Co-Optimization of the Preparation Process of Ni-Based Self-Lubricating Coatings by Magneto-Thermal-Assisted Laser Cladding
Open Access
Abstract
To reduce the metallurgical defects that are prone to occur in the preparation of nickel-based self-lubricating coatings, a method of process co-optimization for magneto-thermal-assisted laser cladding of nickel-based self-lubricating coatings is proposed in this paper. The laser energy density, preheating temperature, and electromagnetic intensity are selected as input factors; the prediction models of coating dilution rate, porosity and microhardness are established by the CCD test method; the interactive effects of the magnetic-thermal-assisted cladding process on the coating response are analyzed, and the optimal process parameter combinations are obtained by using the optimization method of MOPSO-AE-TOPSIS. Finally, the coatings under the parameters are successfully prepared. The results show that the optimal process parameter combinations obtained are laser energy density of 56.8 J/mm2, preheating temperature of 350 °C, electromagnetic intensity of 49.1 mT, and the error of the experimental results with this parameter is less than 3% from the algorithm optimization results. When the microstructure of unassisted and magneto-thermal-assisted fields are analyzed by comparison, it is found that the tissues are more homogeneous and finer, and the distribution of graphite is more homogeneous, which proves the effectiveness of the optimization method.Keywords
Funding Information
- National Natural Science Foundation of China (52075544, 2023KXJ-123, 22JK0312, SLGYCX2311, SLGKYXM2306)
- Shaanxi Qinchuangyuan “Scientist + Engineer” Team Construction Project (52075544, 2023KXJ-123, 22JK0312, SLGYCX2311, SLGKYXM2306)
- Shaanxi Provincial Department of Education General Special Scientific Research Program Project (52075544, 2023KXJ-123, 22JK0312, SLGYCX2311, SLGKYXM2306)
- Shaanxi University of Technology Graduate Student Innovation Fund Project (52075544, 2023KXJ-123, 22JK0312, SLGYCX2311, SLGKYXM2306)
- Shaanxi University of Technology Scientific Research Program (52075544, 2023KXJ-123, 22JK0312, SLGYCX2311, SLGKYXM2306)
This publication has 48 references indexed in Scilit:
- Characteristics of dilution and microstructure in laser cladding Ni-Cr-B-Si coating assisted by electromagnetic compound fieldMaterials Letters, 2019
- Microstructure and tribological properties of laser cladded self-lubricating nickel-base composite coatings containing nano-Cu and h-BN solid lubricantsSurface and Coatings Technology, 2019
- Analysis and modeling of melt pool morphology for high power diode laser cladding with a rectangle beam spotOptics and Lasers in Engineering, 2018
- Research on the transformation mechanism of graphite phase and microstructure in the heated region of gray cast iron by laser claddingOptics & Laser Technology, 2018
- In-situ Synthesis of WC/TaC Reinforced Nickel-Based Composite Alloy Coating by Laser CladdingRare Metal Materials and Engineering, 2017
- Influence of electric-magnetic compound field on the WC particles distribution in laser melt injectionSurface and Coatings Technology, 2017
- Laser cladding assisted with an induction heater (LCAIH) of Ni–60%WC coatingJournal of Materials Processing Technology, 2015
- Friction and wear behavior of nickel-alloy-based high temperature self-lubricating composites against Si3N4 and Inconel 718Tribology International, 2014
- Effects of aging treatment on microstructure and tribological properties of nickel-based high-temperature self-lubrication wear resistant composite coatings by laser claddingMaterials Chemistry and Physics, 2014
- A study of Ni-based WC composite coatings by laser induction hybrid rapid cladding with elliptical spotApplied Surface Science, 2008