the same time, increasing P/D to 1.5 too much accelerates the transport and decreases the thermal homogeneity up to 0.62 with over-cracking reaching 0.45. A combination of an optimum P/D of 1.0 with an intermediate rotational speed of 30-40 RPM creates perfect conditions for hydrodynamic stability, providing the minimum over-cracking ratio of 0.18, maximum production of liquid bio-oil up to 55.0% and minimal amount of artificial gas up to 10.0%. In addition, an electromagnetic study demonstrated the presence of very high frequencies of heating (250-300 kHz) causing super-heating of the peripheral zones of material more than 650 ºC and reducing thermal homogeneity to 0.60 due to dominance of electromagnetic energy over mechanical stirring.
- Open Access
- 1 July 2026
- Published by Elsevier in SSRN Electronic Journal
Bio‐Recovered Lithium‐Doped ZSM‐5 for Acidity‐Tuned Catalytic Pyrolysis of Waste Plastics: From Spent Lithium‐Ion Batteries to Catalysts
This research combines the sustainability of lithium recovery with tuned acidity catalysts for the production of high-yield bio-oil from mixed waste plastics while fostering a circular economy for resources. Lithium was extracted from spent NMC111 Lithium-Ion battery waste black masses via a hybrid bioleaching method using Acidithiobacillus thiooxidans and Gluconobacter oxydans. After impurities were removed and verified by ICP, the purified lithium solution was utilized for the synthesis of Li-Doped ZSM-5 catalysts via ion exchange. Catalyst characterization was performed using XRD, NH₃ TPD, and SEM-EDX to confirm structural integrity, moderate acidity, and homogeneous dopant distribution. A Box-Behnken Design (BBD) was utilized to create a mathematical model for optimizing the production of bio-oil from the catalytic pyrolysis of a mixture of waste plastics containing 10% LIB waste plastics and 90% LDPE/HDPE waste plastics, with temperature (400-440°C), catalyst amount (0-15 wt.%), and Li doped (0-3 wt.%) as variables. Numerical optimization predicted an optimal combination of 440 °C, 11.5 wt.% catalyst amount, and 2.85 wt.% Li to achieve a maximum predicted yield of 73.38%. Validation after 6 experimental trials at optimized parameter confirmed an experimental mean yield of 73.3%, within the 95% confidence interval.
- 1 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessBio‐Recovered Lithium‐Doped ZSM‐5 for Acidity‐Tuned Catalytic Pyrolysis of Waste Plastics: From Spent Lithium‐Ion Batteries to Catalysts
This research combines the sustainability of lithium recovery with tuned acidity catalysts for the production of high-yield bio-oil from mixed waste plastics while fostering a circular economy for resources. Lithium was extracted from spent NMC111 Lithium-Ion battery waste black masses via a hybrid bioleaching method using Acidithiobacillus thiooxidans and Gluconobacter oxydans. After impurities were removed and verified by ICP, the purified lithium solution was utilized for the synthesis of Li-Doped ZSM-5 catalysts via ion exchange. Catalyst characterization was performed using XRD, NH₃ TPD, and SEM-EDX to confirm structural integrity, moderate acidity, and homogeneous dopant distribution. A Box-Behnken Design (BBD) was utilized to create a mathematical model for optimizing the production of bio-oil from the catalytic pyrolysis of a mixture of waste plastics containing 10% LIB waste plastics and 90% LDPE/HDPE waste plastics, with temperature (400-440°C), catalyst amount (0-15 wt.%), and Li doped (0-3 wt.%) as variables. Numerical optimization predicted an optimal combination of 440 °C, 11.5 wt.% catalyst amount, and 2.85 wt.% Li to achieve a maximum predicted yield of 73.38%. Validation after 6 experimental trials at optimized parameter confirmed an experimental mean yield of 73.3%, within the 95% confidence interval.
- Open Access
- 29 May 2026
- Published by Elsevier in SSRN Electronic Journal
Thermal–Catalytic Coupling in Plastic Waste Pyrolysis: A CFD-Driven Study of Heat Transfer Enhancement Using Ca–Fe Modified Biochar
Pyrolysis of plastic wastes and rubber is considered a promising method for production of bio-oil. This research introduces a CFD model, verified via experimental studies, for the analysis of heat transfer and reaction process in a lab-scale batch reactor employing Ca-Fe biochar-modified catalyst. This material shows enhanced physical and chemical characteristics, which include an increased specific surface area of 245.8 m2g−1, pore volume of 0.38 cm3g−1, and a bimodal distribution with peaks at 9.2 and 25.5 nm. NH3-TPD results in the high value of acidity, equal to 1.30 mmol g−1 (0.51, 0.45, and 0.34 for weak, medium, and strong acids correspondingly), which far exceeds that of unmodified biochar (0.40 mmol g−1). The CFD model couples transient heat conduction with Arrhenius kinetics and catalyst-dependent thermophysical properties. Predictions made by the model are in good agreement with experimental results with temperature deviations of less than 6% and deviations of conversion of less than 8%. In addition, it makes use of the catalytic system which facilitates efficient heat conductivity (up to 2.0 W m−1 K−1) and minimizes radial temperature differences, hence heat is transferred into the system at a faster rate with an earlier achievement of heat balance. Hence, the amount of bio-oil produced increases to 48.3 wt.% while the amount of char formed is reduced to 17.7 wt.%.
- 29 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessThermal–Catalytic Coupling in Plastic Waste Pyrolysis: A CFD-Driven Study of Heat Transfer Enhancement Using Ca–Fe Modified Biochar
Pyrolysis of plastic wastes and rubber is considered a promising method for production of bio-oil. This research introduces a CFD model, verified via experimental studies, for the analysis of heat transfer and reaction process in a lab-scale batch reactor employing Ca-Fe biochar-modified catalyst. This material shows enhanced physical and chemical characteristics, which include an increased specific surface area of 245.8 m2g−1, pore volume of 0.38 cm3g−1, and a bimodal distribution with peaks at 9.2 and 25.5 nm. NH3-TPD results in the high value of acidity, equal to 1.30 mmol g−1 (0.51, 0.45, and 0.34 for weak, medium, and strong acids correspondingly), which far exceeds that of unmodified biochar (0.40 mmol g−1). The CFD model couples transient heat conduction with Arrhenius kinetics and catalyst-dependent thermophysical properties. Predictions made by the model are in good agreement with experimental results with temperature deviations of less than 6% and deviations of conversion of less than 8%. In addition, it makes use of the catalytic system which facilitates efficient heat conductivity (up to 2.0 W m−1 K−1) and minimizes radial temperature differences, hence heat is transferred into the system at a faster rate with an earlier achievement of heat balance. Hence, the amount of bio-oil produced increases to 48.3 wt.% while the amount of char formed is reduced to 17.7 wt.%.