Ibrohim Khasanov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ibrohim Khasanov has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Asroriddin Kasimov
Department of Physics, Faculty of Physics and Mathematics, Termez State University, 43, Barkamol Avlod Str., Termez 190111, Uzbekistan
1 shared publication - Dilsabo Choriyeva
Department of Agricultural Engineering, Karshi State Technical University, Karshi 180100, Uzbekistan
1 shared publication - Farmon Mamatov
Department of Agricultural Engineering, Karshi State Technical University, Karshi 180100, Uzbekistan
1 shared publication - Makhmatmurod Shomirzaev
Department of Technological Education, Termez State University, Termez 190111, Uzbekistan
1 shared publication - Muhriddin Buriev
Department of Agricultural Engineering, Karshi State Technical University, Karshi 180100, Uzbekistan
1 shared publication - Muxtor Khalilov
Department of Agricultural Engineering, Karshi State Technical University, Karshi 180100, Uzbekistan
1 shared publication
Latest Publications
- Open Access
- 7 June 2026
- Published by MDPI AG in Agriculture
- Vol. 16 (12) , 1260
Soil Fragmentation, Surface Roughness and Draft Force in Chisel Tillage with a Toothed Roller: Experimental and Analytical Study
Efficient seedbed preparation under conservation-oriented tillage requires balanced aggregate fragmentation, surface microrelief and energy demand. This study investigated the influence of passive toothed roller parameters on soil fragmentation, surface roughness, draft force and fuel consumption during chisel tillage under medium-loam Calcisol conditions. Three configurations were compared: a chisel plow without a roller, with a slat roller and with a toothed roller. An analytical framework describing aggregate capture, tooth–soil contact frequency and resistance formation was combined with field experiments and regression-based response surface analysis. The toothed roller improved measured soil treatment indicators compared with the no-roller and slat-roller configurations due to discrete tooth–soil interaction, localized stress concentration and repeated loading of loosened aggregates. Rational parameter ranges were identified: a roller diameter of 0.45–0.46 m, 13–15 teeth, transverse spacing of 8.0–8.6 cm, a tooth height of 7.5–8.5 cm and specific load of 0.9–1.1 kN m−1. Under the selected configuration, aggregates smaller than 50 mm increased from 76.1% to 88.0%, surface roughness decreased from 6.8 to 3.7 cm and residue retention remained above 60%. Fuel consumption increased to 28.4–28.5 L ha−1, reflecting the additional energetic cost of fragmentation and levelling. The approach supports rational selection of passive toothed roller parameters under the tested conditions.
- 7 June 2026
- Published by MDPI AG in Agriculture
- Vol. 16 (12) , 1260
Open AccessSoil Fragmentation, Surface Roughness and Draft Force in Chisel Tillage with a Toothed Roller: Experimental and Analytical Study
Efficient seedbed preparation under conservation-oriented tillage requires balanced aggregate fragmentation, surface microrelief and energy demand. This study investigated the influence of passive toothed roller parameters on soil fragmentation, surface roughness, draft force and fuel consumption during chisel tillage under medium-loam Calcisol conditions. Three configurations were compared: a chisel plow without a roller, with a slat roller and with a toothed roller. An analytical framework describing aggregate capture, tooth–soil contact frequency and resistance formation was combined with field experiments and regression-based response surface analysis. The toothed roller improved measured soil treatment indicators compared with the no-roller and slat-roller configurations due to discrete tooth–soil interaction, localized stress concentration and repeated loading of loosened aggregates. Rational parameter ranges were identified: a roller diameter of 0.45–0.46 m, 13–15 teeth, transverse spacing of 8.0–8.6 cm, a tooth height of 7.5–8.5 cm and specific load of 0.9–1.1 kN m−1. Under the selected configuration, aggregates smaller than 50 mm increased from 76.1% to 88.0%, surface roughness decreased from 6.8 to 3.7 cm and residue retention remained above 60%. Fuel consumption increased to 28.4–28.5 L ha−1, reflecting the additional energetic cost of fragmentation and levelling. The approach supports rational selection of passive toothed roller parameters under the tested conditions.