Mohammad Shehada
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammad Shehada has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Tahel Oguen Alon
Department of Prosthodontics, School of Graduate Dentistry, Rambam Health Care Campus (RHCC), Haifa 3525408, Israel
1 shared publication - Yaniv Mayer
The Ruth and Bruce Rappaport Faculty of Medicine, Technion - Israel Institute of Technology, Haifa, Israel; Department of Periodontology, Rambam Health Care Campus, Haifa, Israel
1 shared publication - Yaniv Skvirsky
Department of Prosthodontics, School of Graduate Dentistry, Rambam Health Care Campus, Haifa 3525408, Israel
1 shared publication - Zvi Gutmacher
Department of Prosthodontics, School of Graduate Dentistry, Rambam Health Care Campus (RHCC), Haifa 3525408, Israel
1 shared publication
Latest Publications
- Open Access
- 20 July 2026
- Published by MDPI AG in Dentistry Journal
- Vol. 14 (7) , 454
Dimensional Stability of Printed Dental Model: Stability over Time at Different Storage Temperatures
Background and Objectives: Dental models are essential for diagnosis and prosthetic treatment planning and have traditionally been fabricated from gypsum. With the growing adoption of digital workflows, 3D-printed dental models are increasingly used; however, concerns remain regarding their dimensional stability over time. This study evaluated the temporal dimensional changes of gypsum and 3D-printed dental models under different storage conditions and assessed the uniformity of these changes across the models. Methods: A fully dentate maxillary typodont was scanned to create a reference model. Sixteen gypsum casts (Type IV dental stone) and 48 3D-printed models from three materials were fabricated. Models were stored at either 4 °C or room temperature and rescanned at predefined intervals over 28 days. Dimensional accuracy was analyzed using 3D inspection software (Geomagic Control X 2022.1.0), with trueness measured by root mean square deviation and precision by standard deviation across the full arch and five predefined regions. Statistical analysis was performed using a Bayesian hierarchical linear model, with significance set at pd > 97.5%. Results: Printed models demonstrated significantly higher precision than gypsum models at baseline and day 28 under both storage conditions, with no significant differences among printed materials. In terms of trueness, selected printed groups showed lower deviations than gypsum at baseline, while one material exhibited the best performance at day 28. Gypsum models remained relatively stable over time, whereas printed models showed time-dependent, region-specific dimensional changes, primarily in posterior regions, with maximum deviations of up to 0.026 mm. Conclusions: 3D-printed dental models exhibit limited but nonuniform dimensional changes over time, while gypsum models remain comparatively stable. Localized distortions, particularly in posterior regions, should be considered when printed models are used for precise prosthetic applications.
- 20 July 2026
- Published by MDPI AG in Dentistry Journal
- Vol. 14 (7) , 454
Open AccessDimensional Stability of Printed Dental Model: Stability over Time at Different Storage Temperatures
Background and Objectives: Dental models are essential for diagnosis and prosthetic treatment planning and have traditionally been fabricated from gypsum. With the growing adoption of digital workflows, 3D-printed dental models are increasingly used; however, concerns remain regarding their dimensional stability over time. This study evaluated the temporal dimensional changes of gypsum and 3D-printed dental models under different storage conditions and assessed the uniformity of these changes across the models. Methods: A fully dentate maxillary typodont was scanned to create a reference model. Sixteen gypsum casts (Type IV dental stone) and 48 3D-printed models from three materials were fabricated. Models were stored at either 4 °C or room temperature and rescanned at predefined intervals over 28 days. Dimensional accuracy was analyzed using 3D inspection software (Geomagic Control X 2022.1.0), with trueness measured by root mean square deviation and precision by standard deviation across the full arch and five predefined regions. Statistical analysis was performed using a Bayesian hierarchical linear model, with significance set at pd > 97.5%. Results: Printed models demonstrated significantly higher precision than gypsum models at baseline and day 28 under both storage conditions, with no significant differences among printed materials. In terms of trueness, selected printed groups showed lower deviations than gypsum at baseline, while one material exhibited the best performance at day 28. Gypsum models remained relatively stable over time, whereas printed models showed time-dependent, region-specific dimensional changes, primarily in posterior regions, with maximum deviations of up to 0.026 mm. Conclusions: 3D-printed dental models exhibit limited but nonuniform dimensional changes over time, while gypsum models remain comparatively stable. Localized distortions, particularly in posterior regions, should be considered when printed models are used for precise prosthetic applications.