Xin Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xin Zhang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Chengwei Zuo
Southwest Petroleum University
3 shared publications - Juan Du
Southwest Petroleum University
3 shared publications - Pingli Liu
Southwest Petroleum University
3 shared publications Renyin Zhao
Southwest Petroleum University
2 shared publications- Xiang Chen
Southwest Petroleum University
2 shared publications Yixiang Qu
Southwest Petroleum University
2 shared publications
Latest Publications
- 3 October 2026
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 9 (41) , 19429-19439
Mesoporous Silica Microspheres in a Delayed Gel-Breaking System for High-Temperature Fracturing Fluid
In high-temperature fracturing operations, the rapid decomposition of strong oxidant breakers causes premature viscosity loss of fracturing fluids, severely impairing proppant placement. Currently, most delayed gel-breaking systems rely on polymeric shell materials to physically encapsulate oxidants. However, such polymer-based systems suffer from a dual failure mechanism at elevated temperatures: (i) the polymer shell softens and swells due to intensified thermal motion, losing its structural integrity; and (ii) the encapsulated strong oxidant (e.g., ammonium persulfate) aggressively attacks the polymer backbone, causing oxidative degradation of the shell material and accelerating burst release. These two synergistic effects render “polymer-encapsulated oxidants” fundamentally unworkable in high-temperature reservoirs. To radically overcome this material bottleneck, we propose for the first time a non-polymeric controlled-release strategy based on the synergistic effect of “inorganic mesoporous confinement and oil-phase isolation.” Rigid hollow mesoporous silica microspheres (HMSS) with nanoscale mesoporous shells are employed as inorganic structural carriers, which exhibit exceptional resistance to both high temperature and strong oxidants. APS is loaded via impregnation, followed by hydrophobic surface modification and dispersion in white oil to construct an emulsion-type release system. This system leverages the rigid silica skeleton for outstanding thermal and chemical stability, while the oil-phase interfacial barrier effectively prevents premature APS-aqueous contact. Results show that at 90 °C with 2.5 wt % hydrophobic particles, the cumulative release reaches 62% over 12 h, demonstrating excellent sustained-release characteristics. At 100 °C, the system extends the complete gel-breaking time to ∼8 h, which is 7 times longer (i.e., an 8-fold increase) than that of directly added APS. By completely abandoning organic polymer shellswhich are both thermally labile and susceptible to oxidative attackand instead employing inorganic mesoporous silica combined with an oil-phase barrier, this work fundamentally resolves the long-standing challenge of premature breaker release under high-temperature oxidizing conditions, offering a nanoscale carrier-based, structurally simple, highly robust, and precision-release paradigm for deep high-temperature reservoir stimulation.
- 3 October 2026
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 9 (41) , 19429-19439
Mesoporous Silica Microspheres in a Delayed Gel-Breaking System for High-Temperature Fracturing Fluid
In high-temperature fracturing operations, the rapid decomposition of strong oxidant breakers causes premature viscosity loss of fracturing fluids, severely impairing proppant placement. Currently, most delayed gel-breaking systems rely on polymeric shell materials to physically encapsulate oxidants. However, such polymer-based systems suffer from a dual failure mechanism at elevated temperatures: (i) the polymer shell softens and swells due to intensified thermal motion, losing its structural integrity; and (ii) the encapsulated strong oxidant (e.g., ammonium persulfate) aggressively attacks the polymer backbone, causing oxidative degradation of the shell material and accelerating burst release. These two synergistic effects render “polymer-encapsulated oxidants” fundamentally unworkable in high-temperature reservoirs. To radically overcome this material bottleneck, we propose for the first time a non-polymeric controlled-release strategy based on the synergistic effect of “inorganic mesoporous confinement and oil-phase isolation.” Rigid hollow mesoporous silica microspheres (HMSS) with nanoscale mesoporous shells are employed as inorganic structural carriers, which exhibit exceptional resistance to both high temperature and strong oxidants. APS is loaded via impregnation, followed by hydrophobic surface modification and dispersion in white oil to construct an emulsion-type release system. This system leverages the rigid silica skeleton for outstanding thermal and chemical stability, while the oil-phase interfacial barrier effectively prevents premature APS-aqueous contact. Results show that at 90 °C with 2.5 wt % hydrophobic particles, the cumulative release reaches 62% over 12 h, demonstrating excellent sustained-release characteristics. At 100 °C, the system extends the complete gel-breaking time to ∼8 h, which is 7 times longer (i.e., an 8-fold increase) than that of directly added APS. By completely abandoning organic polymer shellswhich are both thermally labile and susceptible to oxidative attackand instead employing inorganic mesoporous silica combined with an oil-phase barrier, this work fundamentally resolves the long-standing challenge of premature breaker release under high-temperature oxidizing conditions, offering a nanoscale carrier-based, structurally simple, highly robust, and precision-release paradigm for deep high-temperature reservoir stimulation.
- 17 July 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (15) , 12273-12284
Preparation of Ultratemperature-Resistant Cleaning Thickener and Research on the Mechanism of Acid Resistance
Acidizing systems are widely employed in the exploitation of carbonate reservoirs. However, the reaction kinetics of conventional hydrochloric acid are excessively rapid, and the penetration distance is limited. To address these issues, a purely cationic thickening polymer, ADDD, was designed and synthesized for ultrahigh-temperature reservoirs based on supramolecular interaction principles. The electrostatic repulsion between cationic groups alleviates the compression of the polymer’s electric double layer by H+, while the hydrophobic association structure imparts rigidity and thermal resistance to the polymer. The substitution of dimethyl diallyl ammonium chloride (DMDAAC) for the commonly used AMPS monomer further reinforces the polymer backbone, significantly enhancing its heat resistance, acid resistance, and compatibility with carbonate reservoirs. At 180 °C and a shear rate of 170 s–1, the viscosities of 15 and 20 wt % ADDD gelled acids stabilized at 40 mPa·s and 35 mPa·s, respectively, after 120 min of shear treatment. The gelled acid retained 45.83% of its viscosity after aging at 180 °C for 4 h. Its corrosion rate on P110SS was only 9.38 g/(m2·h), corresponding to 9.73% and 15.27% of the rates observed for hydrochloric acid and AE gelled acid at the same concentration, respectively. Under conditions of 180 °C and 300 rpm, the acid–rock reaction rate of ADDD gelled acid was reduced to merely 12.5% and 50.68% of those of hydrochloric acid and AE gelled acid, respectively. The residual acid exhibited a viscosity as low as 1 mPa·s, and no obvious precipitation was observed. After breaking with 0.05 wt % ammonium persulfate at 180 °C, the viscosity of the ADDD gelled acid dropped to 1.5 mPa·s. The conformational differences between ADDD and AE in acidic media were collaboratively elucidated through zeta potential measurements and dynamic light scattering (DLS) analysis. Molecular dynamics simulations combined with analyses of H+ diffusion coefficients, binding energies, and radial distribution functions revealed that hydrophobic association and cationic electrostatic effects synergistically enhance acid resistance and suppress acid–rock reaction rates. Meanwhile, electrostatic repulsion effectively prevented the incompatibility issues of the corrosion inhibitor that arise from amide thermal degradation under high-temperature conditions. The acid- and temperature-resistant thickener synthesized in this study provides technical and theoretical support for the development of ultrahigh-temperature carbonate reservoirs.
- 17 July 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (15) , 12273-12284
Preparation of Ultratemperature-Resistant Cleaning Thickener and Research on the Mechanism of Acid Resistance
Acidizing systems are widely employed in the exploitation of carbonate reservoirs. However, the reaction kinetics of conventional hydrochloric acid are excessively rapid, and the penetration distance is limited. To address these issues, a purely cationic thickening polymer, ADDD, was designed and synthesized for ultrahigh-temperature reservoirs based on supramolecular interaction principles. The electrostatic repulsion between cationic groups alleviates the compression of the polymer’s electric double layer by H+, while the hydrophobic association structure imparts rigidity and thermal resistance to the polymer. The substitution of dimethyl diallyl ammonium chloride (DMDAAC) for the commonly used AMPS monomer further reinforces the polymer backbone, significantly enhancing its heat resistance, acid resistance, and compatibility with carbonate reservoirs. At 180 °C and a shear rate of 170 s–1, the viscosities of 15 and 20 wt % ADDD gelled acids stabilized at 40 mPa·s and 35 mPa·s, respectively, after 120 min of shear treatment. The gelled acid retained 45.83% of its viscosity after aging at 180 °C for 4 h. Its corrosion rate on P110SS was only 9.38 g/(m2·h), corresponding to 9.73% and 15.27% of the rates observed for hydrochloric acid and AE gelled acid at the same concentration, respectively. Under conditions of 180 °C and 300 rpm, the acid–rock reaction rate of ADDD gelled acid was reduced to merely 12.5% and 50.68% of those of hydrochloric acid and AE gelled acid, respectively. The residual acid exhibited a viscosity as low as 1 mPa·s, and no obvious precipitation was observed. After breaking with 0.05 wt % ammonium persulfate at 180 °C, the viscosity of the ADDD gelled acid dropped to 1.5 mPa·s. The conformational differences between ADDD and AE in acidic media were collaboratively elucidated through zeta potential measurements and dynamic light scattering (DLS) analysis. Molecular dynamics simulations combined with analyses of H+ diffusion coefficients, binding energies, and radial distribution functions revealed that hydrophobic association and cationic electrostatic effects synergistically enhance acid resistance and suppress acid–rock reaction rates. Meanwhile, electrostatic repulsion effectively prevented the incompatibility issues of the corrosion inhibitor that arise from amide thermal degradation under high-temperature conditions. The acid- and temperature-resistant thickener synthesized in this study provides technical and theoretical support for the development of ultrahigh-temperature carbonate reservoirs.
- 14 July 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (29) , 21124-21138
Bioinspired by Mussels: Construction of an Ultrasalt-Tolerant, Tunable-Viscosity Slickwater Fracturing Fluid for the Reuse of Deep Coalbed Methane Flowback Fluids
The extraction of deep coalbed methane (CBM) relies on high-rate, large-volume network fracturing. In water-scarce regions, recycling formation flowback fluids for fracturing fluid preparation is essential to reduce freshwater consumption. To address the performance degradation of fracturing fluids in high-salinity flowback water, a biomimetic salt-tolerant polymer friction reducer (ASD) was developed, inspired by the zwitterionic salt-resistance mechanism in mussels. By integrating hydrophobic association with the antipolyelectrolyte effect, the ASD-based slickwater maintains an apparent viscosity of ∼75 mPa·s in flowback water with total dissolved solids exceeding 120,000 mg/L. Experimental results demonstrate a maximum drag reduction rate of 79.58% and superior dynamic proppant transport. At 60 °C, the fluid completely breaks within 3 h, leaving a low residue of 310 mg/L. Mechanistically, particle size and zeta-potential analyses confirm that ASD exhibits a significant increase in hydrated radius (500–2000 nm) in saline solutions, far exceeding the 10–35 nm observed for conventional hydrolyzed polyacrylamide, validating its strong antipolyelectrolyte response. Molecular dynamics simulations further elucidate this structural adaptability in high salt solutions. This biomimetic strategy offers a high-performance, sustainable solution for deep CBM stimulation using hypersaline flowback water.
- 14 July 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (29) , 21124-21138
Bioinspired by Mussels: Construction of an Ultrasalt-Tolerant, Tunable-Viscosity Slickwater Fracturing Fluid for the Reuse of Deep Coalbed Methane Flowback Fluids
The extraction of deep coalbed methane (CBM) relies on high-rate, large-volume network fracturing. In water-scarce regions, recycling formation flowback fluids for fracturing fluid preparation is essential to reduce freshwater consumption. To address the performance degradation of fracturing fluids in high-salinity flowback water, a biomimetic salt-tolerant polymer friction reducer (ASD) was developed, inspired by the zwitterionic salt-resistance mechanism in mussels. By integrating hydrophobic association with the antipolyelectrolyte effect, the ASD-based slickwater maintains an apparent viscosity of ∼75 mPa·s in flowback water with total dissolved solids exceeding 120,000 mg/L. Experimental results demonstrate a maximum drag reduction rate of 79.58% and superior dynamic proppant transport. At 60 °C, the fluid completely breaks within 3 h, leaving a low residue of 310 mg/L. Mechanistically, particle size and zeta-potential analyses confirm that ASD exhibits a significant increase in hydrated radius (500–2000 nm) in saline solutions, far exceeding the 10–35 nm observed for conventional hydrolyzed polyacrylamide, validating its strong antipolyelectrolyte response. Molecular dynamics simulations further elucidate this structural adaptability in high salt solutions. This biomimetic strategy offers a high-performance, sustainable solution for deep CBM stimulation using hypersaline flowback water.