Md. Kawsarul Islam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Md. Kawsarul Islam has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Md. Mamun
Graduate School of Engineering, Osaka Sangyo University, Osaka 574-8530, Japan
2 shared publications - Md. Mesbah Uddin Saadi
Department of Mechanical Engineering, Dhaka University of Engineering & Technology, Gazipur 1707, Bangladesh
2 shared publications - Miah Md Ashraful Alam
Department of Systems Engineering, Osaka Sangyo University, Osaka 574-8530, Japan
2 shared publications - Manabu Takao
National Institute of Technology, Matsue College
1 shared publication - Takayuki Kuri
Graduate School of Engineering, Osaka Sangyo University, Osaka 574-8530, Japan
1 shared publication - Yoshiaki Hatsuse
Graduate School of Engineering, Osaka Sangyo University, Osaka 574-8530, Japan
1 shared publication
Latest Publications
- Open Access
Rarefied Intake Flow in an Atmospheric-Breathing VLEO Hall Thruster
Atmosphere-breathing Hall thrusters (ABHTs) have emerged as a promising propulsion technology for very low Earth orbit (VLEO) satellites because they can utilize residual atmospheric particles as propellant, reducing the need for onboard propellant storage. In this paper, the feasibility of an ABHT system was investigated through a combined experimental and numerical approach. Experimental tests using the THT-VI Hall thruster demonstrated stable operation with air propellant and achieved specific impulses up to 2847 s under high-voltage conditions, indicating the potential for atmospheric drag compensation. To evaluate the intake performance, Direct Simulation Monte Carlo (DSMC) simulations were conducted at an altitude of 180 km to examine the effects of intake geometry, including the duct aspect ratio and intake-to-thruster area ratio. The results showed that the intake system can generate discharge chamber pressures of approximately 10−3–10−1 Pa, which is sufficient for Hall thruster operation, but the maximum collected mass flow rate (0.298 mg/s) remained below the required 1.5 mg/s. Several modified intake configurations improved particle transport and reduced aerodynamic drag with the best design increasing mass flow rate by approximately 7.5 times compared with the baseline configuration. These findings indicate that the primary limitation of ABHT systems is the intake mass transport capability rather than the thruster performance itself. A further optimization of intake geometry and spacecraft integration is required to enable sustained VLEO operation.
Open AccessRarefied Intake Flow in an Atmospheric-Breathing VLEO Hall Thruster
Atmosphere-breathing Hall thrusters (ABHTs) have emerged as a promising propulsion technology for very low Earth orbit (VLEO) satellites because they can utilize residual atmospheric particles as propellant, reducing the need for onboard propellant storage. In this paper, the feasibility of an ABHT system was investigated through a combined experimental and numerical approach. Experimental tests using the THT-VI Hall thruster demonstrated stable operation with air propellant and achieved specific impulses up to 2847 s under high-voltage conditions, indicating the potential for atmospheric drag compensation. To evaluate the intake performance, Direct Simulation Monte Carlo (DSMC) simulations were conducted at an altitude of 180 km to examine the effects of intake geometry, including the duct aspect ratio and intake-to-thruster area ratio. The results showed that the intake system can generate discharge chamber pressures of approximately 10−3–10−1 Pa, which is sufficient for Hall thruster operation, but the maximum collected mass flow rate (0.298 mg/s) remained below the required 1.5 mg/s. Several modified intake configurations improved particle transport and reduced aerodynamic drag with the best design increasing mass flow rate by approximately 7.5 times compared with the baseline configuration. These findings indicate that the primary limitation of ABHT systems is the intake mass transport capability rather than the thruster performance itself. A further optimization of intake geometry and spacecraft integration is required to enable sustained VLEO operation.
- Open Access
- 18 June 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (12) , 6190
Mixing Characteristics of Supersonic Jets Injected into a Pressurized Gas Environment
The transition toward carbon-neutral energy systems has accelerated interest in hydrogen-fueled combustion technologies, where efficient fuel–air mixing is essential for stable and clean combustion. In the present study, the mixing characteristics of under-expanded supersonic jets injected into a pressurized environment are numerically investigated using validated computational fluid dynamics simulations. Two nozzle configurations are examined: a straight nozzle and sudden-expansion nozzles with different expansion ratios and expansion locations. The governing compressible flow equations are solved using the rhoCentralFoam solver with the SST k–ω turbulence model. The numerical framework is validated against Sod’s shock tube solution and experimental data for under-expanded supersonic free jets. The results show that sudden-expansion nozzles significantly modify the shock-wave structure, jet penetration, and lateral spreading compared with the straight nozzle. Among the investigated configurations, nozzles with intermediate expansion-section lengths exhibited pronounced Mach-disk oscillations with a dominant frequency of approximately 10 kHz. The normalized supersonic core length decreased from 17.79 for the straight nozzle to 5.50 for the best-performing sudden-expansion configuration, while the normalized jet half-width increased from 0.82 to 1.70, indicating substantially enhanced mixing performance. The findings demonstrate that nozzle geometry strongly governs the trade-off between flow stability and mixing enhancement in high-pressure supersonic jets.
- 18 June 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (12) , 6190
Open AccessMixing Characteristics of Supersonic Jets Injected into a Pressurized Gas Environment
The transition toward carbon-neutral energy systems has accelerated interest in hydrogen-fueled combustion technologies, where efficient fuel–air mixing is essential for stable and clean combustion. In the present study, the mixing characteristics of under-expanded supersonic jets injected into a pressurized environment are numerically investigated using validated computational fluid dynamics simulations. Two nozzle configurations are examined: a straight nozzle and sudden-expansion nozzles with different expansion ratios and expansion locations. The governing compressible flow equations are solved using the rhoCentralFoam solver with the SST k–ω turbulence model. The numerical framework is validated against Sod’s shock tube solution and experimental data for under-expanded supersonic free jets. The results show that sudden-expansion nozzles significantly modify the shock-wave structure, jet penetration, and lateral spreading compared with the straight nozzle. Among the investigated configurations, nozzles with intermediate expansion-section lengths exhibited pronounced Mach-disk oscillations with a dominant frequency of approximately 10 kHz. The normalized supersonic core length decreased from 17.79 for the straight nozzle to 5.50 for the best-performing sudden-expansion configuration, while the normalized jet half-width increased from 0.82 to 1.70, indicating substantially enhanced mixing performance. The findings demonstrate that nozzle geometry strongly governs the trade-off between flow stability and mixing enhancement in high-pressure supersonic jets.