Lucian Dascalescu
Lucian Dascalescu has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Amar Tilmatine
APELEC Laboratory, Djillali Liabes University of Sidi Bel-Abbes
7 shared publications - Karim Medles
Electrostatics and High Voltage Research, University Djillali Liabes Sidi Bel Abbes, Sidi Bel Abbes, Algeria Algeria 22000
6 shared publications Adrian Mihalcioiu
Ecole Super. d'Ing. de Poitiers, Univ. Inst. of Technol., Angouleme
4 shared publications- Abdelber Bendaoud
Djillali Liabes University of Sidi Bel-Abbes
3 shared publications Simona Vlad
Department of Electrical Engineering , Cluj-Napoca, Romania
3 shared publications- Adrian Samuila
High Intensity Electric Fields Laboratory, Technical University of Cluj Napoca , Cluj Napoca , Romania
2 shared publications
Latest Publications
- 1 October 2017
- Published by Elsevier in Journal of Electrostatics
- Vol. 89, 59-68
Experimental study of a tribo-aero-electrostatic separator for finely-grinded matter
- 1 October 2017
- Published by Elsevier in Journal of Electrostatics
- Vol. 89, 59-68
Experimental study of a tribo-aero-electrostatic separator for finely-grinded matter
- 8 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 51 (5) , 4145-4150
Experimental Modeling of a New Triboelectrostatic Separation Process for Micronized Plastics
Triboelectrostatic separation of millimeter-size granular plastic mixtures is widely used in recycling industry. However, electrostatic separation of micronized plastics is still inefficient since the adhesion and aerodynamic forces surpass the electric force. The aim of this paper is to optimize a new separation process for mixed fine granular plastics based on a fluidized bed tribocharging system. A pair of opposite high-voltage parallel plate electrodes are immersed in that bed and undergo a vertical alternating movement. The fine polyvinyl chloride particles of average size 0.1-mm particles to be separated are tribocharged using a fluidization air provided by a variable-speed blower. The charged particles are pinned to the electrodes of opposite polarities. The separation depends on several factors: the electric field, the speed of the electrode movement, the mass of the granular product, and the fluidization rate. The latter was the most significant factor, and the interval between the electrodes should not be less than 2 cm to avoid corona discharge.
- 8 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 51 (5) , 4145-4150
Experimental Modeling of a New Triboelectrostatic Separation Process for Micronized Plastics
Triboelectrostatic separation of millimeter-size granular plastic mixtures is widely used in recycling industry. However, electrostatic separation of micronized plastics is still inefficient since the adhesion and aerodynamic forces surpass the electric force. The aim of this paper is to optimize a new separation process for mixed fine granular plastics based on a fluidized bed tribocharging system. A pair of opposite high-voltage parallel plate electrodes are immersed in that bed and undergo a vertical alternating movement. The fine polyvinyl chloride particles of average size 0.1-mm particles to be separated are tribocharged using a fluidization air provided by a variable-speed blower. The charged particles are pinned to the electrodes of opposite polarities. The separation depends on several factors: the electric field, the speed of the electrode movement, the mass of the granular product, and the fluidization rate. The latter was the most significant factor, and the interval between the electrodes should not be less than 2 cm to avoid corona discharge.
- 1 October 2013
- Published by Elsevier in Journal of Electrostatics
- Vol. 71 (5) , 867-874
Numerical simulation of the continuous operation of a tribo-aero-electrostatic separator for mixed granular solids
- 1 October 2013
- Published by Elsevier in Journal of Electrostatics
- Vol. 71 (5) , 867-874
Numerical simulation of the continuous operation of a tribo-aero-electrostatic separator for mixed granular solids
- 14 May 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 49 (6) , 2375-2381
Experimental Modeling of a New Triboelectrostatic Separation Process for Mixed Granular Polymers
Recycling of plastics from industrial wastes requires appropriate sorting technologies, such as the free-fall electrostatic separation of tribocharged granular materials. This paper introduces a novel electrostatic separation process characterized by the fact that the granules to be separated are charged in a fluidized bed affected by an electric field generated by two rotating roll electrodes. The experimental design methodology was employed for the modeling and optimization of the separation of a mixture composed of acrylonitrile butadiene styrene (ABS) and high-impact polystyrene (HIPS), originating from shredded obsolete computer cases. After processing the experimental data using the MODDE 5.0 software, the masses of ABS, HIPS, and middling collected after separation were expressed as quadratic functions of three of the control variables of the process: 1) duration; 2) speed of the fluidization air; and 3) high voltage applied to the electrode system. The obtained results demonstrate the effectiveness of this method for the separation of plastics from granular wastes.
- 14 May 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 49 (6) , 2375-2381
Experimental Modeling of a New Triboelectrostatic Separation Process for Mixed Granular Polymers
Recycling of plastics from industrial wastes requires appropriate sorting technologies, such as the free-fall electrostatic separation of tribocharged granular materials. This paper introduces a novel electrostatic separation process characterized by the fact that the granules to be separated are charged in a fluidized bed affected by an electric field generated by two rotating roll electrodes. The experimental design methodology was employed for the modeling and optimization of the separation of a mixture composed of acrylonitrile butadiene styrene (ABS) and high-impact polystyrene (HIPS), originating from shredded obsolete computer cases. After processing the experimental data using the MODDE 5.0 software, the masses of ABS, HIPS, and middling collected after separation were expressed as quadratic functions of three of the control variables of the process: 1) duration; 2) speed of the fluidization air; and 3) high voltage applied to the electrode system. The obtained results demonstrate the effectiveness of this method for the separation of plastics from granular wastes.
- 8 April 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 49 (4) , 1773-1780
Modeling and Optimization of a Roll-Type Electrostatic Separation Process Using Artificial Neural Networks
The aim of this paper is the development of a procedure for the optimization of electrostatic separation processes using artificial neural networks (ANNs) in association with genetic algorithms. The objective was to maximize the insulation product, the control variables being the high voltage that supplies the electrode system and the rotation speed of the roll electrode. The ANN model is compared with that obtained using the classical experimental design methodology. The predicted optimum is confirmed by experiment.
- 8 April 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 49 (4) , 1773-1780
Modeling and Optimization of a Roll-Type Electrostatic Separation Process Using Artificial Neural Networks
The aim of this paper is the development of a procedure for the optimization of electrostatic separation processes using artificial neural networks (ANNs) in association with genetic algorithms. The objective was to maximize the insulation product, the control variables being the high voltage that supplies the electrode system and the rotation speed of the roll electrode. The ANN model is compared with that obtained using the classical experimental design methodology. The predicted optimum is confirmed by experiment.
- 22 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 48 (2) , 816-822
Numerical Simulation of Tribo-Aero-Electrostatic Separation of Mixed Granular Solids
Numerical simulation can be a powerful tool in the research and development of any new electrostatic process. The aim of the present work is to introduce a simple mathematical model for simulating the outcome of a recently patented tribo-aero-electrostatic separation process for binary mixtures of granular materials. The process is characterized by the fact that the charging of the granules is produced in a fluidized bed device, in the presence of an electric field. The mathematical model assumed that the probability of a granule to be separated can be expressed as a function of the number of impacts with granules belonging to the other class of materials. When this probability was given by a normal distribution law, the results of the simulations differed significantly from those of an experiment conducted with a granular mixture of polyamide and polycarbonate particles, in a laboratory tribo-aero-electrostatic separator. In order to improve the predictive capability of the simulations, a polynomial function derived from the regression of the experimental data was employed for expressing the same probability. Thus, it was possible to calculate the evolution in time of the mass of granules separated at the electrodes for various compositions of the granular mixture. The computed results were in good agreement with the experiments.
- 22 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 48 (2) , 816-822
Numerical Simulation of Tribo-Aero-Electrostatic Separation of Mixed Granular Solids
Numerical simulation can be a powerful tool in the research and development of any new electrostatic process. The aim of the present work is to introduce a simple mathematical model for simulating the outcome of a recently patented tribo-aero-electrostatic separation process for binary mixtures of granular materials. The process is characterized by the fact that the charging of the granules is produced in a fluidized bed device, in the presence of an electric field. The mathematical model assumed that the probability of a granule to be separated can be expressed as a function of the number of impacts with granules belonging to the other class of materials. When this probability was given by a normal distribution law, the results of the simulations differed significantly from those of an experiment conducted with a granular mixture of polyamide and polycarbonate particles, in a laboratory tribo-aero-electrostatic separator. In order to improve the predictive capability of the simulations, a polynomial function derived from the regression of the experimental data was employed for expressing the same probability. Thus, it was possible to calculate the evolution in time of the mass of granules separated at the electrodes for various compositions of the granular mixture. The computed results were in good agreement with the experiments.
- 19 May 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 47 (4) , 1922-1928
Tribocharging of Mixed Granular Plastics in a Fluidized-Bed Device
The output of any electrostatic separation process is strongly dependent on the effectiveness of particle charging. The aim of the present paper is to evaluate the effects of several factors that might influence the efficiency of a fluidized bed tribocharger, in the presence of an electric field orthogonally oriented to the direction of the fluidization air. The experiments were carried out on several synthetic mixtures of binary granular mixtures. The velocity of the fluidization air, the duration of the tribocharging process, and the composition of the mixture were the three process variables investigated. Whenever possible, the effects of these variables on the output of the process (i.e., the mass and the charge of the granules collected at the electrodes), were evaluated using the experimental design methodology. The results of full- and composite-factorial experimental designs were analyzed with a commercial software (MODDE 5.0, Umetrics). The effectiveness of the charging process was found to depend significantly on each of these factors. The propitious aerodynamic design of the device is a prerequisite for the successful industry application of the technique.
- 19 May 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 47 (4) , 1922-1928
Tribocharging of Mixed Granular Plastics in a Fluidized-Bed Device
The output of any electrostatic separation process is strongly dependent on the effectiveness of particle charging. The aim of the present paper is to evaluate the effects of several factors that might influence the efficiency of a fluidized bed tribocharger, in the presence of an electric field orthogonally oriented to the direction of the fluidization air. The experiments were carried out on several synthetic mixtures of binary granular mixtures. The velocity of the fluidization air, the duration of the tribocharging process, and the composition of the mixture were the three process variables investigated. Whenever possible, the effects of these variables on the output of the process (i.e., the mass and the charge of the granules collected at the electrodes), were evaluated using the experimental design methodology. The results of full- and composite-factorial experimental designs were analyzed with a commercial software (MODDE 5.0, Umetrics). The effectiveness of the charging process was found to depend significantly on each of these factors. The propitious aerodynamic design of the device is a prerequisite for the successful industry application of the technique.
- 2 September 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 46 (6) , 2157-2164
Corona Separation of Fly Ash
The possibility of converting fly-ash waste into a raw material for cement industry and other applications justifies the investigation of new beneficiation techniques, including those using electrostatic forces. The aim of this paper was to demonstrate the effectiveness of a modified roll-type corona separator in the processing of this material. Three different laboratory models of such separators were evaluated. The analysis of the experimental results pointed out the main problems that should be solved prior to the industry application of corona separators for fly-ash beneficiation. A numerical model of fly-ash behavior in roll-type corona separators enabled a thorough examination of the factors that influence the efficiency of the process and should be considered in the final design.
- 2 September 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 46 (6) , 2157-2164
Corona Separation of Fly Ash
The possibility of converting fly-ash waste into a raw material for cement industry and other applications justifies the investigation of new beneficiation techniques, including those using electrostatic forces. The aim of this paper was to demonstrate the effectiveness of a modified roll-type corona separator in the processing of this material. Three different laboratory models of such separators were evaluated. The analysis of the experimental results pointed out the main problems that should be solved prior to the industry application of corona separators for fly-ash beneficiation. A numerical model of fly-ash behavior in roll-type corona separators enabled a thorough examination of the factors that influence the efficiency of the process and should be considered in the final design.
- 10 May 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 46 (4) , 1586-1592
Factors That Influence the Decay Rate of the Potential at the Surface of Nonwoven Fabrics After Negative Corona Discharge Deposition
Surface potential decay (SPD) measurements are considered as the most appropriate technique for the investigation of the corona charging of dielectric surfaces. The aim of the experiments reported in the present paper was to point out the peculiarities of SPD in the case of nonhomogeneous dielectrics, such as the nonwoven fabrics employed for heat, ventilation, and air conditioning. This paper reports experimental data collected on two types of polypropylene (PP) media, characterized by different fiber diameters. The experiments were performed on 60 mm × 50 mm samples of nonweaved sheets of PP (sheet thickness: 400 μm; average fiber diameter: 20 μm), in ambient air (temperature: 18°C to 22°C; relative humidity: 25% to 60%). The samples were charged for 10 s by exposing them to the negative corona discharge, using a triode-type electrode arrangement, energized from a dc high-voltage supply. Their surface potential was then measured with an electrostatic voltmeter. The measured data indicate that the charge of the filter is limited by the local discharges that occur inside the fibrous dielectric.
- 10 May 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 46 (4) , 1586-1592
Factors That Influence the Decay Rate of the Potential at the Surface of Nonwoven Fabrics After Negative Corona Discharge Deposition
Surface potential decay (SPD) measurements are considered as the most appropriate technique for the investigation of the corona charging of dielectric surfaces. The aim of the experiments reported in the present paper was to point out the peculiarities of SPD in the case of nonhomogeneous dielectrics, such as the nonwoven fabrics employed for heat, ventilation, and air conditioning. This paper reports experimental data collected on two types of polypropylene (PP) media, characterized by different fiber diameters. The experiments were performed on 60 mm × 50 mm samples of nonweaved sheets of PP (sheet thickness: 400 μm; average fiber diameter: 20 μm), in ambient air (temperature: 18°C to 22°C; relative humidity: 25% to 60%). The samples were charged for 10 s by exposing them to the negative corona discharge, using a triode-type electrode arrangement, energized from a dc high-voltage supply. Their surface potential was then measured with an electrostatic voltmeter. The measured data indicate that the charge of the filter is limited by the local discharges that occur inside the fibrous dielectric.
- 19 May 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 45 (3) , 1086-1094
Capability Evaluation and Statistical Control of Electrostatic Separation Processes
The variability of the outcome is often deplored by the users of electrostatic separation equipment. A slight modification of the composition of the processed material, a change in the environmental conditions, or an alteration of the electrode configuration may cause objectionable fluctuation of product quality. Thus, the purity of the copper product recovered from electric cable wastes can easily diminish from 98%, which is fully acceptable for recycling purposes, to a value below the standard level of 97%. This paper is written with the aim of showing how statistical process control methods could contribute to the improvement of users' overall satisfaction. In order to validate a procedure for evaluating the short- and long-term capabilities of the electrostatic separation process, the authors carried out a series of experiments on subgroups of chopped electric cable wastes, which are similar to those currently processed in the recycling industry (95% polyvinyl chloride; 5% copper). The first set of experimental data showed that an ldquoin-controlrdquo electrostatic separation process can easily satisfy the level of performance required by the customers (i.e., a capability index of > 1.33). The same set of data enabled the computation of the upper and lower limits of the R- and X -bar control charts. The second set of experiments was designed to evaluate the ability of these charts to detect the following typical situations of abnormal operation of the electrostatic separation equipment: 1) a change in the composition of the processed material; 2) a failed connection of the static electrode to the high-voltage supply; and 3) the accumulation of dust on the surface of the corona electrode. Based on the authors' experience as consultants for the recycling industry, the following several recommendations have been formulated: 1) Evaluate the capability of the electrostatic separation process by performing no more than ten observations and making use of the confidence indexes; 2) use moving R- and X-bar control charts to obviate the difficulty of sampling; and 3) prepare a ldquoCorrective Actions Guiderdquo for the operators using control charts for monitoring.
- 19 May 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 45 (3) , 1086-1094
Capability Evaluation and Statistical Control of Electrostatic Separation Processes
The variability of the outcome is often deplored by the users of electrostatic separation equipment. A slight modification of the composition of the processed material, a change in the environmental conditions, or an alteration of the electrode configuration may cause objectionable fluctuation of product quality. Thus, the purity of the copper product recovered from electric cable wastes can easily diminish from 98%, which is fully acceptable for recycling purposes, to a value below the standard level of 97%. This paper is written with the aim of showing how statistical process control methods could contribute to the improvement of users' overall satisfaction. In order to validate a procedure for evaluating the short- and long-term capabilities of the electrostatic separation process, the authors carried out a series of experiments on subgroups of chopped electric cable wastes, which are similar to those currently processed in the recycling industry (95% polyvinyl chloride; 5% copper). The first set of experimental data showed that an ldquoin-controlrdquo electrostatic separation process can easily satisfy the level of performance required by the customers (i.e., a capability index of > 1.33). The same set of data enabled the computation of the upper and lower limits of the R- and X -bar control charts. The second set of experiments was designed to evaluate the ability of these charts to detect the following typical situations of abnormal operation of the electrostatic separation equipment: 1) a change in the composition of the processed material; 2) a failed connection of the static electrode to the high-voltage supply; and 3) the accumulation of dust on the surface of the corona electrode. Based on the authors' experience as consultants for the recycling industry, the following several recommendations have been formulated: 1) Evaluate the capability of the electrostatic separation process by performing no more than ten observations and making use of the confidence indexes; 2) use moving R- and X-bar control charts to obviate the difficulty of sampling; and 3) prepare a ldquoCorrective Actions Guiderdquo for the operators using control charts for monitoring.