Luan Júlio Ruiz da Silva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Luan Júlio Ruiz da Silva has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Cristiane de Melo Alencar
School of Dentistry, University Center of State of Pará (CESUPA), Belém, Brazil
2 shared publications - Antonia Patricia Oliveira Barros
São Paulo State University, Brazil
1 shared publication - Diana Moreira Gomes Martins
School of Dentistry, University Center of the State of Pará - CESUPA, Belém, Brazil
1 shared publication - Larissa Fiorin Arruda
School of Dentistry, University Center of the State of Pará - CESUPA, Belém, Brazil
1 shared publication - Max Pinto da Costa da Rocha
School of Dentistry, Federal University of Pará - UFPA, Belém, Brazil
1 shared publication - Mileide da Paz Brito
School of Dentistry University Center of the State of Pará Belém Pará Brazil
1 shared publication
Latest Publications
- Open Access
- 27 August 2026
- Published by Springer Nature in Odontology
- p. 1-10
Bond strength performance of a self-curing bulk-fill restorative system and light-cured restorative systems after aging: an in vitro study
The microtensile bond strength (µTBS) and failure patterns of a self-curing bulk-fill restorative system (STELA, SDI) were investigated and compared with those of a light-cured bulk-fill and a conventional light-cured restorative system following short- and long-term aging in artificial saliva. Forty-eight human teeth were randomly assigned to three groups ( n = 16): G1, self-curing bulk-fill restorative system; G2, light-cured bulk-fill restorative system; and G3, conventional light-cured restorative system applied incrementally. Intact restored teeth were stored in artificial saliva for either 24 h or 18 months ( n = 8 per condition) and were sectioned only after completion of the respective aging period to obtain five beam-shaped specimens (≈ 0.9 mm²). The tooth was considered the experimental unit. Specimens were stored for either 24 h or 18 months ( n = 8 per condition). µTBS was assessed at a crosshead speed of 1 mm/min, and failure modes were determined using stereomicroscopy, with representative samples analyzed by scanning electron microscopy. Data were subjected to two-way ANOVA and Tukey’s post hoc test (α = 0.05). Bond strength was significantly influenced by both restorative system and aging time ( p < 0.001). A significant interaction between restorative system and aging condition was also detected ( p < 0.001). G2 exhibited the lowest µTBS values and a higher prevalence of adhesive failures. In contrast, G1 showed bond strength comparable to G3 and significantly higher than G2. Cohesive failures predominated in G1 and G3, whereas adhesive failures were more frequent in G2. Within the limitations of this in vitro study, the self-curing bulk-fill restorative system demonstrated adhesive performance similar to the conventional restorative system and preserved its relative behavior after aging, under the respective adhesive strategies recommended by the manufacturers.
- 27 August 2026
- Published by Springer Nature in Odontology
- p. 1-10
Open AccessBond strength performance of a self-curing bulk-fill restorative system and light-cured restorative systems after aging: an in vitro study
The microtensile bond strength (µTBS) and failure patterns of a self-curing bulk-fill restorative system (STELA, SDI) were investigated and compared with those of a light-cured bulk-fill and a conventional light-cured restorative system following short- and long-term aging in artificial saliva. Forty-eight human teeth were randomly assigned to three groups ( n = 16): G1, self-curing bulk-fill restorative system; G2, light-cured bulk-fill restorative system; and G3, conventional light-cured restorative system applied incrementally. Intact restored teeth were stored in artificial saliva for either 24 h or 18 months ( n = 8 per condition) and were sectioned only after completion of the respective aging period to obtain five beam-shaped specimens (≈ 0.9 mm²). The tooth was considered the experimental unit. Specimens were stored for either 24 h or 18 months ( n = 8 per condition). µTBS was assessed at a crosshead speed of 1 mm/min, and failure modes were determined using stereomicroscopy, with representative samples analyzed by scanning electron microscopy. Data were subjected to two-way ANOVA and Tukey’s post hoc test (α = 0.05). Bond strength was significantly influenced by both restorative system and aging time ( p < 0.001). A significant interaction between restorative system and aging condition was also detected ( p < 0.001). G2 exhibited the lowest µTBS values and a higher prevalence of adhesive failures. In contrast, G1 showed bond strength comparable to G3 and significantly higher than G2. Cohesive failures predominated in G1 and G3, whereas adhesive failures were more frequent in G2. Within the limitations of this in vitro study, the self-curing bulk-fill restorative system demonstrated adhesive performance similar to the conventional restorative system and preserved its relative behavior after aging, under the respective adhesive strategies recommended by the manufacturers.
- 30 June 2026
- Published by Wiley in European Journal of Oral Sciences
- p. e70121
Effect of bioactive dentin modulators on adhesion of glass fiber posts
This study aimed to evaluate the effect of natural dentin modulators on the bond strength and adhesive interface of resin materials bonded to dentin oxidized by sodium hypochlorite. Forty bovine roots underwent endodontic treatment and were assigned to four groups: control gel, Libidibia ferrea 10% gel, Apis mellifera 10% gel, and sodium hypochlorite irrigation. Glass fiber posts were cemented using a universal adhesive system and dual‐cure resin cement. Bond strength was assessed by the push‐out test, and the failure pattern and resin tag penetration were also evaluated. The results showed that both L. ferrea and A. mellifera treatments enhanced bond strength and resin tag extension compared to the control and sodium hypochlorite groups, with no difference between the two natural modulators, regardless of the root canal third. Cohesive failures were more frequent in the natural modulator groups, whereas adhesive failures predominated in the control and sodium hypochlorite groups. The findings indicate that natural dentin modulators improved the adhesive performance of resin materials bonded to dentin previously oxidized by sodium hypochlorite.
- 30 June 2026
- Published by Wiley in European Journal of Oral Sciences
- p. e70121
Effect of bioactive dentin modulators on adhesion of glass fiber posts
This study aimed to evaluate the effect of natural dentin modulators on the bond strength and adhesive interface of resin materials bonded to dentin oxidized by sodium hypochlorite. Forty bovine roots underwent endodontic treatment and were assigned to four groups: control gel, Libidibia ferrea 10% gel, Apis mellifera 10% gel, and sodium hypochlorite irrigation. Glass fiber posts were cemented using a universal adhesive system and dual‐cure resin cement. Bond strength was assessed by the push‐out test, and the failure pattern and resin tag penetration were also evaluated. The results showed that both L. ferrea and A. mellifera treatments enhanced bond strength and resin tag extension compared to the control and sodium hypochlorite groups, with no difference between the two natural modulators, regardless of the root canal third. Cohesive failures were more frequent in the natural modulator groups, whereas adhesive failures predominated in the control and sodium hypochlorite groups. The findings indicate that natural dentin modulators improved the adhesive performance of resin materials bonded to dentin previously oxidized by sodium hypochlorite.