Chang Peng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chang Peng has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Bao Yang
Department of Engineering Mechanics, School of Civil Engineering and Transportation, South China University of Technology, Guangzhou 510640, China
2 shared publications - Zhenyu Jiang
Department of Engineering Mechanics, School of Civil Engineering and Transportation, South China University of Technology, Guangzhou 510640, China
2 shared publications - Fuwang Zhao
Department of Mechanical Engineering, The Hong Kong Polytechnic University 1 , Kowloon, Hong Kong, China
1 shared publication - Ge Zhang
School of Civil and Transportation Engineering, Guangdong University of Technology, Guangzhou 510006, China
1 shared publication - Hui Sun
Guangdong Provincial Academy of Building Research Group Co., Ltd., Guangzhou 510510, China
1 shared publication - Jinli Piao
School of Fashion and Textiles, The Hong Kong Polytechnic University, Kowloon, Hong Kong SAR, China
1 shared publication
Latest Publications
- Open Access
High-Performance Riveted Complementary-Structure Rotating Triboelectric Nanogenerator for Energy Harvesting from Slow-Speed Water Flows
Triboelectric nanogenerators (TENGs) are promising for harvesting low-frequency mechanical energy, but rotating TENGs (R-TENGs) driven by low-speed water flow remain constrained by limited driving torque, sliding-contact losses, and rotating-system stability. Here, a three-dimensional (3D) riveted complementary-structure rotating triboelectric nanogenerator (RCSR-TENG) is proposed for low-speed water-flow energy harvesting. A semi-analytical formulation incorporating a force-dependent real-contact fraction is developed to describe the coupled relationships among output voltage, transferred charge, rotation angle, and contact force. Because the contact parameters were not independently calibrated, the formulation is used for sensitivity and trend analysis rather than as a quantitatively validated predictive model. For the single prototype tested for each configuration, at 1000 rpm under the fixed effective measurement load of 9 MΩ, the RCSR-TENG produced a peak output power of 544 μW, compared with 304 μW for the flat R-TENG, representing an increase of approximately 79%. The same RCSR-TENG prototype maintained a stable voltage amplitude of over 150,000 rotation cycles. When coupled to a fully passive flapping-foil collector in a 0.55 m s−1 water flow, the system generated periodic electrical output with a peak area-normalized power exceeding 5000 μW m−2. These results demonstrate the structural-performance advantage of the riveted complementary design and its proof-of-concept applicability to low-speed water-flow energy harvesting.
Open AccessHigh-Performance Riveted Complementary-Structure Rotating Triboelectric Nanogenerator for Energy Harvesting from Slow-Speed Water Flows
Triboelectric nanogenerators (TENGs) are promising for harvesting low-frequency mechanical energy, but rotating TENGs (R-TENGs) driven by low-speed water flow remain constrained by limited driving torque, sliding-contact losses, and rotating-system stability. Here, a three-dimensional (3D) riveted complementary-structure rotating triboelectric nanogenerator (RCSR-TENG) is proposed for low-speed water-flow energy harvesting. A semi-analytical formulation incorporating a force-dependent real-contact fraction is developed to describe the coupled relationships among output voltage, transferred charge, rotation angle, and contact force. Because the contact parameters were not independently calibrated, the formulation is used for sensitivity and trend analysis rather than as a quantitatively validated predictive model. For the single prototype tested for each configuration, at 1000 rpm under the fixed effective measurement load of 9 MΩ, the RCSR-TENG produced a peak output power of 544 μW, compared with 304 μW for the flat R-TENG, representing an increase of approximately 79%. The same RCSR-TENG prototype maintained a stable voltage amplitude of over 150,000 rotation cycles. When coupled to a fully passive flapping-foil collector in a 0.55 m s−1 water flow, the system generated periodic electrical output with a peak area-normalized power exceeding 5000 μW m−2. These results demonstrate the structural-performance advantage of the riveted complementary design and its proof-of-concept applicability to low-speed water-flow energy harvesting.
- Open Access
- 8 August 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (16) , 7912
Deep Learning-Based Cross-Verification for Road Subsurface Distress Detection Driven by Field Data of 3D Ground-Penetrating Radar
Ground-penetrating radar (GPR) is a rapid and non-destructive technique for road sub-surface distress (RSD) detection. However, reliable interpretation of GPR images remains challenging because subsurface anomalies often present weak boundaries, ambiguous textures, and high similarity to non-distress targets. This study proposes a cross-verification intelligent algorithm that exploits complementary information from different views of 3D GPR data. Three YOLO-based detectors are trained on view-specific GPR images to identify RSD-related targets, including voids, loose structures, and manholes. By sequentially verifying detection results across different views, the proposed method improves recognition reliability under vague subsurface imaging conditions. The models are trained and evaluated on an expert-annotated field 3D GPR dataset containing 2134 location-level multi-view samples. At the selected operational thresholds, the complete cross-verification procedure achieved 95.9% precision and 98.6% recall for RSD detection in the testing subset. In a field evaluation on 15 roads, all 69 RSD locations in the expert-identified reference set were matched by automatic indications. When integrated into an automatic detection system, the method reduced manual inspection workloads by approximately 90% while maintaining high field reliability. These results demonstrate the potential of multi-view cross-verification for post-survey RSD screening and expert-assisted review.
- 8 August 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (16) , 7912
Open AccessDeep Learning-Based Cross-Verification for Road Subsurface Distress Detection Driven by Field Data of 3D Ground-Penetrating Radar
Ground-penetrating radar (GPR) is a rapid and non-destructive technique for road sub-surface distress (RSD) detection. However, reliable interpretation of GPR images remains challenging because subsurface anomalies often present weak boundaries, ambiguous textures, and high similarity to non-distress targets. This study proposes a cross-verification intelligent algorithm that exploits complementary information from different views of 3D GPR data. Three YOLO-based detectors are trained on view-specific GPR images to identify RSD-related targets, including voids, loose structures, and manholes. By sequentially verifying detection results across different views, the proposed method improves recognition reliability under vague subsurface imaging conditions. The models are trained and evaluated on an expert-annotated field 3D GPR dataset containing 2134 location-level multi-view samples. At the selected operational thresholds, the complete cross-verification procedure achieved 95.9% precision and 98.6% recall for RSD detection in the testing subset. In a field evaluation on 15 roads, all 69 RSD locations in the expert-identified reference set were matched by automatic indications. When integrated into an automatic detection system, the method reduced manual inspection workloads by approximately 90% while maintaining high field reliability. These results demonstrate the potential of multi-view cross-verification for post-survey RSD screening and expert-assisted review.