Chaoming Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chaoming Zhang has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Jiangtao Gong
School of Mechanical Engineering, Shaanxi University of Technology, Hanzhong 723000, China
2 shared publications - Linsen Shu
School of Mechanical Engineering, Shaanxi University of Technology, Hanzhong, China
2 shared publications - Wei He
School of Mechanical Engineering, Shaanxi University of Technology, Hanzhong 723001, China
2 shared publications - Anjun Li
School of Mechanical Engineering, Shaanxi University of Technology, Hanzhong 723000, China
1 shared publication - Helong Yu
National Key Laboratory for Remanufacturing, Army Academy of Armored Forces, Beijing 100072, China
1 shared publication - Jingpeng Qin
School of Mechanical Engineering, Shaanxi University of Technology, Hanzhong 723000, China
1 shared publication
Latest Publications
- Open Access
Influence of Powder Mass Flow Rates on Wear Resistance and Impact Toughness of Inconel 718 Surface Coatings
Optimum laser cladding processing parameters were obtained based on the study of various powder mass flow rates for the repair of 27SiMn steel parts using Inconel 718 powder. In this study, fusion coating process parameters were set according to the influence of powder mass flow rates on fusion coating properties. The cross-sectional microstructure, X-ray diffraction patterns, micro-hardness distribution, friction, wear properties, impact properties, and fracture morphology of the clad layers were investigated for the various process parameters. The results indicate that the volume fraction for the Ni3Fe phase increases and then decreases as the powder mass flow rate increases. The micro-hardness, friction properties, and impact properties of the samples followed the same trend as those of Ni3Fe. At powder mass flow rates up to 20 g/min, microstructures in the cladding layer tended to be uniform with microstructures with fine grains, and micro-hardness and impact toughness reached maximum values of 328.2 HV0.5 and 45.4 J/cm2, respectively, which show better mechanical properties and wear resistance.
Open AccessInfluence of Powder Mass Flow Rates on Wear Resistance and Impact Toughness of Inconel 718 Surface Coatings
Optimum laser cladding processing parameters were obtained based on the study of various powder mass flow rates for the repair of 27SiMn steel parts using Inconel 718 powder. In this study, fusion coating process parameters were set according to the influence of powder mass flow rates on fusion coating properties. The cross-sectional microstructure, X-ray diffraction patterns, micro-hardness distribution, friction, wear properties, impact properties, and fracture morphology of the clad layers were investigated for the various process parameters. The results indicate that the volume fraction for the Ni3Fe phase increases and then decreases as the powder mass flow rate increases. The micro-hardness, friction properties, and impact properties of the samples followed the same trend as those of Ni3Fe. At powder mass flow rates up to 20 g/min, microstructures in the cladding layer tended to be uniform with microstructures with fine grains, and micro-hardness and impact toughness reached maximum values of 328.2 HV0.5 and 45.4 J/cm2, respectively, which show better mechanical properties and wear resistance.
- Open Access
Co-Optimization of the Preparation Process of Ni-Based Self-Lubricating Coatings by Magneto-Thermal-Assisted Laser Cladding
To reduce the metallurgical defects that are prone to occur in the preparation of nickel-based self-lubricating coatings, a method of process co-optimization for magneto-thermal-assisted laser cladding of nickel-based self-lubricating coatings is proposed in this paper. The laser energy density, preheating temperature, and electromagnetic intensity are selected as input factors; the prediction models of coating dilution rate, porosity and microhardness are established by the CCD test method; the interactive effects of the magnetic-thermal-assisted cladding process on the coating response are analyzed, and the optimal process parameter combinations are obtained by using the optimization method of MOPSO-AE-TOPSIS. Finally, the coatings under the parameters are successfully prepared. The results show that the optimal process parameter combinations obtained are laser energy density of 56.8 J/mm2, preheating temperature of 350 °C, electromagnetic intensity of 49.1 mT, and the error of the experimental results with this parameter is less than 3% from the algorithm optimization results. When the microstructure of unassisted and magneto-thermal-assisted fields are analyzed by comparison, it is found that the tissues are more homogeneous and finer, and the distribution of graphite is more homogeneous, which proves the effectiveness of the optimization method.
Open AccessCo-Optimization of the Preparation Process of Ni-Based Self-Lubricating Coatings by Magneto-Thermal-Assisted Laser Cladding
To reduce the metallurgical defects that are prone to occur in the preparation of nickel-based self-lubricating coatings, a method of process co-optimization for magneto-thermal-assisted laser cladding of nickel-based self-lubricating coatings is proposed in this paper. The laser energy density, preheating temperature, and electromagnetic intensity are selected as input factors; the prediction models of coating dilution rate, porosity and microhardness are established by the CCD test method; the interactive effects of the magnetic-thermal-assisted cladding process on the coating response are analyzed, and the optimal process parameter combinations are obtained by using the optimization method of MOPSO-AE-TOPSIS. Finally, the coatings under the parameters are successfully prepared. The results show that the optimal process parameter combinations obtained are laser energy density of 56.8 J/mm2, preheating temperature of 350 °C, electromagnetic intensity of 49.1 mT, and the error of the experimental results with this parameter is less than 3% from the algorithm optimization results. When the microstructure of unassisted and magneto-thermal-assisted fields are analyzed by comparison, it is found that the tissues are more homogeneous and finer, and the distribution of graphite is more homogeneous, which proves the effectiveness of the optimization method.