ANAndrew R. Neureuther

Andrew R. Neureuther

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Andrew R. Neureuther has a total of 17 co-authors. Here are the top co-authors by number of shared publications:

  • Patrick P. Naulleau

    Center for X-Ray Optics, Lawrence Berkeley National Lab, Berkeley, California

    4 shared publications
  • Gregory R. McIntyre

    University of California–Berkeley, Electronic Engineering and Computer Science Department, Berkeley, California 94720 and Advanced Micro Devices, 1 AMD Place, Sunnyvale, California 94088-3453

    2 shared publications
  • Patrick Naulleau

    Center for X-ray Optics, Lawrence Berkeley National Laboratory, Berkeley, California

    2 shared publications
  • Stuart Sherwin

    EUV Tech, Martinez, California, United States

    2 shared publications
  • Yow-Gwo Wang

    University of California, Berkeley, Department of Electrical Engineering and Computer Sciences, Berkeley, California, United StatesbCenter for X-ray Optics, Lawrence Berkeley National Laboratory, Berkeley, California, United States

    2 shared publications
  • Chris H. Clifford

    Mentor Graphics (United States)

    1 shared publication

Latest Publications

  • Picometer sensitivity metrology for EUV absorber phase

    by Stuart Sherwin, Isvar A. Cordova, Ryan H. Miyakawa, Markus P. Benk, Laura Waller, Andrew R. Neureuther, Patrick Naulleau

    With growing interest in EUV attenuated phase-shift masks due to their superior image quality for applications such as dense contact and pillar arrays, it is becoming critical to model, measure, and monitor the intensity and relative phase of multilayer and absorber reflections. We present a solution based on physical modeling of reflectometry data, which can achieve single picometer phase precision and sensitivity to changes in average film thickness below one atomic monolayer. We measure absorber and multilayer reflectivity to determine thin-film parameters with a multidimensional optimization and then acquire a new measurement of either multilayer or absorber to determine perturbations in surface contamination thickness. While it is difficult to assess the accuracy of the first step, the simplicity of the second step allows us to characterize our sensitivity to changes in contamination thickness. We apply this analysis using an initial set of measurements and repeated measurements after a period of storage. For the multilayer, the total contamination growth was 1068 pm, which occurred almost exclusively during storage (1085 pm) and decreased very slightly during repeated measurements (−17 pm). For the absorber, the behavior was quite different, with a total growth of 126 pm, which occurred much less during storage (28 pm) and primarily during repeated measurements (98 pm). Ultimately, the change in relative phase (absorber minus multilayer) was −0.86 deg for the multilayer and −1.12 deg for the absorber. We estimate the precision of the surface contamination measurement to be 3σ < 6 pm for measuring thickness and 3σ < 0.2 deg for measuring phase.

  • Open Access

    Three-dimensional modeling of EUV photoresist using the multivariate Poisson propagation model

    by Luke T. Long, Andrew R. Neureuther, Patrick P. Naulleau

    Background: As target feature sizes for EUV lithography shrink, it is becoming ever more important to understand the intricate details of photoresist materials, including the role of the “third dimension”—the dimension perpendicular to the wafer. With resist thicknesses shrinking toward the single-digit nanometer scale alongside target linewidths, small changes in resist performance in this dimension will have a greater overall effect on pattern quality. Aim: To use modeling to understand the effect that the third dimension has on resist performance, in particular the interplay between the third dimension and resist stochastics. Approach: We developed a three-dimensional version of the multivariate Poisson propagation model, a stochastic resist simulator. As a test case for the model, we explore the role of acid diffusion in the so-called third dimension by simulating 105 vias at a series of z-blur conditions. Results: Our model suggests that increased z-blur yields an improvement in both dose to size and pattern uniformity without sacrificing resolution. Conclusions: We have developed a 3D resist model that can simulate large numbers of contacts. Early results from the 3D model show improved patterning performance can be achieved by increasing the z-blur.


  • Open Access

    Investigating extreme ultraviolet radiation chemistry with first-principles quantum chemistry calculations

    by Jonathan H. Ma, Han Wang, David G. Prendergast, Andrew R. Neureuther, Patrick P. Naulleau

    In extreme ultraviolet (EUV) lithography, chemistry is driven by secondary electrons. A deeper understanding of these processes is needed. However, electron-driven processes are inherently difficult to experimentally characterize for EUV materials, impeding targeted material engineering. A computational framework is needed to provide information for rational material engineering and identification at a molecular level. We demonstrate that density functional theory calculations can fulfill this purpose. We first demonstrate that primary electron energy spectrum can be predicted accurately. Second, the dynamics of a photoacid generator upon excitation or electron attachment are studied with ab-initio molecular dynamics calculations. Third, we demonstrate that electron attachment affinity is a good predictor of reduction potential and dose to clear. The correlation between such calculations and experiments suggests that these methods can be applied to computationally screen and design molecular components of EUV material and speed up the development process.


  • Modeling high-efficiency extreme ultraviolet etched multilayer phase-shift masks

    by Stuart Sherwin, Andrew Neureuther, Patrick Naulleau

    Achieving high-throughput extreme ultraviolet (EUV) patterning remains a major challenge due to low source power; phase-shift masks can help solve this challenge for dense features near the resolution limit by creating brighter images than traditional absorber masks when illuminated with the same source power. We explore applications of etched multilayer phase-shift masks for EUV lithography, both in the current-generation 0.33 NA and next-generation 0.55 NA systems. We derive analytic formulas for the thin-mask throughput gains, which are 2.42× for lines and spaces and 5.86× for contacts compared with an absorber mask with dipole and quadrupole illumination, respectively. Using rigorous finite-difference time-domain simulations, we quantify variations in these gains by pitch and orientation, finding 87% to 113% of the thin-mask value for lines and spaces and a 91% to 99% for contacts. We introduce an edge placement error metric, which accounts for CD errors, relative feature motion, and telecentricity errors, and use this metric both to optimize mask designs for individual features and to explore which features can be printed on the same mask. Furthermore, we find that although partial coherence shrinks the process window, at an achievable sigma of 0.2 we obtain a depth of focus of 340 nm and an exposure latitude of 39.2%, suggesting that partial coherence will not limit the feasibility of this technology. Finally, we show that many problems such as sensitivity to etch uniformity can be greatly mitigated using a central obscuration in the imaging pupil.


  • Impact of tool design on defect detection sensitivity in extreme ultraviolet actinic blank inspection

    by Yow-Gwo Wang, Andrew R. Neureuther, Patrick P. Naulleau

    We discuss the impact of various tool design perspectives on defect detection sensitivity for dark-field-based extreme ultraviolet (EUV) actinic blank inspection. We consider the impact of pixel size, EUV source type, and photon collection efficiency on critical defect signal-to-noise ratio (SNR) performance. The results show that as the pixel size approaches the target defect image size, defect SNR increases, and that pixel size also determines the dominant noise source in the inspection system. Moreover, the choice of the EUV source affects the optimal numerical aperture (NA) and illumination settings. For plasma-discharged sources, more photons provided by larger partial coherent illumination can improve the defect SNR, while coherent illumination is needed to get a higher defect SNR for synchrotron-based source. In the end, we show that simply increasing the photon collection efficiency by using high-NA optics or increasing the source power cannot always improve the defect SNR. In a speckle-noise dominated situation, larger outer NA includes more noise than defect signal, thus resulting in a lower SNR. The impact of source power also saturates at a certain level as the system becomes speckle-noise limited compared to photon-noise limited.


  • Impact of noise sources and optical design on defect detection sensitivity in extreme ultraviolet actinic pattern inspection tool

    by Yow-Gwo Wang, Andrew R. Neureuther, Patrick P. Naulleau

    We discuss the impact of various noise sources and the optical design in bright field extreme ultraviolet (EUV) actinic inspection of mask features for defects in the patterned absorber. It is shown that an optimum pixel size is needed to maximize the defect signal-to-noise ratio (SNR) to balance the trade-off in increasing signal strength with shot noise from defect signal and the background pattern intensity (mask layout image) and speckle noise from the mask blank roughness. Moreover, we consider defocus showing that the EUV mask phase effect has an asymmetric impact on pattern defect SNR’s through-focus behavior. The impact of defocus limits inspection performance based on defect SNR. Using critical defect sizes in a case study, we show the defect SNR performance of the limiting case and discuss the possibility of utilizing a nominal defocus in the inspection system to leverage the phase effect of EUV mask absorber to improve the defect SNR. A 50% improvement in defect SNR is shown to be possible by introducing a −50  nm nominal defocus into the bright field inspection system.


  • Fast simulation methods and modeling for extreme ultraviolet masks with buried defects

    by Chris H. Clifford, Andrew R. Neureuther

    To support the successful implementation of extreme ultraviolet (EUV) lithography for high volume manufacturing, a spectrum of simulation tools is needed. For investigation of new materials and geometries, rigorous but computationally expensive simulations are required. For faster simulations, a new method, rapid absorber defect interaction computation for advanced lithography (RADICAL), is introduced. RADICAL is a modular program, that uses separate methods to simulate the absorber pattern and defective multilayer. Two different methods are used to simulate the multilayer within RADICAL: ray tracing and single surface approximation (SSA). Ray tracing can accurately simulate arbitrary multilayer geometries. SSA is only accurate for defects shorter than 4.5nm on the multilayer surface. With ray tracing, RADICAL is nearly 1000 times faster than finite difference time domain (FDTD) for simulating line-space patterns over buried defects. RADICAL with SSA is nearly 25,000 times faster than FDTD. The accuracy of RADICAL is shown to be excellent for simulating defects in focus, and for simulating defects smaller than 2.5nm through focus. The error can be as high as 4nm in predicting CD change for larger defects out of focus due to the complexities of modeling the phase of buried defects. But this error is predictable and will likely be acceptable for most applications considering the huge speed advantages of RADICAL.


  • Polarization aberrations in hyper-numerical-aperture projection printing: a comparison of various representations

    by Jongwook Kye, Gregory R. McIntyre, Harry Levinson, Andrew R. Neureuther

    Various representations of polarization aberrations are described and compared for optical lithography. Polarization aberrations, which are potentially important with hyper-numerical-aperture tools, are a complicated phenomena that refer to induced polarization-dependent wavefront distortions as light propagates through an imaging system. Pupil representations based on the following concepts are discussed: the physical polarization properties, the Mueller matrix, the Jones matrix, and the Jones matrix decomposed into a Pauli spin matrix basis. Although each has its own advantages and disadvantages, it is concluded that the Jones matrix representation decomposed into a Pauli spin matrix basis offers the most useful format for the lithographer due to its compact notation, physically intuitive interpretation, ability to be implemented into standard imaging equations, and its usefulness as an input into a lithographic simulator. Depending on the assumptions that can be made, the pupil specification consists of three to eight independent functions, where a normalization constant is calculated to ensure a physically realizable pupil. An example is shown to illustrate the usefulness of this strategy. Additionally, a simple metric for lens polarization quality based on this representation is proposed.


  • Phase-shifting mask polarimetry: monitoring polarization at 193-nm high numerical aperture and immersion lithography with phase shifting masks

    by Andrew R. Neureuther, Gregory R. McIntyre

    A technique using phase-shifting test mask patterns is introduced for monitoring polarization balance of the illumination in high numerical aperture (NA) and immersion projection printing systems. Test mask patterns are derived from high NA proximity effects and serve to scatter light into high angle spatial frequencies. This creates a central intensity dependent only on the local state of polarization. A test mask consisting of multiple patterns is proposed to monitor the polarization from any arbitrary illumination scheme. Proper calibration of the test reticle enables reasonable mask-making limitations and mask topography effects to be tolerated. A set of linear equations enable determination of the Stokes parameters from a series of resist images. Practical examples are simulated with rigorous electromagnetic theory. In resist, this technique is likely to monitor polarization with a sensitivity of more than 1.5% of the clear field per percent change in polarization state for on-axis illumination, or more than 0.75% for off-axis illumination. The effects of various realistic imaging conditions are discussed.


  • Domain decomposition methods for the rapid electromagnetic simulation of photomask scattering

    by Konstantinos Adam, Andrew R. Neureuther

    An integrated methodology has been developed for computer simulation of electromagnetic scattering from large, nonperiodic, two-dimensional layouts of advanced photomasks (masks with optical proximity correction and phase-shifting masks). The domain decomposition method consists of three steps: First, by virtue of the linearity of the Kirchhoff–Fresnel diffraction integral, the mask layout is decomposed into a set of constituent single-opening masks. Second, the rigorous electromagnetic simulation of each three-dimensional structure from the set of these single-opening masks is circumvented and, instead, the result for the scattered field is synthesized based on two two-dimensional rigorous electromagnetic simulations that model the mask geometry in two cross-sectional planes. Subsequently, compact equivalent source models are used to describe the scattered fields on a reference plane. These models are constructed in such a way as to minimize the error in the part of the diffraction spectrum that passes through the projection system, allowing accurate and efficient image simulation. The normalized mean square error of the near scattered field is typically a fraction of 1% and speed-up factors for the total simulation time in excess of 400 (compared with the rigorous mask model) are achieved. The use of a look-up table approach facilitates orders of magnitude of further speed improvement. © 2002 Society of Photo-Optical Instrumentation Engineers.