Jungmin Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jungmin Kim has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Dongwook Shin
Division of Materials Science & Engineering, Hanyang University, Seongdong-gu, Seoul 04763, Republic of Korea
2 shared publications Dongwook Shin
1 shared publication- Sangho Park
Division of Materials Science & Engineering, Hanyang University, Seongdong-gu, Seoul 04763, Republic of Korea
1 shared publication - Seung Kwon Lee1 shared publication
- Sewook Lee
Division of Materials Science & Engineering, Hanyang University, Seongdong-gu, Seoul 04763, Republic of Korea
1 shared publication Sungjae Kim
1 shared publication
Latest Publications
- Open Access
Porous Poly(4-vinylpyridine) Coatings Prepared by Electrostatic Slurry Spray Deposition: Morphological Control and Preliminary Formaldehyde-Reduction Assessment
Porous poly(4-vinylpyridine) (P4VP) coatings were fabricated by electrostatic slurry spray deposition (ESSD) using solution and ethanol–water composite-slurry precursors. Thirty-four solvents were screened to examine the relationship between precursor formulation, spray behavior, and deposited morphology. Gradual nonsolvent addition generated a particulate composite slurry, with a principal volume-weighted dynamic light scattering (DLS) peak at 13.78 nm for the 7.4 wt.% formulation. Under the investigated conditions, this slurry produced a more spatially uniform porous coating than the solution precursor and was successfully deposited onto a three-dimensional fibrous filter scaffold. During a preliminary 30 m3 chamber assessment of the air-purifier system equipped with the coated filter, formaldehyde (HCHO) concentration decreased from 0.846 to 0.702 ppm in 1 h, corresponding to an apparent concentration-decay-based air-cleaning rate (Qapp) of approximately 5.69 m3 h−1. This preliminary observation describes the performance of the assembled air-purifier system; the principal contribution of the study is the formulation and morphological control of porous P4VP coatings through composite-slurry ESSD.
Open AccessPorous Poly(4-vinylpyridine) Coatings Prepared by Electrostatic Slurry Spray Deposition: Morphological Control and Preliminary Formaldehyde-Reduction Assessment
Porous poly(4-vinylpyridine) (P4VP) coatings were fabricated by electrostatic slurry spray deposition (ESSD) using solution and ethanol–water composite-slurry precursors. Thirty-four solvents were screened to examine the relationship between precursor formulation, spray behavior, and deposited morphology. Gradual nonsolvent addition generated a particulate composite slurry, with a principal volume-weighted dynamic light scattering (DLS) peak at 13.78 nm for the 7.4 wt.% formulation. Under the investigated conditions, this slurry produced a more spatially uniform porous coating than the solution precursor and was successfully deposited onto a three-dimensional fibrous filter scaffold. During a preliminary 30 m3 chamber assessment of the air-purifier system equipped with the coated filter, formaldehyde (HCHO) concentration decreased from 0.846 to 0.702 ppm in 1 h, corresponding to an apparent concentration-decay-based air-cleaning rate (Qapp) of approximately 5.69 m3 h−1. This preliminary observation describes the performance of the assembled air-purifier system; the principal contribution of the study is the formulation and morphological control of porous P4VP coatings through composite-slurry ESSD.
- Open Access
Electrospray as an Atomized Precursor-Delivery Strategy for Stöber Silica Nanosphere Synthesis
Electrospray provides an atomized precursor delivery strategy for controlling silica particle formation during Stöber synthesis. In this study, electrospray and drop-by-drop precursor delivery were compared across 0.1–0.5 mL/min to evaluate delivery-mode effects on particle size and size distribution. The mean particle size increased with flow rate under electrospray delivery, whereas the opposite trend was observed under drop-by-drop delivery. Electrospray maintained relatively narrow particle size distributions, with coefficients of variation ranging from 5.6 to 6.7%. These contrasting behaviors were interpreted in terms of differences in local precursor supply conditions and their possible influence on the relative contributions of particle growth and secondary nucleation. Under stable cone-jet electrospray conditions, the mean particle size increased progressively with reaction time at both 7.8 and 9.3 kV, while the coefficient of variation remained approximately 7% throughout. In addition, particles synthesized at 9.3 kV exhibited smaller mean diameters than those obtained at 7.8 kV at all investigated reaction times, while maintaining relatively narrow particle size distributions under both stable cone-jet conditions. Overall, these findings suggest that electrospray offers an additional process-based approach for adjusting silica particle size through control of precursor supply rate and atomization characteristics.
Open AccessElectrospray as an Atomized Precursor-Delivery Strategy for Stöber Silica Nanosphere Synthesis
Electrospray provides an atomized precursor delivery strategy for controlling silica particle formation during Stöber synthesis. In this study, electrospray and drop-by-drop precursor delivery were compared across 0.1–0.5 mL/min to evaluate delivery-mode effects on particle size and size distribution. The mean particle size increased with flow rate under electrospray delivery, whereas the opposite trend was observed under drop-by-drop delivery. Electrospray maintained relatively narrow particle size distributions, with coefficients of variation ranging from 5.6 to 6.7%. These contrasting behaviors were interpreted in terms of differences in local precursor supply conditions and their possible influence on the relative contributions of particle growth and secondary nucleation. Under stable cone-jet electrospray conditions, the mean particle size increased progressively with reaction time at both 7.8 and 9.3 kV, while the coefficient of variation remained approximately 7% throughout. In addition, particles synthesized at 9.3 kV exhibited smaller mean diameters than those obtained at 7.8 kV at all investigated reaction times, while maintaining relatively narrow particle size distributions under both stable cone-jet conditions. Overall, these findings suggest that electrospray offers an additional process-based approach for adjusting silica particle size through control of precursor supply rate and atomization characteristics.