SRSasono Rahardjo
Sasono Rahardjo
*This is an algorithmically generated author record based on publicly available information.
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sasono Rahardjo has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Retno Wigajatri Purnamaningsih
Universitas Indonesia
1 shared publication - Reza Diharja
OptoElectronics Laboratory, Department of Electrical Engineering, Faculty of Engineering, Universitas Indonesia, Depok 16424, West Java, Indonesia
1 shared publication
Latest Publications
- Open Access
A Statistical Framework for Nonlinear Calibration of a Single FBG Sensor Under Coupled Pressure–Temperature Loading
Fiber Bragg Grating (FBG) sensors are widely used to measure pressure and temperature. However, when both are subjected to a coupled environment, the Bragg wavelengths influence each other, causing biased measurements if not properly calibrated. Most calibration models assume linear sensitivity, which may not hold across the entire operating range. This study proposes a five-step statistical calibration framework for a single FBG sensor under coupled pressure–temperature conditions: data preparation; fitting linear, quadratic, and cubic models; model selection using AIC/BIC; local sensitivity calculation; and contribution decomposition via Response Surface Methodology (RSM). The framework was tested on experimental data from an FBG sensor mounted on a metal membrane, at pressures of 0 MPa–2.0 MPa and temperatures of 5 °C–45 °C. Nonlinear models outperformed linear ones, with values of 0.9725–0.9992. The model was validated using Leave-One-Out Cross-Validation (LOOCV), yielding an out-of-sample RMSE (Root Mean Square Error) of 0.0452 nm. Pressure sensitivity remained constant at 0.2250 nm/MPa, while temperature sensitivity decreased from 0.0224 nm/°C at 5 °C to 0.0069 nm/°C at 45 °C. RSM showed that pressure influences the slope and temperature influences the offset, with no significant interaction. Residual analysis satisfied the regression assumptions, and the combined uncertainty (0.008 nm/MPa; 0.0003 nm/°C) was much smaller than the observed sensitivity range, confirming that the variations are physical, not instrument noise. This framework is practical and statistically sound for single FBG sensor calibration.Open AccessA Statistical Framework for Nonlinear Calibration of a Single FBG Sensor Under Coupled Pressure–Temperature Loading
Fiber Bragg Grating (FBG) sensors are widely used to measure pressure and temperature. However, when both are subjected to a coupled environment, the Bragg wavelengths influence each other, causing biased measurements if not properly calibrated. Most calibration models assume linear sensitivity, which may not hold across the entire operating range. This study proposes a five-step statistical calibration framework for a single FBG sensor under coupled pressure–temperature conditions: data preparation; fitting linear, quadratic, and cubic models; model selection using AIC/BIC; local sensitivity calculation; and contribution decomposition via Response Surface Methodology (RSM). The framework was tested on experimental data from an FBG sensor mounted on a metal membrane, at pressures of 0 MPa–2.0 MPa and temperatures of 5 °C–45 °C. Nonlinear models outperformed linear ones, with values of 0.9725–0.9992. The model was validated using Leave-One-Out Cross-Validation (LOOCV), yielding an out-of-sample RMSE (Root Mean Square Error) of 0.0452 nm. Pressure sensitivity remained constant at 0.2250 nm/MPa, while temperature sensitivity decreased from 0.0224 nm/°C at 5 °C to 0.0069 nm/°C at 45 °C. RSM showed that pressure influences the slope and temperature influences the offset, with no significant interaction. Residual analysis satisfied the regression assumptions, and the combined uncertainty (0.008 nm/MPa; 0.0003 nm/°C) was much smaller than the observed sensitivity range, confirming that the variations are physical, not instrument noise. This framework is practical and statistically sound for single FBG sensor calibration.