Zhen-Huan Wang
Research Subjects
Research Interests
Zhen-Huan Wang has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Jae-Min Cha
Department of Mechanical Engineering, Sunmoon University,70 sunmoon-ro 221 beon-gil, Tangjeong-myeon, Asan-si, Chungcheongnam-do 31460, Korea
1 shared publication - Jun Son
Department of Mechanical Engineering, Sunmoon University, 221-70 Sunmoon-ro, Tangjeong-myeon, Asan-si, Chungcheongnam-do 31460, Korea
1 shared publication - Sang-Jae Lee
Department of Mechanical Engineering, Sunmoon University,70 sunmoon-ro 221 beon-gil, Tangjeong-myeon, Asan-si, Chungcheongnam-do 31460, Korea
1 shared publication - Sun-Joon Byun
SFR NSSS System Design Division, Korea Atomic Energy Research Institute, 111 Daedeok-daero 989 Beon-gil, Yuseong-gu, Daejeon 34057, Korea
1 shared publication
Latest Publications
- Open Access
- 5 January 2017
- Published by MDPI AG in Preprints.org
Experimental Study on the Heat Transfer Characteristics of the Enhanced Fin-Tube Heat Exchanger Applied a Coiled Turbulator
This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.
- 5 January 2017
- Published by MDPI AG in Preprints.org
Open AccessExperimental Study on the Heat Transfer Characteristics of the Enhanced Fin-Tube Heat Exchanger Applied a Coiled Turbulator
This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.