Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ethem Furkan Hıdır has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Effects of Prosthodontic Treatment on Oral Tissues

    by Ethem Furkan Hıdır, Zeynep Ateş Hıdır, Sümeyye Coşgun Baybars

  • Current Dental Studies VI

    by Oğuz Yoldaş, Delil Doğan, Merve Güney, Çağdaş Gökçen, Özenç Beste Kandemir, Özge Özdal Zincir, Hasan Öksüzoğlu, Alev Ercan, Metehan Özdemir, Sefa Aydındoğan, et al.

  • Open Access

    Structure–Chemistry–Tribology Coupling and Artificial-Intelligence-Assisted Performance Prediction of Cubic Boron Nitride-Reinforced Heat-Polymerized PMMA Denture Base Composites

    by Ali Sincar, Ethem Furkan Hıdır, Cevher Kürşat Macit, Samet Tekin, Ukbe Usame Uçar, Fatih Osmanlıoğlu

    Heat-polymerized poly(methyl methacrylate) (PMMA) is widely used for denture bases but remains susceptible to surface deformation and sliding wear. This study evaluated the structure, chemistry, surface morphology, microhardness, and dry-sliding tribology of PMMA reinforced with 1, 3, and 5 wt.% cubic boron nitride (c-BN). Disk specimens (10 mm diameter × 2 mm thickness) were prepared; ten specimens per group were tested for Vickers microhardness and wear/coefficient of friction, while one representative specimen per group was examined by XRD, ATR-FTIR, and SEM/EDS before and after wear. The PMMA amorphous/semi-amorphous response and characteristic ester bands were retained, whereas c-BN-related diffraction features and B/N signals became more evident with reinforcement. Microhardness increased from 20.00 ± 0.70 to 45.00 ± 1.61 HV0.03. After 1000 m at 10 N and 1 m s−1, mass loss decreased from 32.4 to 9.8 mg and the overall coefficient of friction from 0.58 to 0.28. Post-wear SEM/EDS showed reduced grooving, smearing, and material detachment at higher c-BN contents. Statistical analysis confirmed large composition effects, and composition-window models reproduced the measured hardness and wear trends. Within the tested range, 5 wt.% c-BN provided the strongest surface-hardening and wear-suppression response under controlled dry-sliding conditions.

  • Open Access

    Hard-Particle Surface Stabilization and Data-Driven Wear Prediction in TiB2-Reinforced Heat-Polymerized PMMA Denture Base Composites

    by Ethem Furkan Hıdır, Ali Sincar, Cevher Kürşat Macit, Samet Tekin, Ukbe Usame Uçar

    Poly(methyl methacrylate) (PMMA) remains a clinically important denture base polymer because of its favorable processability, aesthetics, repairability and long-term prosthodontic use; however, its limited surface hardness and susceptibility to sliding-induced degradation constrain surface durability. This study establishes the structure–chemistry–microstructure–tribology relationships and composition-window predictive behavior of heat-polymerized PMMA reinforced with titanium diboride (TiB2). PMMA/TiB2 composites containing 1, 3 and 5 wt.% TiB2 were prepared and compared with unreinforced PMMA. X-ray diffraction confirmed preservation of the broad amorphous/semi-amorphous PMMA response, while TiB2-related crystalline features became increasingly detectable with reinforcement content. ATR-FTIR showed retention of the characteristic C–H, ester C=O and C–O/C–O–C vibrations. SEM/EDS demonstrated progressively greater particle-related surface contrast and local Ti/B-associated elemental signatures. Vickers microhardness increased from 20.0 ± 0.7 to 35.0 ± 1.39 HV0.03, corresponding to a 75.0% improvement at 5 wt.% TiB2. After 1000 m of dry sliding, total mass loss decreased from 32.4 ± 0.5 to 14.9 ± 0.4 mg (54.0% reduction), overall coefficient of friction decreased from 0.58 to 0.35, and representative wear-track width decreased from 481.4 to 101.8 µm. A parsimonious distance–composition interaction model retained strong grouped leave-one-composition-out performance for cumulative wear (R2 = 0.9622; RMSE = 1.53 mg), while a linear composition model provided the most robust hardness prediction (R2 = 0.9317; RMSE = 1.50 HV0.03). More complex nonlinear models did not improve prediction for held-out compositions. Within the investigated 0–5 wt.% window, 5 wt.% TiB2 provided the most effective combination of matrix preservation, surface hardening, wear suppression and frictional stabilization.