HKHalil Karatay

Halil Karatay

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Halil Karatay has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental and Numerical Analysis of Screw Withdrawal Strength of Cross-Laminated Timbers

    by Seyma Alpaslan, Halil Karatay, Orhan Eren, Mesut Uysal

    This study examines the impact of screw penetration depth and wood species on the SWS of CLT panels, utilizing a combination of experimental testing and FEA to assess performance. CLT panels were fabricated from Uludağ fir and black pine, and screw withdrawal tests were performed at two penetration depths corresponding to two- and three-layer. The average densities of CLTs were 0.44 g/cm3 for Uludağ fir and 0.52 g/cm3 for black pine, with respective moisture contents of 11.37% and 11.08%. The average SWS for Uludağ fir CLTs increased from 9.73 N/mm2 (two-layer) to 11.27 N/mm2 (three-layer), representing a 15.83% enhancement, while black pine CLTs improved from 13.85 N/mm2 to 14.72 N/mm2 (6.28% increase) with an increase in penetration depth from two to three-layer. Statistical analysis confirmed significant effects of both wood species and penetration depth. FEA simulations predicted withdrawal resistances of 2950.41–3115.94 N for Uludağ fir and 3339.19–3969.73 N for black pine, with two and three-layer penetration depths, respectively. The differences between the experimental and numerical results ranged from 3.69% to 50.10%. Approximately 62.50% of comparisons were within an acceptable 24% deviation range for wood materials. The results indicate that denser species and greater penetration depth enhance withdrawal performance, while FEA provides reasonably accurate yet conservative estimates. The developed experimental–numerical framework provides a reliable predictive basis for designing and optimizing screw connections in wooden constructions, contributing to safer, more efficient, and sustainable CLT-based building systems.

  • Open Access

    The diagonal tensile strength of corner joints constructed with different connectors

    by Halil Karatay, Merve Fatma Akbaş, Mesut Uysal

    This study aimed to investigate the strength and stiffness of corner joints for case furniture in the diagonal tension test. For this purpose, joint members were constructed with medium-density fiberboard (MDF) and particleboard (PB) with minifix, butterfly, and trapeze connectors. The study also observed the role of the end distance of the connectors, which was found to be a factor in joint strength and stiffness. According to the results, joints made of MDF performed 16 to 92 % better compared to PB, considering connectors on joints, which was evident due to material properties that MDF were denser by 7.5% and more strengthfull by 177% than PB. The butterfly connectors had the highest strength and stiffness regardless of material type and end distance, followed by trapeze connectors. The joints with minifix connectors had strength and stiffness of 2-3 times lower than others. Moreover, the end distance of 75 mm provided slightly higher joint strength and stiffness compared to those of 50 mm but was not statistically significant. Consequently, butterfly connectors demonstrated markedly the highest strength and stiffness for corner joints of case furniture. Furniture made of MDF should be chosen for higher durability rather than PB.


  • Open Access

    Çapraz lamine kerestelerin sonlu elemanlar metodu ile analizi

    by Halil Karatay, Ergün Güntekin, Mesut Uysal

    Çalışmada, Çapraz Lamine Kerestelerin (ÇLK) Sonlu Elemanlar Metodu (SEM) ile yük altında eğilme davranışları incelenmiş; literatürde yer alan Uludağ göknarı ve karaçam odunundan elde edilen ÇLK’lerin eğilme özellikleri kullanılmış ve çalışma sonuçları ile karşılaştırılmıştır. ANSYS sonlu elemanlar yazılımı kullanılarak ahşap mal-zemenin ortotropik malzeme özellikleri ve laminasyonda kullanılan tutkallama dikkate alınarak modeller oluştu-rulmuştur. Uludağ göknarı odunundan elde edilen ÇLK’lerde malzemenin yük-deformasyon eğrisi 700 N yük uygulamasından sonra lineer bölgeden uzaklaşırken, karaçam odunundan elde edilen ÇLK’lerde ise 1400 N’dan sonra uzaklaşmaktadır. Uludağ göknarı’ndan elde edilen ÇLK’lerde 800 N altındaki deformasyon 10,50 mm iken karacam odunundan elde edilen ÇLK’lerde ise 13,85 mm’dir. Ayrıca, nümerik analizlerden elde edilen yük-deformasyon grafikleri ile deneysel sonuçların gösterildiği verilerdeki yük-deformasyon eğrileri uyumludur. Çalış-manın sonuçları, karaçam ve Uludağ göknarı odunundan elde edilen ÇLK’lerin ortotropik özellikleri kullanılarak bilgisayarlı ortamda simüle edilmesi yerli odun türlerimizin yapı sektöründe kullanılması açısından önem arz etmektedir.

  • Open Access

    Uludağ göknarı ve karaçam odunlarından elde edilen çapraz lamine kerestelerinin eğilme özeliklerinin incelenmesi

    by Mesut Uysal, Orhan Eren, Halil Karatay, Doğan MEMİŞ

    Bu çalışmada, EUROCODE 5 kapsamına alınan yerli iğne yapraklı ağaç türlerinden uludağ göknarı ve karaçam keresteleri ve polivinil asetat (PVAc) tutkalı kullanılarak elde edilen çapraz lamine keresteler (ÇLK) malzemesinin eğilme direnci ve elastikiyet modülü incelenmiştir. 3 katmalı olarak hazırlanan ÇLK’lar 0.4 N/mm2 basınç altında 35°C sıcaklıkta 150 dk süre ile preslenmiştir. Üç nokta eğme deneyi yük-deformasyon eğrileri elde edilen hem masif Uludağ göknarı ve karaçam hem de bu malzemelerden elde edilen ÇLK’ların eğilme direnci ve elastikiyet modülü belirlenmiştir. Masif Uludağ göknarı ve karaçamın eğilme direnci 65 N/mm2 ve 83.8 N/mm2 olarak tespit edilmiştir. Bu malzemelerden elde edilen ÇLK’ların eğilme direnci ise 38.4 N/mm2 ve 64.6 N/mm2 olarak bulunmuştur. Elastikiyet modülünde ise bu değerler sırasıyla, 9093.5 N/mm2, 11068.8 N/mm2, 5273.4 N/mm2 ve 8657.0 N/mm2 olarak belirlenmiştir. Deney sonuçlarına göre karaçam odunundan elde edilen hem masif hem de ÇLK’lar göknar odunundan elde edilenlere göre daha dayanıklı olarak bulunmuştur. Çalışmanın varyans analizi de hem masif hem de ÇLK için odun türünün istatiksel olarak anlamlı bir farklılık gösterdiğini ortaya koymuştur. Sonuç olarak, yerli iğne yapraklı ağaçlarımızın EUROCODE 5 kapsamında alınması, bu malzemelerden ÇLK’ların üretilmesi ve malzemelerin mekanik özelliklerinin belirlenmesi Türkiye ahşap yapı sektöründe bu malzemelerin yapı analizinde ve yapı eleman tasarımında önemlidir.