Yuxuan Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuxuan Sun has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Mujun Li
Institute of Humanoid Robots Department of Precision Machinery and Precision Instrumentation University of Science and Technology of China Hefei China
2 shared publications Boxi Sun
Institute of Humanoid Robots Department of Precision Machinery and Precision Instrumentation University of Science and Technology of China Hefei China
1 shared publicationHao Jing
Institute of Humanoid Robots Department of Precision Machinery and Precision Instrumentation University of Science and Technology of China Hefei China
1 shared publication- Hao Zhou
University of Science and Technology of China, Hefei, China
1 shared publication Hongbin Zang
School of Manufacturing Science and Engineering Southwest University of Science and Technology Mianyang China
1 shared publication- Shiwu Zhang
University of Science and Technology of China
1 shared publication
Latest Publications
- 14 November 2026
- Published by Wiley in Advanced Materials
Dynamic Spatial Programming of Active–Active Antagonistic Fiber Architectures for Enhanced Morphing
Programming multiple deformation modes within a continuous liquid crystal elastomer (LCE) filament remains challenging because molecular alignment and active‐material distribution are typically coupled to the external printing path. Here, a rotational multimaterial printing strategy is introduced that encodes two co‐curable LCE phases with opposite free thermal strains within individual fibers. These antagonistic free strains act cooperatively after co‐curing to generate internal strain mismatch and structural deformation. A dual‐channel rotating nozzle co‐extrudes a thermally contracting nematic LCE and a thermally elongating smectic LCE, while nozzle angle, angular velocity, and flow‐rate ratio prescribe their cross‐sectional and axial distributions. Discrete and continuous rotation enable contraction, elongation, in‐plane bending, out‐of‐plane curling, and helical coiling without changing the filament centerline. Under matched conditions, the active–active fibers exhibit an approximately 1.6‐fold increase in curvature relative to the active–passive controls, while simultaneous co‐curing increases interfacial peel strength by approximately 30 times that achieved by sequential curing. The same encoding strategy extends from individual fibers to grids and Gaussian‐curvature surfaces and enables force‐generating strips, thermal protection, self‐sensing, particle sorting, and adaptive gripping. Rotational multimaterial printing therefore decouples intra‐filament architecture from toolpath geometry and provides a general route to spatially programmable active fibers.
- 14 November 2026
- Published by Wiley in Advanced Materials
Dynamic Spatial Programming of Active–Active Antagonistic Fiber Architectures for Enhanced Morphing
Programming multiple deformation modes within a continuous liquid crystal elastomer (LCE) filament remains challenging because molecular alignment and active‐material distribution are typically coupled to the external printing path. Here, a rotational multimaterial printing strategy is introduced that encodes two co‐curable LCE phases with opposite free thermal strains within individual fibers. These antagonistic free strains act cooperatively after co‐curing to generate internal strain mismatch and structural deformation. A dual‐channel rotating nozzle co‐extrudes a thermally contracting nematic LCE and a thermally elongating smectic LCE, while nozzle angle, angular velocity, and flow‐rate ratio prescribe their cross‐sectional and axial distributions. Discrete and continuous rotation enable contraction, elongation, in‐plane bending, out‐of‐plane curling, and helical coiling without changing the filament centerline. Under matched conditions, the active–active fibers exhibit an approximately 1.6‐fold increase in curvature relative to the active–passive controls, while simultaneous co‐curing increases interfacial peel strength by approximately 30 times that achieved by sequential curing. The same encoding strategy extends from individual fibers to grids and Gaussian‐curvature surfaces and enables force‐generating strips, thermal protection, self‐sensing, particle sorting, and adaptive gripping. Rotational multimaterial printing therefore decouples intra‐filament architecture from toolpath geometry and provides a general route to spatially programmable active fibers.
- Open Access
- 26 October 2026
- Published by Association for Computing Machinery (ACM)
- p. 853-866
Shape-Reconfigurable Charger: Magnetic Power Pathway Programming via Computed Morphing
- 26 October 2026
- Published by Association for Computing Machinery (ACM)
- p. 853-866
Open AccessShape-Reconfigurable Charger: Magnetic Power Pathway Programming via Computed Morphing