JPJinli Piao

Jinli Piao

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jinli Piao has a total of 17 co-authors. Here are the top co-authors by number of shared publications:

  • Bao Yang

    Department of Engineering Mechanics, School of Civil Engineering and Transportation, South China University of Technology, Guangzhou 510640, China

    1 shared publication
  • Chang Peng

    Department of Engineering Mechanics, School of Civil Engineering and Transportation, South China University of Technology, Guangzhou 510640, China

    1 shared publication
  • Fuwang Zhao

    Department of Mechanical Engineering, The Hong Kong Polytechnic University 1 , Kowloon, Hong Kong, China

    1 shared publication
  • Guosai Liu

    Research Institute for Intelligent Wearable Systems School of Fashion and Textiles The Hong Kong Polytechnic University Kowloon 999077 China

    1 shared publication
  • Jing Yang

    Research Institute for Intelligent Wearable Systems School of Fashion and Textiles The Hong Kong Polytechnic University Kowloon 999077 China

    1 shared publication
  • Li-Sha Zhang

    Research Institute for Intelligent Wearable Systems, School of Fashion and Textiles, The Hong Kong Polytechnic University, Hong Kong, China

    1 shared publication

Latest Publications

  • Open Access

    High-Performance Riveted Complementary-Structure Rotating Triboelectric Nanogenerator for Energy Harvesting from Slow-Speed Water Flows

    by Bao Yang, Chang Peng, Zihao Wang, Fuwang Zhao, Licheng Zhou, Zhenyu Jiang, Yiping Liu, Liqun Tang, Zejia Liu, Jinli Piao

    Triboelectric nanogenerators (TENGs) are promising for harvesting low-frequency mechanical energy, but rotating TENGs (R-TENGs) driven by low-speed water flow remain constrained by limited driving torque, sliding-contact losses, and rotating-system stability. Here, a three-dimensional (3D) riveted complementary-structure rotating triboelectric nanogenerator (RCSR-TENG) is proposed for low-speed water-flow energy harvesting. A semi-analytical formulation incorporating a force-dependent real-contact fraction is developed to describe the coupled relationships among output voltage, transferred charge, rotation angle, and contact force. Because the contact parameters were not independently calibrated, the formulation is used for sensitivity and trend analysis rather than as a quantitatively validated predictive model. For the single prototype tested for each configuration, at 1000 rpm under the fixed effective measurement load of 9 MΩ, the RCSR-TENG produced a peak output power of 544 μW, compared with 304 μW for the flat R-TENG, representing an increase of approximately 79%. The same RCSR-TENG prototype maintained a stable voltage amplitude of over 150,000 rotation cycles. When coupled to a fully passive flapping-foil collector in a 0.55 m s−1 water flow, the system generated periodic electrical output with a peak area-normalized power exceeding 5000 μW m−2. These results demonstrate the structural-performance advantage of the riveted complementary design and its proof-of-concept applicability to low-speed water-flow energy harvesting.

  • Open Access

    Wearable Fluidic Fabric with Excellent Heat Transfer Performance for Sports Recovery

    by Jing Yang, Ying Xiong, Jinli Piao, Manyui Leung, Guosai Liu, Mingyue Zhu, Shengyang Tang, Lisha Zhang, Xiaoming Tao

    Rapid temperature contrast hydrotherapy by water immersion has been utilized by athletes for effective sports recovery. However, its application at some training or competition venues is limited by high water consumption, bucky size, personal hygiene, and inconvenience. Here, a novel portable system equipped with highly effective, lightweight, and hygienic wearable fluidic fabric device is reported, that replaces direct water immersion. The measured heat transfer coefficient between the skin and the fabric is 98.5 W m−2 K−1, which is 92% of that in direct water immersion at 10 °C and significantly higher than that by previously reported cooling garments. The core layer, a flexible heat transfer panel (FHTP), can switch between cold and hot modes (5–40 °C) over an area of 0.3 m2. The contact condition between skin and the deformable FHTP has been considered in a new verified heat transfer model. Optimization of the parameters has resulted in excellent heat transfer performance. This fluidic fabric also holds potential in diverse applications, such as enhancing thermal safety and comfort in extreme environments (e.g., personal thermal management systems and fire‐protection suits), supporting cryotherapy and thermotherapy in rehabilitation and healthcare, and simulation of total tactile sensations in virtual reality.