Mengqian Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mengqian Wang has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Jinliang Song
2 shared publicationsPengfei Lian
2 shared publications- Anrui Li
School of Materials Science and Engineering, Shanghai University, Shanghai 200072, China
1 shared publication - Delun Zhu
Shaoxing Institute of Technology, Shanghai University, Shaoxing 312000, China
1 shared publication Hailong Gao
1 shared publicationHefei Huang
1 shared publication
Latest Publications
- 21 September 2026
- Published by Elsevier in Corrosion Science
- Vol. 272
Temperature-dependent non-stoichiometry SiC coatings on nuclear graphite and its molten salt corrosion mechanism
- 21 September 2026
- Published by Elsevier in Corrosion Science
- Vol. 272
Temperature-dependent non-stoichiometry SiC coatings on nuclear graphite and its molten salt corrosion mechanism
- Open Access
Pore Structure Regulation of RF-Derived Porous Carbons Using a Mixed-Level Design of Experiments for Lithium-Ion Battery Anode Materials
Resorcinol–formaldehyde (RF)-derived porous carbons have attracted considerable attention as anode materials for lithium-ion batteries because of their tunable pore structures and continuous carbon frameworks. However, conventional one-factor-at-a-time experiments do not readily allow the relative effects of multiple preparation factors to be systematically compared within a unified experimental framework. In this study, a mixed-level Design of Experiments (DOE) was employed to systematically investigate the effects of solid content, gelation temperature, R/C ratio, combined gelation and acid-washing/aging times, and drying method on the BET specific surface area, total pore volume, and dominant pore size of RF-derived porous carbons. Representative preparation conditions were subsequently selected to prepare PC-1 and PC-2. Both samples exhibited predominantly amorphous mesoporous carbon structures and similar electrochemical response profiles. PC-1 exhibited a higher reversible specific capacity and slightly more favorable electrochemical kinetics. These concurrent observations suggest an association between the pore-structure characteristics and electrochemical behavior of the selected samples. PC-1 delivered an initial charge capacity of 416.67 mAh g−1 with an initial Coulombic efficiency of 79.31%. After 200 cycles at 0.1 A g−1, it retained a reversible capacity of 307.86 mAh g−1, corresponding to a capacity retention of 88.64% relative to the second-cycle charge capacity. These results indicate that, within the investigated design space, the DOE approach provides an exploratory basis for jointly comparing the statistical evidence and practical effect magnitudes of the preparation factors and for selecting representative candidates with favorable pore-structure characteristics. The integration of DOE-based factor screening with subsequent structural and electrochemical validation provides an experimentally grounded framework for relating preparation parameters to pore-structure responses and lithium-storage behavior, thereby supporting the rational development of RF-derived porous carbon anodes for lithium-ion batteries.
Open AccessPore Structure Regulation of RF-Derived Porous Carbons Using a Mixed-Level Design of Experiments for Lithium-Ion Battery Anode Materials
Resorcinol–formaldehyde (RF)-derived porous carbons have attracted considerable attention as anode materials for lithium-ion batteries because of their tunable pore structures and continuous carbon frameworks. However, conventional one-factor-at-a-time experiments do not readily allow the relative effects of multiple preparation factors to be systematically compared within a unified experimental framework. In this study, a mixed-level Design of Experiments (DOE) was employed to systematically investigate the effects of solid content, gelation temperature, R/C ratio, combined gelation and acid-washing/aging times, and drying method on the BET specific surface area, total pore volume, and dominant pore size of RF-derived porous carbons. Representative preparation conditions were subsequently selected to prepare PC-1 and PC-2. Both samples exhibited predominantly amorphous mesoporous carbon structures and similar electrochemical response profiles. PC-1 exhibited a higher reversible specific capacity and slightly more favorable electrochemical kinetics. These concurrent observations suggest an association between the pore-structure characteristics and electrochemical behavior of the selected samples. PC-1 delivered an initial charge capacity of 416.67 mAh g−1 with an initial Coulombic efficiency of 79.31%. After 200 cycles at 0.1 A g−1, it retained a reversible capacity of 307.86 mAh g−1, corresponding to a capacity retention of 88.64% relative to the second-cycle charge capacity. These results indicate that, within the investigated design space, the DOE approach provides an exploratory basis for jointly comparing the statistical evidence and practical effect magnitudes of the preparation factors and for selecting representative candidates with favorable pore-structure characteristics. The integration of DOE-based factor screening with subsequent structural and electrochemical validation provides an experimentally grounded framework for relating preparation parameters to pore-structure responses and lithium-storage behavior, thereby supporting the rational development of RF-derived porous carbon anodes for lithium-ion batteries.
- Open Access
- 21 August 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of graphite substrate roughness on microstructure and adhesion strength of CVD SiC coatings
Silicon carbide (SiC) coatings are essential for nuclear graphite in molten salt reactors due to their ability to suppress molten salt infiltration. However, the role of substrate roughness in regulating interfacial adhesion remains unclear. In this study, SiC coatings were deposited via chemical vapor deposition on nuclear graphite substrates with controlled roughness (Ra = 6.2, 1.0, and 0.4 μm), and the effects of roughness on microstructure and adhesion were systematically evaluated. A nonlinear dependence of coating performance on surface roughness was identified. Moderate roughness (Ra = 1.0 μm) yielded dense and well-crystallized coatings with smaller and more uniform grain aggregates (~9.45 μm) and minimal interfacial defects, resulting in the highest adhesion strength (Lc₁ = 62.2 N) and superior thermal shock resistance. In contrast, excessive roughness induced irregular aggregates and infiltration-related defects, leading to premature interfacial failure, whereas overly smooth surfaces weakened mechanical interlocking and physical adsorption, thereby reducing adhesion strength. A coupled mechanism involving mechanical interlocking, chemical diffusion, and stress dispersion was elucidated, demonstrating that optimal roughness governs interfacial integrity. These findings provide critical guidance for substrate pretreatment of SiC coatings in nuclear applications.
- 21 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of graphite substrate roughness on microstructure and adhesion strength of CVD SiC coatings
Silicon carbide (SiC) coatings are essential for nuclear graphite in molten salt reactors due to their ability to suppress molten salt infiltration. However, the role of substrate roughness in regulating interfacial adhesion remains unclear. In this study, SiC coatings were deposited via chemical vapor deposition on nuclear graphite substrates with controlled roughness (Ra = 6.2, 1.0, and 0.4 μm), and the effects of roughness on microstructure and adhesion were systematically evaluated. A nonlinear dependence of coating performance on surface roughness was identified. Moderate roughness (Ra = 1.0 μm) yielded dense and well-crystallized coatings with smaller and more uniform grain aggregates (~9.45 μm) and minimal interfacial defects, resulting in the highest adhesion strength (Lc₁ = 62.2 N) and superior thermal shock resistance. In contrast, excessive roughness induced irregular aggregates and infiltration-related defects, leading to premature interfacial failure, whereas overly smooth surfaces weakened mechanical interlocking and physical adsorption, thereby reducing adhesion strength. A coupled mechanism involving mechanical interlocking, chemical diffusion, and stress dispersion was elucidated, demonstrating that optimal roughness governs interfacial integrity. These findings provide critical guidance for substrate pretreatment of SiC coatings in nuclear applications.