JGJiangtao Gong

Jiangtao Gong

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jiangtao Gong has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optimization of Milling Process Parameters for Fe45 Laser-Clad Molded Parts Based on the Nondominated Sorting Genetic Algorithm II

    by Jun Zhou, Linsen Shu, Anjun Li, Ning Hu, Jiangtao Gong

    The milling process parameters of laser-clad molded parts have an essential influence on improving the surface quality of the coating. Generally speaking, optimizing a single property often leads to a reduction in another property. In this paper, we systematically investigated a milling process parameter optimization method for Fe45 laser-clad molded parts, and designed L9 (33) sets of orthogonal experiments by taking the spindle speed, feed rate, and cutting depth as input variables, and taking the milling force and material removal rate as optimization indices. The significance ranking of the milling process was analyzed by using the extreme difference method. Then, the multi-objective optimization of the milling process was realized by using the NSGA-II algorithm with the empirical index model as the objective function. The optimum milling parameters obtained were N = 2000 r/min, V = 120.0266 mm/min, and P = 0.45 mm. Finally, the reliability of the optimization results of the algorithm was proved by comparing and verifying the optimal results obtained from the algorithm with the optimal process obtained from the extreme difference analysis. The results provide a theoretical basis for the selection of milling parameters and parameter optimization of laser fusion-coated Fe45 alloys.


  • Open Access

    Influence of Powder Mass Flow Rates on Wear Resistance and Impact Toughness of Inconel 718 Surface Coatings

    by Chaoming Zhang, Linsen Shu, Peiyou Li, Jiangtao Gong, Wei He, Helong Yu

    Optimum laser cladding processing parameters were obtained based on the study of various powder mass flow rates for the repair of 27SiMn steel parts using Inconel 718 powder. In this study, fusion coating process parameters were set according to the influence of powder mass flow rates on fusion coating properties. The cross-sectional microstructure, X-ray diffraction patterns, micro-hardness distribution, friction, wear properties, impact properties, and fracture morphology of the clad layers were investigated for the various process parameters. The results indicate that the volume fraction for the Ni3Fe phase increases and then decreases as the powder mass flow rate increases. The micro-hardness, friction properties, and impact properties of the samples followed the same trend as those of Ni3Fe. At powder mass flow rates up to 20 g/min, microstructures in the cladding layer tended to be uniform with microstructures with fine grains, and micro-hardness and impact toughness reached maximum values of 328.2 HV0.5 and 45.4 J/cm2, respectively, which show better mechanical properties and wear resistance.


  • Open Access

    Co-Optimization of the Preparation Process of Ni-Based Self-Lubricating Coatings by Magneto-Thermal-Assisted Laser Cladding

    by Jiangtao Gong, Linsen Shu, Chaoming Zhang, Jingpeng Qin, Wei He, Anjun Li

    To reduce the metallurgical defects that are prone to occur in the preparation of nickel-based self-lubricating coatings, a method of process co-optimization for magneto-thermal-assisted laser cladding of nickel-based self-lubricating coatings is proposed in this paper. The laser energy density, preheating temperature, and electromagnetic intensity are selected as input factors; the prediction models of coating dilution rate, porosity and microhardness are established by the CCD test method; the interactive effects of the magnetic-thermal-assisted cladding process on the coating response are analyzed, and the optimal process parameter combinations are obtained by using the optimization method of MOPSO-AE-TOPSIS. Finally, the coatings under the parameters are successfully prepared. The results show that the optimal process parameter combinations obtained are laser energy density of 56.8 J/mm2, preheating temperature of 350 °C, electromagnetic intensity of 49.1 mT, and the error of the experimental results with this parameter is less than 3% from the algorithm optimization results. When the microstructure of unassisted and magneto-thermal-assisted fields are analyzed by comparison, it is found that the tissues are more homogeneous and finer, and the distribution of graphite is more homogeneous, which proves the effectiveness of the optimization method.