Effects of sodium copper‐ and sodium iron‐chlorophyllin primers on resin bonding to dentin
- 24 September 2024
- journal article
- research article
- Published by Wiley in European Journal of Oral Sciences
- Vol. 132 (5) , e13017
Abstract
This study evaluated the effects of two chlorophyll derivatives, sodium copper chlorophyllin (Cu‐Chl) and sodium iron chlorophyllin (Fe‐Chl), on the bond strength between a self‐curing luting agent (4‐META/MMA‐TBB resin) and dentin. Five aqueous primers containing 35% 2‐hydroxyethylmethacrylate with 0.007% Cu‐Chl, 0.07% Cu‐Chl, 0.007% Fe‐Chl, 0.07% Fe‐Chl, or neither Cu‐Chl nor Fe‐Chl (no‐Chl) were prepared. The extracted human dentin surfaces were etched with 10% phosphoric acid (10PA), primed, and bonded to a resin block using the 4‐META/MMA‐TBB resin. A conventional etching agent (10‐3) and 10PA without primer (PA/no‐primer) were used as controls. The microtensile bond strength was determined after 48 h. The arithmetic medians for 20 stick specimens were calculated and statistically analyzed using a nonparametric Steel‐Dwass test (α = 0.05). The maximum bond strength was achieved in the 0.007% Cu‐Chl group, followed by those in the 0.07% Cu‐Chl, 0.07% Fe‐Chl, 10‐3, 0.007% Fe‐Chl, no‐Chl, and PA/no‐primer groups. No significant difference was observed between 0.007% Fe‐Chl, 0.07% Fe‐Chl, and 10‐3. The bond strength to dentin etched with 10PA was influenced by the type and concentration of the chlorophyll derivatives applied. Cu‐Chl rather than Fe‐Chl should be useful as a component of surface treatment agents for bonding 4‐META/MMA‐TBB resin to dentin.Keywords
Funding Information
- Japan Society for the Promotion of Science (15K11119, 19K10153)
This publication has 15 references indexed in Scilit:
- The effect of a peroxidase primer on bond strength of three luting systems to dentinEuropean Journal of Oral Sciences, 2009
- Improved wet bonding of methyl methacrylate‐tri‐n‐butylborane resin to dentin etched with ten percent phosphoric acid in the presence of ferric ionsJournal of Biomedical Materials Research Part A, 2004
- Influence of dentinal polyelectrolytes on wet demineralized dentin, a bonding substrateJournal of Biomedical Materials Research Part A, 2003
- Bonded interface between a self-curing resin and dentin primed with a metalloproteinJournal of Biomedical Materials Research, 2003
- Etching characteristics of dentin: effect of ferric chloride in citric acidJournal of Oral Rehabilitation, 2001
- Metal chloride primers for bonding dentine with tri-n-butylborane-initiated luting agentsJournal of Dentistry, 1998
- Use of 2‐isocyanatoethyl methacrylate and iron (II) perchlorate for bonding tri‐ n‐butylborane‐initiated luting agents to dentinEuropean Journal of Oral Sciences, 1998
- Effect of HEMA on bonding to dentinDental Materials, 1992
- Importance of Polymerization Initiator Systems and Interfacial Initiation of Polymerization in Adhesive Bonding of Resin to DentinJournal of Dental Research, 1991
- The promotion of adhesion by the infiltration of monomers into tooth substratesJournal of Biomedical Materials Research, 1982