Andrea Picco
Andrea Picco has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Amalia Balsamo
STMicroelectronics
2 shared publications - Andrea Serafini
Politecnico di Milano, Department of Chemistry, Materials and Chemical Engineering “G. Natta”, 20131 Milano, Italy
2 shared publications - Anirban Ghosh
Silicon Austria Labs GmbH
2 shared publications - Annalisa De Pastina
Silicon Austria Labs GmbH
2 shared publications - Davide Codegoni
STMicroelectronics
2 shared publications - Demian Henzen
Evatec AG
2 shared publications
Latest Publications
- Open Access
- 17 November 2026
- Published by Wiley in Small Science
- Vol. 6 (11)
From Bulk Ceramics to Phase Engineering of K (1− x ) Na x NbO 3 Thin Films
Since the initial discovery of the extraordinary piezoelectric coefficients of potassium sodium niobate (KNN) in near‐equimolar bulk ceramics, its development has proceeded unevenly, with its integration into microelectronics severely lagging due to thermodynamic stability issues and poor planar process compatibility. In this work, we revisit the bulk‐derived phase diagram for the specific case of thin films integrated on silicon. By systematically investigating Mn‐doped K 1− x Na x NbO 3 films, grown by confocal sputtering on 8‐inch wafers, with 0.42 < x < 0.83, we demonstrate that the optimal stoichiometry for thin films fundamentally diverges from the bulk equimolar standard. Na‐rich compositions ( x > 0.7) reduce alkali deficiency, macroscopic segregation, and pyrochlore formation while promoting dense columnar growth with strong {001} fiber texture, although local chemical heterogeneity persists. These films exhibit remanent polarizations up to ~14 µC cm −2 , with d 33,f ≈ 79 pm V −1 and e 31,f ≈ 10 C m −2 . Thanks to density functional theory calculations, we associate the enhanced response with increased structural stability and a possible strain‐driven reorientation toward lower‐symmetry monoclinic or orthorhombic configurations with tilted polarization. These results redefine phase‐engineering rules for wafer‐scale KNN thin films and provide a route toward their integration in microsystems.
- 17 November 2026
- Published by Wiley in Small Science
- Vol. 6 (11)
Open AccessFrom Bulk Ceramics to Phase Engineering of K (1− x ) Na x NbO 3 Thin Films
Since the initial discovery of the extraordinary piezoelectric coefficients of potassium sodium niobate (KNN) in near‐equimolar bulk ceramics, its development has proceeded unevenly, with its integration into microelectronics severely lagging due to thermodynamic stability issues and poor planar process compatibility. In this work, we revisit the bulk‐derived phase diagram for the specific case of thin films integrated on silicon. By systematically investigating Mn‐doped K 1− x Na x NbO 3 films, grown by confocal sputtering on 8‐inch wafers, with 0.42 < x < 0.83, we demonstrate that the optimal stoichiometry for thin films fundamentally diverges from the bulk equimolar standard. Na‐rich compositions ( x > 0.7) reduce alkali deficiency, macroscopic segregation, and pyrochlore formation while promoting dense columnar growth with strong {001} fiber texture, although local chemical heterogeneity persists. These films exhibit remanent polarizations up to ~14 µC cm −2 , with d 33,f ≈ 79 pm V −1 and e 31,f ≈ 10 C m −2 . Thanks to density functional theory calculations, we associate the enhanced response with increased structural stability and a possible strain‐driven reorientation toward lower‐symmetry monoclinic or orthorhombic configurations with tilted polarization. These results redefine phase‐engineering rules for wafer‐scale KNN thin films and provide a route toward their integration in microsystems.
- 5 August 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (31) , 315102
Wafer-scale integration of piezo- and ferroelectric Al 0.64 Sc 0.36 N thin films by reactive sputtering
Large-area deposition of aluminum-scandium-nitride (Al 1 −x Sc x N) thin films with higher Sc content ( x ) remains challenging due to several issues, such as abnormal orientation growth, stress control, and the undesired crystal phase. These anomalies across the wafer hinder the development of high scandium-content AlScN films, which are critical for microelectromechanical systems (MEMS) applications. In this study, we report on the sputter deposition of Al 0.64 Sc 0.36 N thin films from a 304 mm diameter Al 0.64 Sc 0.36 alloy target on 200 mm Si (100) wafers, achieving an exceptionally high deposition rate of 8.7 μ m h −1 with less than 1% abnormally oriented grains and controllable stress tuning. Comprehensive microstructural and electrical characterizations confirm the superior growth of high-quality Al 0.64 Sc 0.36 N films with exceptional wafer-averaged piezoelectric coefficients ( d 33 ,f = 15.62 pm V −1 and e 31 ,f = −2.9 C m −2 ) due to low point defects density and grain mosaicity. This is accomplished through the implementation of an optimized seed layer and a refined electrode integration strategy, along with optimal process conditions. The wafer yield and device failure rates are analyzed and correlated with the average stress of the films and their stress profiles along the diameter. The resulting films demonstrate excellent uniformity in structural, compositional, and piezoelectric properties across the entire 200 mm wafer, underscoring their strong potential for next-generation MEMS applications.
- 5 August 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (31) , 315102
Wafer-scale integration of piezo- and ferroelectric Al 0.64 Sc 0.36 N thin films by reactive sputtering
Large-area deposition of aluminum-scandium-nitride (Al 1 −x Sc x N) thin films with higher Sc content ( x ) remains challenging due to several issues, such as abnormal orientation growth, stress control, and the undesired crystal phase. These anomalies across the wafer hinder the development of high scandium-content AlScN films, which are critical for microelectromechanical systems (MEMS) applications. In this study, we report on the sputter deposition of Al 0.64 Sc 0.36 N thin films from a 304 mm diameter Al 0.64 Sc 0.36 alloy target on 200 mm Si (100) wafers, achieving an exceptionally high deposition rate of 8.7 μ m h −1 with less than 1% abnormally oriented grains and controllable stress tuning. Comprehensive microstructural and electrical characterizations confirm the superior growth of high-quality Al 0.64 Sc 0.36 N films with exceptional wafer-averaged piezoelectric coefficients ( d 33 ,f = 15.62 pm V −1 and e 31 ,f = −2.9 C m −2 ) due to low point defects density and grain mosaicity. This is accomplished through the implementation of an optimized seed layer and a refined electrode integration strategy, along with optimal process conditions. The wafer yield and device failure rates are analyzed and correlated with the average stress of the films and their stress profiles along the diameter. The resulting films demonstrate excellent uniformity in structural, compositional, and piezoelectric properties across the entire 200 mm wafer, underscoring their strong potential for next-generation MEMS applications.
- 15 June 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (23)
200 mm wafer-scale integration of bilayer wurtzite ferroelectric AlScN exhibiting effective d33,f > 26.8 pm/V and e31,f > 4.6 C/m2
We report the successful integration of a bilayer ferroelectric aluminum–scandium–nitride (Al0.64Sc0.36N) thin film on an industrial-scale 200 mm silicon (100) wafer. Microstructural analysis revealed that both the bottom and top Al0.64Sc0.36N layers exhibit comparable characteristics. Wafer-scale ferroelectric and piezoelectric characterization of the individual layers showed similar average values for permittivity (ɛ), loss tangent (tan δ), and piezoelectric coefficients (d33,f and e31,f). Findings suggest that the bottom Al0.64Sc0.36N layer has a lower leakage current than the top layer in the bilayer configuration. We present a strategy for efficiently actuating both the top and bottom layers to generate a high equivalent longitudinal strain and transverse stress without requiring any complex or additional electrical circuitry. Upon excitation, the bilayer structure yields equivalent d33,f and e31,f values of >26.8 pm/V and >4.6 C/m2, respectively, among the highest ever reported within bilayers of complementary metal–oxide–semiconductor (CMOS) compatible ferroelectric nitride thin films. Such high piezoelectric coefficients enable the broader adoption of lead-free ferroelectric materials for actuator applications.
- 15 June 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (23)
200 mm wafer-scale integration of bilayer wurtzite ferroelectric AlScN exhibiting effective d33,f > 26.8 pm/V and e31,f > 4.6 C/m2
We report the successful integration of a bilayer ferroelectric aluminum–scandium–nitride (Al0.64Sc0.36N) thin film on an industrial-scale 200 mm silicon (100) wafer. Microstructural analysis revealed that both the bottom and top Al0.64Sc0.36N layers exhibit comparable characteristics. Wafer-scale ferroelectric and piezoelectric characterization of the individual layers showed similar average values for permittivity (ɛ), loss tangent (tan δ), and piezoelectric coefficients (d33,f and e31,f). Findings suggest that the bottom Al0.64Sc0.36N layer has a lower leakage current than the top layer in the bilayer configuration. We present a strategy for efficiently actuating both the top and bottom layers to generate a high equivalent longitudinal strain and transverse stress without requiring any complex or additional electrical circuitry. Upon excitation, the bilayer structure yields equivalent d33,f and e31,f values of >26.8 pm/V and >4.6 C/m2, respectively, among the highest ever reported within bilayers of complementary metal–oxide–semiconductor (CMOS) compatible ferroelectric nitride thin films. Such high piezoelectric coefficients enable the broader adoption of lead-free ferroelectric materials for actuator applications.