Emmanuel Okechukwu Achukwu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Emmanuel Okechukwu Achukwu has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Macaulay Mfon Owen
Universiti Malaya UM
12 shared publications - Hazizan Md Akil
School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia (USM), Nibong Tebal, Malaysia
8 shared publications - Ahmad Zafir Romli
Universiti Teknologi MARA (UiTM)
6 shared publications - Solehuddin Shuib
Universiti Teknologi MARA
6 shared publications - Umaru S. Ishiaku
Polymer and Textile Engineering Faculty of Engineering, Ahmadu Bello University Zaria Nigeria
3 shared publications - Abdullahi Danladi
Department of Polymer and Textile Engineering, Ahmadu Bello University, Zaria, Nigeria
2 shared publications
Latest Publications
- 26 July 2026
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
Recycled polyolefin-based thermoplastic waste reinforced with recycled nylon fibre for sustainable prosthetic socket materials: Mechanical, thermal, microstructural, and finite element evaluation
This study evaluates recycled polyolefin-based thermoplastic waste reinforced with recycled nylon fiber as a sustainable candidate material for prosthetic socket applications. Recycled polyolefin-based thermoplastic waste (PW), recycled nylon fiber waste (NHFW), and PW/NHFW composites were fabricated through melt compounding and compression moulding, followed by mechanical, thermal, microstructural, statistical, and finite element analyses. Relative to PW, which exhibited a tensile modulus of 245.74 MPa, tensile strength of 37.57 MPa, flexural modulus of 422.09 MPa, and flexural strength of 36.89 MPa, the PW/NHFW composite achieved 311.61 MPa, 38.55 MPa, 571.98 MPa, and 50.75 MPa, respectively, corresponding to improvements of 26.8%, 2.6%, 35.5%, and 37.5%. One-way ANOVA confirmed that material composition significantly affected tensile strength (F = 156.26, p = 2.56E-09) and flexural strength (F = 530.95, p = 1.95E-12). Tukey HSD analysis further showed that NHFW had significantly higher tensile strength than both PW and PW/NHFW, whereas PW/NHFW was not significantly different from PW in tensile strength (mean difference = 0.98 MPa; p = .315). In contrast, all flexural pairwise comparisons were significant, including the improvement of PW/NHFW over PW (mean difference = 13.86 MPa; q = 13.91), indicating that nylon fiber reinforcement was expressed more strongly under bending than under uniaxial tension. Impact and hardness testing showed that PW/NHFW achieved an impact strength of 7.08 kJ/m 2 and hardness of 14.48 HRM. Thermal analysis confirmed adequate processing stability, while microscopy revealed fiber embedment, fiber bridging, and dispersed nylon reinforcement, with local pull-out and debonding indicating interfacial limitations. Finite element predictions reproduced the experimental tensile and flexural trends and showed improved stress redistribution in PW/NHFW. Overall, the findings demonstrate that recycled polyolefin-based thermoplastic/nylon fiber composites offer a promising material-level platform for sustainable prosthetic socket development.
- 26 July 2026
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
Recycled polyolefin-based thermoplastic waste reinforced with recycled nylon fibre for sustainable prosthetic socket materials: Mechanical, thermal, microstructural, and finite element evaluation
This study evaluates recycled polyolefin-based thermoplastic waste reinforced with recycled nylon fiber as a sustainable candidate material for prosthetic socket applications. Recycled polyolefin-based thermoplastic waste (PW), recycled nylon fiber waste (NHFW), and PW/NHFW composites were fabricated through melt compounding and compression moulding, followed by mechanical, thermal, microstructural, statistical, and finite element analyses. Relative to PW, which exhibited a tensile modulus of 245.74 MPa, tensile strength of 37.57 MPa, flexural modulus of 422.09 MPa, and flexural strength of 36.89 MPa, the PW/NHFW composite achieved 311.61 MPa, 38.55 MPa, 571.98 MPa, and 50.75 MPa, respectively, corresponding to improvements of 26.8%, 2.6%, 35.5%, and 37.5%. One-way ANOVA confirmed that material composition significantly affected tensile strength (F = 156.26, p = 2.56E-09) and flexural strength (F = 530.95, p = 1.95E-12). Tukey HSD analysis further showed that NHFW had significantly higher tensile strength than both PW and PW/NHFW, whereas PW/NHFW was not significantly different from PW in tensile strength (mean difference = 0.98 MPa; p = .315). In contrast, all flexural pairwise comparisons were significant, including the improvement of PW/NHFW over PW (mean difference = 13.86 MPa; q = 13.91), indicating that nylon fiber reinforcement was expressed more strongly under bending than under uniaxial tension. Impact and hardness testing showed that PW/NHFW achieved an impact strength of 7.08 kJ/m 2 and hardness of 14.48 HRM. Thermal analysis confirmed adequate processing stability, while microscopy revealed fiber embedment, fiber bridging, and dispersed nylon reinforcement, with local pull-out and debonding indicating interfacial limitations. Finite element predictions reproduced the experimental tensile and flexural trends and showed improved stress redistribution in PW/NHFW. Overall, the findings demonstrate that recycled polyolefin-based thermoplastic/nylon fiber composites offer a promising material-level platform for sustainable prosthetic socket development.
- Open Access
- 16 July 2026
- Published by Elsevier in Composites Part C: Open Access
- Vol. 20
Vacuum-infused woven jute/glass hybrid epoxy laminates: Effects of ply architecture on thermo-mechanical performance and finite element analysis
- 16 July 2026
- Published by Elsevier in Composites Part C: Open Access
- Vol. 20
Open AccessVacuum-infused woven jute/glass hybrid epoxy laminates: Effects of ply architecture on thermo-mechanical performance and finite element analysis
- Open Access
- 2 April 2026
- Published by Elsevier in SSRN Electronic Journal
Vacuum-Infused Woven Jute/Glass Hybrid Epoxy Laminates: Effects of Ply Architecture on Thermo-Mechanical Performance and Finite Element Analysis
Natural fibre composites offer sustainability advantages but often suffer from limited structural reliability and thermal stability when used as single-fibre systems. In this study, vacuum-infused woven jute/epoxy and jute/glass hybrid epoxy laminates with 2-, 4-, and 6-ply architectures were fabricated and systematically evaluated to determine the combined effects of fibre hybridisation and ply architecture on thermo-mechanical performance. Tensile, flexural, impact, density, and thermogravimetric analyses were performed, while scanning electron microscopy and optical microscopy were used to examine fracture features and laminate morphology. Finite element analysis (FEA) was conducted to simulate stress distribution and deformation behaviour, and analysis of variance (two-way ANOVA) was used to determine the statistical significance of hybridisation and ply architecture. The results demonstrate that hybrid laminates significantly outperformed jute-only systems, with the 6-ply jute/glass configuration achieving tensile strength and modulus improvements of 22.6% and 283%, respectively, together with flexural strength and modulus enhancements of approximately 50% and 75%. Thermal analysis revealed delayed degradation onset and approximately fourfold higher residual char yield, confirming improved thermal resistance of the hybrid architectures, while microscopy revealed reduced fibre pull-out, improved fibre embedding, and more compact laminate structures. FEA predictions reproduced experimental mechanical responses with deviations between 2 – 14% and accurately captured stress localisation patterns consistent with observed failure modes, validating the numerical modelling framework. Overall, the results indicate that controlled hybridisation and ply architecture provide an effective route for improving the structural efficiency of vacuum-infused natural fibre composite laminates for lightweight engineering applications.
- 2 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessVacuum-Infused Woven Jute/Glass Hybrid Epoxy Laminates: Effects of Ply Architecture on Thermo-Mechanical Performance and Finite Element Analysis
Natural fibre composites offer sustainability advantages but often suffer from limited structural reliability and thermal stability when used as single-fibre systems. In this study, vacuum-infused woven jute/epoxy and jute/glass hybrid epoxy laminates with 2-, 4-, and 6-ply architectures were fabricated and systematically evaluated to determine the combined effects of fibre hybridisation and ply architecture on thermo-mechanical performance. Tensile, flexural, impact, density, and thermogravimetric analyses were performed, while scanning electron microscopy and optical microscopy were used to examine fracture features and laminate morphology. Finite element analysis (FEA) was conducted to simulate stress distribution and deformation behaviour, and analysis of variance (two-way ANOVA) was used to determine the statistical significance of hybridisation and ply architecture. The results demonstrate that hybrid laminates significantly outperformed jute-only systems, with the 6-ply jute/glass configuration achieving tensile strength and modulus improvements of 22.6% and 283%, respectively, together with flexural strength and modulus enhancements of approximately 50% and 75%. Thermal analysis revealed delayed degradation onset and approximately fourfold higher residual char yield, confirming improved thermal resistance of the hybrid architectures, while microscopy revealed reduced fibre pull-out, improved fibre embedding, and more compact laminate structures. FEA predictions reproduced experimental mechanical responses with deviations between 2 – 14% and accurately captured stress localisation patterns consistent with observed failure modes, validating the numerical modelling framework. Overall, the results indicate that controlled hybridisation and ply architecture provide an effective route for improving the structural efficiency of vacuum-infused natural fibre composite laminates for lightweight engineering applications.
- Open Access
- 1 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
Interfacial nano-engineering of MXene-integrated carbon fiber composites for safer type V hydrogen tanks
Optimizing fibre orientation and MXene content improves the structural integrity, hydrogen barrier, and thermal stability of Type V COPVs.
- 1 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
Open AccessInterfacial nano-engineering of MXene-integrated carbon fiber composites for safer type V hydrogen tanks
Optimizing fibre orientation and MXene content improves the structural integrity, hydrogen barrier, and thermal stability of Type V COPVs.
- Open Access
- 30 July 2024
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 54
Mechanical and thermal characterization of resin-infused cotton fabric/epoxy composites: Influence of woven construction parameters and surface treatments
This study explores the mechanical and thermal characterization of epoxy-based composites reinforced with chemically modified woven cotton fabrics using the resin infusion technique. The woven fabrics construction parameters were varied in terms of weft yarn counts (16, 20, and 24 Tex) and pick densities as defined by pick wheel teeth (PWT) (30, 36, and 41 T). The fabrics were surface treated with 6% concentration of sodium hydroxide (NaOH) using the alkali treatment method. The obtained results revealed that mechanical strength improved with decreasing weft yarn count and increasing PWT. Notably, chemically treated composites with the highest PWT exhibited superior strength compared to untreated counterparts, attributed to more compact microstructures, reduced fabric/fiber breakages, and enhanced interfacial bonding between the reinforced plain-woven cotton fabric and epoxy matrix. Thermogravimetric analysis (TGA) showed that all composites have higher thermal stability above 300°C, with untreated fabric composites exhibiting the highest resistance to degradation, whereas the treated composite quickly degraded at an onset temperature of 288.4°C due to the removal of the hemicellulose, decomposition of the cellulose, and lignin content. In conclusion, the study indicates that surface treatment and woven construction parameters such as weft yarn counts and pick wheel teeth, as well as the resin infusion technique, significantly influence the mechanical, microstructural, and thermal properties of resin-infused woven cotton reinforced composites for potential application in industrial and automotive sectors, offering lightweight, durable solutions for components such as construction and building panels, doors, and roof panels.
- 30 July 2024
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 54
Open AccessMechanical and thermal characterization of resin-infused cotton fabric/epoxy composites: Influence of woven construction parameters and surface treatments
This study explores the mechanical and thermal characterization of epoxy-based composites reinforced with chemically modified woven cotton fabrics using the resin infusion technique. The woven fabrics construction parameters were varied in terms of weft yarn counts (16, 20, and 24 Tex) and pick densities as defined by pick wheel teeth (PWT) (30, 36, and 41 T). The fabrics were surface treated with 6% concentration of sodium hydroxide (NaOH) using the alkali treatment method. The obtained results revealed that mechanical strength improved with decreasing weft yarn count and increasing PWT. Notably, chemically treated composites with the highest PWT exhibited superior strength compared to untreated counterparts, attributed to more compact microstructures, reduced fabric/fiber breakages, and enhanced interfacial bonding between the reinforced plain-woven cotton fabric and epoxy matrix. Thermogravimetric analysis (TGA) showed that all composites have higher thermal stability above 300°C, with untreated fabric composites exhibiting the highest resistance to degradation, whereas the treated composite quickly degraded at an onset temperature of 288.4°C due to the removal of the hemicellulose, decomposition of the cellulose, and lignin content. In conclusion, the study indicates that surface treatment and woven construction parameters such as weft yarn counts and pick wheel teeth, as well as the resin infusion technique, significantly influence the mechanical, microstructural, and thermal properties of resin-infused woven cotton reinforced composites for potential application in industrial and automotive sectors, offering lightweight, durable solutions for components such as construction and building panels, doors, and roof panels.
- 19 September 2023
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 115 (9) , 1606-1620
Mechanical and morphological characterizations of epoxy composites reinforced with surface modified woven cotton structures using vacuum bagging technique
- 19 September 2023
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 115 (9) , 1606-1620
Mechanical and morphological characterizations of epoxy composites reinforced with surface modified woven cotton structures using vacuum bagging technique
- 21 February 2023
- Published by Wiley in Polymer Composites
- Vol. 44 (4) , 2512-2529
Effects of high‐temperature optimization and resin coating treatment on the mechanical, thermal, and morphological properties of natural kenaf fiber‐filled engineering plastic composites
In this study, kenaf natural fibers were coated with acetone‐thinned epoxy resin before compounding with high‐temperature polyethylene terephthalate (PET). Thus, composites of sodium hydroxide treated and epoxy‐resin coated kenaf fibers (KF) reinforced PET (CTKF‐PET) were manufactured using extrusion and compression molding techniques at an optimized 10 wt% constant fiber loading and processing temperatures of 240, 250, and 260°C, and were characterized for mechanical, thermal, and morphological performances. The obtained results showed an optimum processing temperature of 240°C with maximum mechanical and thermal properties with good interfaces between the coated fillers and the matrix, compared to those obtained at 250 and 260°C. Thermogravimetric analysis recorded maximum onset degradation and decomposition temperatures of 338.9 and 381°C with 9.5% and 13% improvements respectively after resin coating which positively impacted the constituent coated composites compared to the uncoated KF. Differential scanning calorimetry glass transition (Tg) and melting temperatures (Tm) for the CKF‐PET composites was maximum at 119.0 and 262.8°C with 2.18% and 2.8% improvements respectively compared to uncoated composites. The overall properties of all coated kenaf‐reinforced PET (CKF‐PET) and coated‐treated (CTKF‐PET) composites were higher with improved morphological properties irrespective of the processing temperature compared to the raw kenaf (KF‐PET) composites. Hence, natural fibers can be treated with resin coating to improve the thermal stabilities of natural fiber engineering plastic composites, and the interfacial adhesion between the coated‐KF and the engineering plastic matrix. The resultant composites are suitable for high‐temperature engineering applications such as the automotive and construction industries.
- 21 February 2023
- Published by Wiley in Polymer Composites
- Vol. 44 (4) , 2512-2529
Effects of high‐temperature optimization and resin coating treatment on the mechanical, thermal, and morphological properties of natural kenaf fiber‐filled engineering plastic composites
In this study, kenaf natural fibers were coated with acetone‐thinned epoxy resin before compounding with high‐temperature polyethylene terephthalate (PET). Thus, composites of sodium hydroxide treated and epoxy‐resin coated kenaf fibers (KF) reinforced PET (CTKF‐PET) were manufactured using extrusion and compression molding techniques at an optimized 10 wt% constant fiber loading and processing temperatures of 240, 250, and 260°C, and were characterized for mechanical, thermal, and morphological performances. The obtained results showed an optimum processing temperature of 240°C with maximum mechanical and thermal properties with good interfaces between the coated fillers and the matrix, compared to those obtained at 250 and 260°C. Thermogravimetric analysis recorded maximum onset degradation and decomposition temperatures of 338.9 and 381°C with 9.5% and 13% improvements respectively after resin coating which positively impacted the constituent coated composites compared to the uncoated KF. Differential scanning calorimetry glass transition (Tg) and melting temperatures (Tm) for the CKF‐PET composites was maximum at 119.0 and 262.8°C with 2.18% and 2.8% improvements respectively compared to uncoated composites. The overall properties of all coated kenaf‐reinforced PET (CKF‐PET) and coated‐treated (CTKF‐PET) composites were higher with improved morphological properties irrespective of the processing temperature compared to the raw kenaf (KF‐PET) composites. Hence, natural fibers can be treated with resin coating to improve the thermal stabilities of natural fiber engineering plastic composites, and the interfacial adhesion between the coated‐KF and the engineering plastic matrix. The resultant composites are suitable for high‐temperature engineering applications such as the automotive and construction industries.
- 20 February 2023
- Published by Taylor & Francis in Composite Interfaces
- Vol. 30 (8) , 849-875
Recent advances on improving the mechanical and thermal properties of kenaf fibers/engineering thermoplastic composites using novel coating techniques: a review
Natural fiber-reinforced polymer composites are presently receiving the attention of scholars and industrialists due to their specific properties, such as being naturally eco-friendly, biodegradable, economical, viable, available, and sustainable. The key problems associated with natural fiber polymer composites, including fiber/matrix compatibility, high moisture absorption, and, especially, thermal degradation in engineering plastics (high-temperature plastics), constitute the most critical thrust of this review. It is noted that at high temperatures, natural fibers degrade and this has adversely restricted their usage with only commodity thermoplastics having relatively low melting temperatures, such as polypropylene (PP) and polyethylene (PE). This review paper, therefore, provides valuable research highlights on utilizing and improving the mechanical and thermal properties of natural kenaf fibers as reinforcement in engineering polymer composites for high-temperature engineering applications using polymer matrices, such as polyethylene terephthalate (PET), acrylonitrile butadiene styrene (ABS), and polyphenylene ether (PPE). The initial and various chemical treatments of natural fibers, their effect on the thermal and performance properties of natural fiber engineering thermoplastic composites, and the advanced treatment of epoxy coatings are reviewed. Applications of natural fiber-reinforced thermoplastic composites in the construction and automotive industries, as well as in other applications, are outlined. It was established that the adhesion and thermal stabilities between polymer matrix and natural fibers are better improved by surface coating with diluted epoxy resin thermoset. This eventually improved the overall thermal and performance properties of the resultant composites and will serve as a data bank and guide for manufacturers and future research directions using high-end engineering polymers with higher processing temperatures. GRAPHICAL ABSTRACT Surface coating treatment and composites production processes for improving the interface and mechanical and thermal properties of epoxy-coated natural (kenaf) fiber-filled engineering thermoplastics composites
- 20 February 2023
- Published by Taylor & Francis in Composite Interfaces
- Vol. 30 (8) , 849-875
Recent advances on improving the mechanical and thermal properties of kenaf fibers/engineering thermoplastic composites using novel coating techniques: a review
Natural fiber-reinforced polymer composites are presently receiving the attention of scholars and industrialists due to their specific properties, such as being naturally eco-friendly, biodegradable, economical, viable, available, and sustainable. The key problems associated with natural fiber polymer composites, including fiber/matrix compatibility, high moisture absorption, and, especially, thermal degradation in engineering plastics (high-temperature plastics), constitute the most critical thrust of this review. It is noted that at high temperatures, natural fibers degrade and this has adversely restricted their usage with only commodity thermoplastics having relatively low melting temperatures, such as polypropylene (PP) and polyethylene (PE). This review paper, therefore, provides valuable research highlights on utilizing and improving the mechanical and thermal properties of natural kenaf fibers as reinforcement in engineering polymer composites for high-temperature engineering applications using polymer matrices, such as polyethylene terephthalate (PET), acrylonitrile butadiene styrene (ABS), and polyphenylene ether (PPE). The initial and various chemical treatments of natural fibers, their effect on the thermal and performance properties of natural fiber engineering thermoplastic composites, and the advanced treatment of epoxy coatings are reviewed. Applications of natural fiber-reinforced thermoplastic composites in the construction and automotive industries, as well as in other applications, are outlined. It was established that the adhesion and thermal stabilities between polymer matrix and natural fibers are better improved by surface coating with diluted epoxy resin thermoset. This eventually improved the overall thermal and performance properties of the resultant composites and will serve as a data bank and guide for manufacturers and future research directions using high-end engineering polymers with higher processing temperatures. GRAPHICAL ABSTRACT Surface coating treatment and composites production processes for improving the interface and mechanical and thermal properties of epoxy-coated natural (kenaf) fiber-filled engineering thermoplastics composites
- Open Access
- 2 January 2023
- Published by Taylor & Francis in Advanced Manufacturing: Polymer & Composites Science
- Vol. 9 (1)
Effect of reprocessing on the service life properties of glass fiber-reinforced in-house polypropylene waste composites
Reprocessing of synthetic fiber-reinforced thermoplastics for reuse in the design of structural components applications is important owing to their non-biodegradability. This study evaluates the effect of reprocessing on the service life properties of in-house polypropylene wastes reinforced with E-glass fiber. Composite materials containing 10 mm length glass fiber (GF) and recycled polypropylene were manufactured with 10 wt% GF and subjected to five reprocessing cycles via extrusion and compression molding under similar conditions. Properties such as mechanical, melt flow index (MFI), thermogravimetric analysis (TGA), Fourier transform infrared (FTIR) spectroscopy, x-ray diffraction (XRD), and scanning electron microscopy (SEM) analysis were used to analyze the effect of reprocessing on the composites. The results obtained revealed that the composites’ properties diminished with successive reprocessing. The thermal study showed reductions in the thermal stabilities with a drop in onset degradation temperature from 338.07 to 245.15 °C after five runs, indicating an increase in the polymer chain molecular movement and less rigidity due to shorter chains provided by X-ray diffraction analysis with reduced peak intensities, average crystallite sizes, and degree of crystallinities but no destruction of the main functional groups was observed with the spectral studies. An increase in the MFI (6 g/10–17.88 g/10 min) indicated the possible loss of complex viscosity and damage in molecular weight for the reprocessed matrix. Reinforced in-house PP plastics can, therefore, be reprocessed twice only for the same product except with the addition of either virgin PP or other materials to compensate for the lost properties and help manufacturers save costs. Graphical Abstract
- 2 January 2023
- Published by Taylor & Francis in Advanced Manufacturing: Polymer & Composites Science
- Vol. 9 (1)
Open AccessEffect of reprocessing on the service life properties of glass fiber-reinforced in-house polypropylene waste composites
Reprocessing of synthetic fiber-reinforced thermoplastics for reuse in the design of structural components applications is important owing to their non-biodegradability. This study evaluates the effect of reprocessing on the service life properties of in-house polypropylene wastes reinforced with E-glass fiber. Composite materials containing 10 mm length glass fiber (GF) and recycled polypropylene were manufactured with 10 wt% GF and subjected to five reprocessing cycles via extrusion and compression molding under similar conditions. Properties such as mechanical, melt flow index (MFI), thermogravimetric analysis (TGA), Fourier transform infrared (FTIR) spectroscopy, x-ray diffraction (XRD), and scanning electron microscopy (SEM) analysis were used to analyze the effect of reprocessing on the composites. The results obtained revealed that the composites’ properties diminished with successive reprocessing. The thermal study showed reductions in the thermal stabilities with a drop in onset degradation temperature from 338.07 to 245.15 °C after five runs, indicating an increase in the polymer chain molecular movement and less rigidity due to shorter chains provided by X-ray diffraction analysis with reduced peak intensities, average crystallite sizes, and degree of crystallinities but no destruction of the main functional groups was observed with the spectral studies. An increase in the MFI (6 g/10–17.88 g/10 min) indicated the possible loss of complex viscosity and damage in molecular weight for the reprocessed matrix. Reinforced in-house PP plastics can, therefore, be reprocessed twice only for the same product except with the addition of either virgin PP or other materials to compensate for the lost properties and help manufacturers save costs. Graphical Abstract
- 2 January 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (10)
Effect of glass fiber loading and reprocessing cycles on the mechanical, thermal, and morphological properties of isotactic polypropylene composites
In this study, a preliminary finding is carried out to obtain the optimum E‐glass fiber content in polypropylene (PP) plastic products using loadings of 5, 10, 20, 30, and 40 wt%. The formulation with the optimum loading of 10 wt% glass fiber was reprocessed 10 times via extrusion and compression molding techniques to simulate actual recycling and impacts on service life properties such as mechanical, toughness, chemical, thermal, composition, and morphology. In the result, mechanical properties were lost after each reprocessing without effect on the chemical properties and elemental compositions. The thermal studies showed a decrease in degradation temperatures with the onset degradation temperature (TOnset) for the one‐time reprocessed PP recorded at 336.93°C with a maximum rate of weight loss (TMax) at 427.68°C which further reduced to 259.90°C (TMax of 388.47°C) after 10 extrusion run showing one‐step decomposition patterns. This work provides that glass fiber‐reinforced plastics should not be reprocessed beyond 3 times except when refreshed with the addition of virgin PP to make up for the lost property. This will be very useful for manufacturers who want to simultaneously save costs (retain profit margin) and maintain the environment.
- 2 January 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (10)
Effect of glass fiber loading and reprocessing cycles on the mechanical, thermal, and morphological properties of isotactic polypropylene composites
In this study, a preliminary finding is carried out to obtain the optimum E‐glass fiber content in polypropylene (PP) plastic products using loadings of 5, 10, 20, 30, and 40 wt%. The formulation with the optimum loading of 10 wt% glass fiber was reprocessed 10 times via extrusion and compression molding techniques to simulate actual recycling and impacts on service life properties such as mechanical, toughness, chemical, thermal, composition, and morphology. In the result, mechanical properties were lost after each reprocessing without effect on the chemical properties and elemental compositions. The thermal studies showed a decrease in degradation temperatures with the onset degradation temperature (TOnset) for the one‐time reprocessed PP recorded at 336.93°C with a maximum rate of weight loss (TMax) at 427.68°C which further reduced to 259.90°C (TMax of 388.47°C) after 10 extrusion run showing one‐step decomposition patterns. This work provides that glass fiber‐reinforced plastics should not be reprocessed beyond 3 times except when refreshed with the addition of virgin PP to make up for the lost property. This will be very useful for manufacturers who want to simultaneously save costs (retain profit margin) and maintain the environment.