Ilya V. Tretyakov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ilya V. Tretyakov has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Alexander G. Khina
Department of Chemistry, M. V. Lomonosov Moscow State University, Moscow 119991, Russia
1 shared publication - Denis P. Bulkatov
NTI Center “Digital Materials Science: New Materials and Substances”, Bauman Moscow State Technical University, Moscow 105005, Russia
1 shared publication - Elizaveta N. Abramova
Special Mechanical Engineering Faculty, Bauman Moscow State Technical University, Moscow 105005, Russia
1 shared publication - Ivan P. Storozhuk
NTI Center “Digital Materials Science: New Materials and Substances”, Bauman Moscow State Technical University, Moscow 105005, Russia
1 shared publication - Nikolay S. Malyshev
Russian Academy of Sciences
1 shared publication - Semen Yu. Fedorov
NTI Center “Digital Materials Science: New Materials and Substances”, Bauman Moscow State Technical University, Moscow 105005, Russia
1 shared publication
Latest Publications
- Open Access
Lunar Regolith Simulant–Filled High-Performance Thermoplastic Composites for Lunar Construction and Their Potential for Additive Manufacturing
The use of lunar regolith (LR) for lunar construction is a key route to reducing the mass of materials transported from Earth. In this work, highly filled composites based on polyphenylsulfone (PPSU) with Tg = 219.1 °C and modified polyetherimide (PEI) with Tg = 247.1 °C containing up to 92.5 wt.% of LR simulant were prepared by dry blending the LR simulant and the polymer powders, followed by hot pressing. Their internal structure, mechanical, thermal, thermomechanical, and melt/flow properties were evaluated. The properties of the composites strongly depended on the LR simulant content and were governed by two competing mechanisms: restriction of polymer-chain mobility and of matrix deformation by the rigid mineral filler at moderate LR simulant contents, and increased porosity and loss of matrix continuity caused by binder deficiency at excessive filler loadings. At LR simulant contents of up to 60 wt.% for PPSU and 85 wt.% for PEI, dense, low-porosity (−6 K−1 and 10.1 × 10−6 K−1 for PPSU- and PEI-based composites, respectively. Composites containing 50–60 wt.% of LR simulant retained melt/flow capability, indicating their potential suitability for processing by melt extrusion and additive manufacturing. Based on the obtained data, recommendations were formulated for application of the developed composites in melt-based 3D printing of complex-geometry parts and hot-pressed simple-shape construction elements.
Open AccessLunar Regolith Simulant–Filled High-Performance Thermoplastic Composites for Lunar Construction and Their Potential for Additive Manufacturing
The use of lunar regolith (LR) for lunar construction is a key route to reducing the mass of materials transported from Earth. In this work, highly filled composites based on polyphenylsulfone (PPSU) with Tg = 219.1 °C and modified polyetherimide (PEI) with Tg = 247.1 °C containing up to 92.5 wt.% of LR simulant were prepared by dry blending the LR simulant and the polymer powders, followed by hot pressing. Their internal structure, mechanical, thermal, thermomechanical, and melt/flow properties were evaluated. The properties of the composites strongly depended on the LR simulant content and were governed by two competing mechanisms: restriction of polymer-chain mobility and of matrix deformation by the rigid mineral filler at moderate LR simulant contents, and increased porosity and loss of matrix continuity caused by binder deficiency at excessive filler loadings. At LR simulant contents of up to 60 wt.% for PPSU and 85 wt.% for PEI, dense, low-porosity (−6 K−1 and 10.1 × 10−6 K−1 for PPSU- and PEI-based composites, respectively. Composites containing 50–60 wt.% of LR simulant retained melt/flow capability, indicating their potential suitability for processing by melt extrusion and additive manufacturing. Based on the obtained data, recommendations were formulated for application of the developed composites in melt-based 3D printing of complex-geometry parts and hot-pressed simple-shape construction elements.