BABibinur Akhymbayeva

Bibinur Akhymbayeva

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bibinur Akhymbayeva has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • SHOCK-WAVE STIMULATION FOR DYNAMIC NEAR-WELLBORE TREATMENT IN TIGHT RESERVOIRS

    by B.S. Akhymbayeva, D.A. Omarova, B.K. Mauletbekova

    The paper presents the results of theoretical and hydrodynamic substantiation of shockwave stimulation parameters for dynamic near-wellbore treatment and skin-factor reduction in tight reservoirs. The study is based on actual geological and technical data from production wells No. 45 and No. 47 of the Lower Visean substage at the «Х» field. A two-dimensional axisymmetric finite element model based on the Biot-Frenkel dynamic poroelasticity theory was developed, which accounts for the radial change in fluid viscosity and density within the zone of deep invasion of heavy mud filtrate (1.90 g/cm³). Through numerical simulation, the optimal frequency range of the shock pulse (10–15 Hz) was determined. It was established that the pressure wave with an amplitude of up to 4.5 MPa generated by the hydraulic impulse system exceeds the tensile strength of the rock (σt = 2.8 MPa) and ensures the opening of a microfracture network according to Coulomb’s cubic law at a distance of up to 2.0 m from the wellbore wall at a frequency of 10 Hz. The practical significance lies in the elimination of the mud cake screen formed under high overbalance conditions during the primary disclosure of an ultra-tight formation (porosity up to 0.15%, permeability from 0.001 mD). The implementation of the proposed regimes allows for a reduction in the calculated skin factor from critical 8.8 down to 0.4–1.5, which provides a 2.4 to 3.1-fold increase in the predicted well productivity index.

  • Techno-economic justification of TAML 4 systems for zonal isolation in field “X”

    by A.M. Seilkhanov, D.N. Delikesheva, B.S. Akhymbayeva

    This study addresses the critical challenge of extending the economic life of mature fields characterized by high water cuts and heterogeneous drainage. Focusing on the “X” field (PreCaspian Basin), the research evaluates the limitations of conventional sidetracking (ST) versus advanced Multilateral Drilling (MLD). Forensic analysis of production logs from existing wells reveals that single-bore sidetracks suffer from rapid sediment accumulation and mechanical window deformation. Crucially, an integrity assessment using azimuthal acoustic scanning (VAK-SK) identified a systemic failure in liner cementing (46% poor bonding) attributed to gravitational casing eccentricity. To mitigate these risks, this paper proposes an engineered TAML Level 4 dual-lateral design integrating Rotating Liner Technology and Passive Inflow Control Devices (ICD). Theoretical modeling confirms that ICDs neutralize the heel-toe effect, while rotation ensures zonal isolation. Economic analysis demonstrates that despite a 60% CAPEX premium, the MLD strategy yields a positive NPV by Year 3 and extends the plateau production period. The study provides a validated framework for selecting junction complexity in fields with weak formation integrity.

  • Open Access

    Innovative technology for the reuse of spent drilling fluids in production well drilling using a hydraulic disperser

    by Bakytzhan Kaliyev, Beibit Myrzakhmetov, Bibinur Akhymbayeva, Gulzada Mashatayeva, Bulbul Mauletbekova

    This article explores an innovative approach to the disposal of used water-based spent drilling fluids (SDF) utilized in the drilling of production wells at uranium deposits, with a case study based on the operations of SD «Inkai». A technological solution is proposed, centered on the use of a hydrodynamic disperser that enables efficient phase separation of drilling fluids, reduction of residual moisture in solid fractions, and the potential for reuse of the liquid phase. The geological and hydrogeological conditions of the deposit are examined in detail, along with the composition and properties of the drilling fluids, challenges associated with their accumulation and disposal, and the legal and regulatory framework of the Republic of Kazakhstan governing drilling waste management. The design of the proposed disperser is presented, the technological process is described, and its advantages over traditional disposal methods are substantiated. The article also analyzes the ecological, operational, and resource-saving aspects related to the implementation of the proposed technology within existing drilling systems.

  • DEVELOPMENT MODELING OF MATURE FIELD X USING EOR METHODS IN

    by Kazakh-British Technical University, K. Kabdula, A.K. Abdukarimov, B.S. Akhymbayeva, Satbayev University

    This study examines the use of miscible gas injection for Enhanced Oil Recovery (EOR) in Field “X” in comparison to sour gas injection (SGI) and chemical flooding alternatives. The goal is to determine which EOR method offers the best combination of technical effectiveness and economic feasibility. A static geological model of Field X was developed using Schlumberger Petrel and reservoir simulations (covering primary, secondary, and tertiary recovery stages) were run in the INTERSECT simulator. The simulations indicate that miscible gas injections markedly increase hydrocarbon recovery while keeping costs low. An economic evaluation (considering capital and operating costs and net present value) revealed that reinjecting sour gas yields the highest NPV, primarily due to its minimal operating expenses. In contrast, chemical EOR techniques – specifically alkaline–surfactant–polymer (ASP) flooding and polymer-alternating-water (PAW) injection – delivered only marginal additional oil recovery, which is not economically viable given their high chemical costs.

  • Analiza wykorzystania składu polimerów we wdrażaniu technologii korygujących przepływ

    by Bibinur Akhymbayeva, Serik Kabdulov, Jamilyam Ismailova, Bulbul Mauletbekova, Aidana Myrzabekova

    Niniejsze analiza bada skuteczność różnych typów polimerów, w tym polimerów modyfikowanych hydrofobowo, polisacharydów i syntetycznych poliakrylamidów, w zwiększaniu odzysku ropy naftowej i zmniejszaniu wpływu na środowisko. Celem tych badań jest kompleksowa ocena skuteczności składów polimerów w technologiach korygujących przepływ w produkcji ropy naftowej. Badania eksperymentalne przeprowadzone na Uniwersytecie Satbayeva w 2024 r. oceniały roztwory polimerów w symulowanych warunkach złoża o wysokiej temperaturze i wysokim zasoleniu, badając ich potencjał w zakresie poprawy lepkości cieczy, kontrolowania procesów filtracji i optymalizacji ekstrakcji węglowodorów. Badania ujawniły znaczące zalety technologiczne kompozycji polimerowych, wykazując ich zdolność do tworzenia stabilnych emulsji, zmniejszania odzysku wody i poprawy profili wypierania ropy. Polimery modyfikowane hydrofobowo zwiększyły lepkość płynu złożowego o 30%, podczas gdy syntetyczne poliakrylamidy wykazały niezwykłą zdolność adaptacji do różnych warunków geologicznych. Analiza ekonomiczna wskazała, że technologie polimerowe mogą zwiększyć wydobycie ropy o około 43% bez konieczności dodatkowego wiercenia odwiertów, co zmniejsza nakłady inwestycyjne. Pomimo wyzwań związanych ze stabilnością temperatury i względami ekonomicznymi, badanie stwierdza, że kompozycje polimerowe stanowią obiecującą strategię zrównoważonej i wydajnej produkcji ropy, oferując elastyczność technologiczną i lepsze zarządzanie zasobami.

  • Comparative analysis of the shock-hydraulic system for optimizing the process of multi-hole drilling

    by Kazakh-British Technical University, D.E. Starikov, A.K. Abdukarimov, B.S. Akhimbaeva, Satbayev University

    This paper presents a comparative analysis of percussion-hydraulic systems aimed at optimizing the multilateral drilling process. The research focuses on evaluating the effectiveness of hydraulic pulse interaction systems in horizontal and directional well drilling, addressing the inherent limitations of traditional drilling techniques where the absence of sufficient static load reduces penetration rates. The study investigates the potential of hydraulic percussion tools to improve drilling speed, enhance borehole stability, and mitigate operational issues typically encountered in low-permeability and vertically fractured reservoirs. Key design parameters of hydraulic pulse systems, including curvature radius, axial loads, and wellbore trajectory profiles, are examined to ensure precise directional control and efficient rock destruction. Advanced mathematical models are employed to optimize parameters such as pulse frequency, impact energy, and crown rotation speed. The integration of rotary-impact techniques alongside traditional methods is explored to address challenges in drilling complex geologic formations. Furthermore, the paper proposes novel improvements to existing hydraulic systems, including enhanced spring configurations that ensure tool operation even in cases of partial spring failure. Comparative analyses with technologies such as Baker Hughes' AutoTrak and Sperry-Sun's GeoPilot illustrate the advantages and limitations of percussion-hydraulic systems in practical applications. The research concludes that the adoption of these systems significantly improves drilling efficiency, reduces costs, and enables effective multilateral well construction under challenging conditions. This study's outcomes are expected to contribute to the further development of drilling technologies in Kazakhstan and other oil-producing regions, offering promising prospects for commercialization and practical implementation.

  • Analysis of the use of polymer composition in the implementation of flow correction technologies

    by Satbayev University, B. Akhymbayeva

    The study was carried out to assess the effectiveness of the use of polymer formulations in flow correction technologies in order to increase oil production and reduce water yield in the field of oil production. In the study, experiments were carried out to determine the viscosity of the polymer, increase oil release, reduce water release and the length of the contact zone with the polymer. The study showed that the use of polymer compounds in flow correction technologies significantly increases the efficiency of oil production. Hydrophobic modified polymers and polysaccharides such as xanthan gum improve the viscosity of the layer fluids, which contributes to the uniform extraction of oil. Synthetic polyacrylamides have proven to be resistant to high temperatures and saline solutions, which ensures stable performance under different layer conditions. The use of polymers also made it possible to reduce water consumption and reduce water flow, which had a positive effect on environmental indicators. As a result, the use of polymer compounds in flow correction technologies increased oil production without drilling new wells and improved the economic efficiency of projects. These results show the potential of polymer technologies in the modern oil production sector. The study also found that polymer compounds contribute to improving the filtration profile, which reduces the formation of unnecessary channels and contributes to the effective extraction of oil. The introduction of these technologies showed a decrease in production costs due to reducing the volume of rising water and increasing the overall productivity of Wells. The practical significance of the study is to show that the use of polymer compounds in flow correction technologies can significantly increase the efficiency of oil production and improve environmental indicators, which opens up new opportunities for optimizing oil production processes.

  • Analysis of the use of hydraulic shock technology in drilling of hard rocks

    by Satbayev University, B.S. Akhymbayeva

    The relevance of this study stems from the critical role that groundwater plays in providing the population with high-quality drinking water. Groundwater is extensively utilized for industrial purposes, housing and communal services, irrigation of pastures, and other needs. The study aims to explore the specifics of drilling hard rocks using hydraulic impact technology. The research methodology is based on laboratory bench tests conducted from January 6, 2021, to April 28, 2021, at the educational and production workshops of the Department of «Technological Machines and Equipment» at the Mining and Metallurgical Institute of the National Academy of Sciences «KazNITU named after K.I. Satpayev». The research also incorporated methods of synthesis and information analysis, and at the final stage, an analysis of scientific literature on the subject was conducted. The bench tests yielded the main design parameters of a hydraulic pulse generator effective for use with impact machines, including the main geometric parameter Fd/FK (3.78), ld - 70-100 mm, 1h=35 mm, 1c=24-30 mm, FKp=254.34 mm², Rd=981.25 mm², and F=304.72 mm². The tests aimed to optimize the primary geometric parameters of the hydraulic pulse generator, analyze the distribution of the working flow in front of the jet apparatus, and measure the ejection coefficient and pressure drop to refine the experimental setup for downhole conditions. The practical significance of this research is that it serves as a foundational study for further exploration of hard rock drilling using hydraulic impact technology, benefiting both practitioners and theorists in the field.

  • Optimizing oil recovery and emissions reduction through co2 injection in mature offshore fields

    by Satbayev University, B. Akhymbayeva

    The article explores the potential of CO2 injection technology for enhanced oil recovery (EOR) and simultaneous reduction of carbon emissions through storage in oil reservoirs and aquifers. The study focuses on 23 oil fields on the Norwegian Continental Shelf, identified as promising candidates for implementing this technology. The model used in the research assesses the economic and technical feasibility of CO2 injection, along with the integration of EOR and long-term carbon storage. The primary goal is to demonstrate that injecting 70 million tons of CO2 annually over 40 years can result in an additional oil recovery of 5.9%-7.6% of the original oil in place, equivalent to 276-351 million cubic meters. Excess CO2 can be stored in aquifers, further contributing to the reduction of carbon emissions. The article outlines key aspects of the study, including economic and technical parameters, such as costs associated with CO2 transportation, storage, and drilling of new wells, as well as various oil and CO2 price scenarios. The environmental benefits of the project are highlighted, showing that the significant CO2 retained in oil reservoirs and aquifers compensates for emissions from the combustion of recovered oil. The study also discusses the features of the model, including scenarios for continuous CO2 injection and considerations of infrastructure costs. The article emphasizes the importance of developing and implementing such projects in the context of global climate change mitigation efforts and points to the significant potential of CO2 injection technology for the oil industry. The aim of this article is to evaluate the feasibility and potential benefits of large-scale CO2 injection for enhanced oil recovery (EOR) and long-term carbon storage in oil fields and aquifers. The study seeks to demonstrate how CO2 injection can increase oil recovery rates while simultaneously reducing carbon emissions, providing a comprehensive technical-economic assessment of the process. Through the analysis of 23 oil fields on the Norwegian Continental Shelf, the article aims to present the economic, environmental, and operational advantages of integrating CO2 storage with EOR operations.

  • Features of drilling horizontal wells with gas-liquid shock-ejector shells in difficult mining and geological conditions

    by Satbayev University, B.S. Akhymbayeva, S.Z. Kabdulov, Kazakh-British Technical University, B.A. Myrzakhmetov, B.Z. Kaliyev, T.A. Kuandykov

    This article examines the features of drilling horizontal wells with gas-liquid shock-ejector shells in difficult mining and geological conditions, namely in boulder-pebble deposits. The technology of drilling large boulders is considered. In addition, to study the processes of energy transfer and shock pulses from the drilling shell to the bottom of the well during the sinking of boulders, the authors conducted appropriate theoretical studies and provided calculations of the stages of the introduction of the tool into the rock. Based on theoretical studies, drilling analysis, calculations of the dependence of boulder movements, several conclusions were obtained on the technology of drilling wells in boulder-nut deposits.