RBRoman A. Bykov

Roman A. Bykov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Roman A. Bykov has a total of 4 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Structure and Properties of Multicomponent Arc-PVD Ti–Cr–Mo–Ni–N Coatings Deposited on HG20, HS123 and HV420 Carbide Alloys and C80W1 Tool Steel

    by Dmitry S. Belov, Igor V. Blinkov, Alexander P. Demirov, Alexey V. Chernogor, Roman A. Bykov

    Although the arc-PVD Ti–Cr–Mo–Ni–N coatings deposited on HG20, HS123 and HV420 carbide alloys and C80W1 tool steel have approximately similar elemental and phase compositions, they differ in morphology, macrostructure, and macrostress level. The coating deposited on steel exhibits macrolayering, a wider coating–substrate transition zone and tensile structural macrostresses. In contrast, coatings deposited on carbide alloys develop compressive structural macrostresses. This behavior can be explained by the overheating during deposition caused by ion bombardment. Overheating is more pronounced for a coating on steel because the thermal diffusivity of steel is lower than that of hard alloys. The Ti–Cr–Mo–Ni–N coating on C80W1 steel exhibited a lower hardness (approximately 20.3 GPa) than the coatings on the carbide alloys (21.7–25.1 GPa). It also showed lower resistance to cohesive failure, with Lc3 ≈ 30 N, compared with ≈94 N for the coatings on the carbide alloys. Here, Lc3 denotes the critical load for cohesive cracking of the coating induced by plastic extrusion of the substrate material. The coating on steel also exhibited a higher specific wear rate at 20 °C and 500 °C. Its K20 and K500 values were 49.80 and 74.20, respectively. The corresponding values were 4.19 and 11.99 for HG20, 2.91 and 12.35 for HS123, and 6.33 and 14.71 for HV420, respectively, expressed in units of 10−6 mm3·N−1·m−1.

  • Open Access

    Structure and Properties of Multicomponent Arc-PVD Ti–Cr–Mo–Ni–N Coatings on Carbide Alloys HG20, HS123, HV420 and Tool Steel C80W1

    by Dmitry S. Belov, Igor V. Blinkov, Alexander P. Demirov, Alexey V. Chernogor, Roman A. Bykov

    The arc-PVD Ti–Cr–Mo–Ni–N coatings on HG20, HS123, HV420 carbide alloys and C80W1 tool steel, while having approximately the same elemental and phase compositions, differ in morphology, macrostructure, and level of macrostresses. When deposited on steel, the coating exhibits macrolayering, a more extended coating–substrate transition zone, and develops tensile macrostresses, in contrast to the coatings on carbide alloys, which develop compressive macrostresses. The behaviour can be explained by the overheating of the coating during deposition, which results from ion bombardment and is more pronounced on steel due to its poorer thermal diffusivity relative to carbide alloys. The CLTE difference between steel and the coating is significantly larger than that between the carbides and the coating, further contributing to the effect. It was found that, considering these features, the Ti–Cr–Mo–Ni–N coating on steel exhibits lower hardness (~20.3GPa), lower adhesion strength to the substrate (Lc3≈30N, the indenter load at scratch testing corresponding to the onset of coating wear), and a higher wear intensity at room temperature and 500°C (49.80 and 74.20·10−6 mm3·N−1·m−1, respectively), as compared with the hardness values of 25.1–21.7GPa, Lc3≈100N, and wear intensity (corresponding to the absence of a visible wear crater) for the Ti–Cr–Mo–Ni–N coatings on the aforementioned carbide alloys.