Vaishnavee Selvarajoo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Vaishnavee Selvarajoo has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Nahal Ghanadi
School of Mechanical, Industrial and Manufacturing Engineering, Oregon State University, Corvallis, OR 97331, USA
2 shared publications - Somayeh Pasebani
School of Mechanical, Industrial and Manufacturing Engineering, Oregon State University, Corvallis, OR 97331, USA
2 shared publications
Latest Publications
- Open Access
Understanding the Mixing in the Inconel–GRCop-42 Interface Fabricated by Laser Powder Bed Fusion
Laser powder bed fusion (LPBF) enables fabrication of complex bimetallic structures, such as combustion chambers, that require a thermally conductive internal liner supported by a high-strength structural jacket. Inconel 625 (IN625) served as the substrate, with GRCop-42, a Cu-Cr-Nb alloy developed by NASA Glenn Research Center, deposited with varying laser powers and laser scanning speeds to create the IN625–GRCop-42 interface. Hot isostatic pressing (HIP) was performed to evaluate defect mitigation, and Vickers microhardness testing was conducted to assess the mechanical properties across the bimetallic interface. Microstructure characterization revealed porosity across the full processing window and, along with density measurements, we were able to establish that the HIP treatment was unsuccessful in eliminating the defects, indicating that densification is primarily achieved by LPBF process optimization. Microhardness testing showed that the as-printed samples showed higher microhardness values than the as-HIPped samples due to the fine microstructure, high dislocation density and residual stresses caused by the LPBF process. The decrease in microhardness following HIP suggests that recrystallization, grain coarsening and residual stress relief may have occurred during post-processing. These results highlight the importance of LPBF process optimization in achieving strong, thermally stable IN625–GRCop-42 bimetallic interfaces. This study investigates the microstructural and mechanical behavior of the IN625 and GRCop-42 dissimilar metal interfaces fabricated using the LPBF process and the effects of HIP on the bimetallic microstructure.
Open AccessUnderstanding the Mixing in the Inconel–GRCop-42 Interface Fabricated by Laser Powder Bed Fusion
Laser powder bed fusion (LPBF) enables fabrication of complex bimetallic structures, such as combustion chambers, that require a thermally conductive internal liner supported by a high-strength structural jacket. Inconel 625 (IN625) served as the substrate, with GRCop-42, a Cu-Cr-Nb alloy developed by NASA Glenn Research Center, deposited with varying laser powers and laser scanning speeds to create the IN625–GRCop-42 interface. Hot isostatic pressing (HIP) was performed to evaluate defect mitigation, and Vickers microhardness testing was conducted to assess the mechanical properties across the bimetallic interface. Microstructure characterization revealed porosity across the full processing window and, along with density measurements, we were able to establish that the HIP treatment was unsuccessful in eliminating the defects, indicating that densification is primarily achieved by LPBF process optimization. Microhardness testing showed that the as-printed samples showed higher microhardness values than the as-HIPped samples due to the fine microstructure, high dislocation density and residual stresses caused by the LPBF process. The decrease in microhardness following HIP suggests that recrystallization, grain coarsening and residual stress relief may have occurred during post-processing. These results highlight the importance of LPBF process optimization in achieving strong, thermally stable IN625–GRCop-42 bimetallic interfaces. This study investigates the microstructural and mechanical behavior of the IN625 and GRCop-42 dissimilar metal interfaces fabricated using the LPBF process and the effects of HIP on the bimetallic microstructure.
- Open Access
- 2 July 2026
- Published by MDPI AG in Preprints.org
Understanding the Microstructure of Mixing in Inconel-GRCop-42 Interface Fabricated by Laser Powder Bed Fusion
Laser powder bed fusion (LPBF) enables fabrication of complex bimetallic structures, such as combustion chambers, that require a thermally conductive internal channel supported with a high-strength structural jacket. Inconel625 (IN625) served as the substrate, with GRCop-42 deposited with varying laser power and laser scanning speeds to create the IN625-GRCop-42 interface. Hot isostatic pressing (HIP) was performed to evaluate defect mitigation and Vickers microhardness testing assessed the mechanical properties across the bimetallic interface. Microstructure characterization revealed porosity across the full processing window and HIP was unsuccessful in eliminating the defects, indicating that densification is primarily achieved by LPBF process optimization. Microhardness testing proved that the as-printed samples showed higher microhardness values than the as-HIPped samples due to the fine microstructure, high dislocation density and residual stresses caused by the LPBF process. As-HIPped samples showed recrystallization and grain coarsening due to the decrease in microhardness compared to the as-printed samples. These results highlight the importance of LPBF process optimization in achieving strong, thermally stable IN625-GRCop-42 bimetallic interfaces. This study aims to investigate the microstructural and mechanical behavior of the IN625 and GRCop-42 dissimilar metal interface fabricated using the LPBF process and the effects of HIP on the bimetallic microstructure.
- 2 July 2026
- Published by MDPI AG in Preprints.org
Open AccessUnderstanding the Microstructure of Mixing in Inconel-GRCop-42 Interface Fabricated by Laser Powder Bed Fusion
Laser powder bed fusion (LPBF) enables fabrication of complex bimetallic structures, such as combustion chambers, that require a thermally conductive internal channel supported with a high-strength structural jacket. Inconel625 (IN625) served as the substrate, with GRCop-42 deposited with varying laser power and laser scanning speeds to create the IN625-GRCop-42 interface. Hot isostatic pressing (HIP) was performed to evaluate defect mitigation and Vickers microhardness testing assessed the mechanical properties across the bimetallic interface. Microstructure characterization revealed porosity across the full processing window and HIP was unsuccessful in eliminating the defects, indicating that densification is primarily achieved by LPBF process optimization. Microhardness testing proved that the as-printed samples showed higher microhardness values than the as-HIPped samples due to the fine microstructure, high dislocation density and residual stresses caused by the LPBF process. As-HIPped samples showed recrystallization and grain coarsening due to the decrease in microhardness compared to the as-printed samples. These results highlight the importance of LPBF process optimization in achieving strong, thermally stable IN625-GRCop-42 bimetallic interfaces. This study aims to investigate the microstructural and mechanical behavior of the IN625 and GRCop-42 dissimilar metal interface fabricated using the LPBF process and the effects of HIP on the bimetallic microstructure.