Effect of Grain Refiner on Fracture Toughness of 7050 Ingot and Plate
Open Access
Abstract
In this paper, two types of grain refining alloys, Al-3Ti-0.15C and Al-5Ti-0.2B, were used to cast two types of 7050 rolling ingots. The effect of Al-3Ti-0.15C and Al-5Ti-0.2B grain refiners on fracture toughness in different directions for 7050 ingots after heat treatment and 7050-T7651 plates was investigated using optical electron microscopy (OEM) and scanning electron microscopy (SEM). Mechanical properties testing included both tensile and plane strain fracture toughness (KIC). The grain size was measured from the surface to the center of the 7050 ingots with two different grain refiners. The fracture surface was analyzed by SEM and energy dispersive spectrometer (EDS). The experiments showed the grain size from edge to center was reduced in 7050 ingots with both the TiC and TiB refiners, and the grain size was larger for ingots with the Al-3Ti-0.15C grain refiner at the same position. The tensile properties of 7050 ingots after heat treatment with Al-3Ti-0.15C grain refiner were 1–2 MPa lower than the ingot with the Al-5Ti-0.2B grain refiner. For the 7050-T7651 100 mm thick plate with the Al-3Ti-0.15C grain refiner, for the L direction, the tensile properties were lower by about 10~15 MPa; for the plate with the Al-3Ti-0.15C refiner than plate with Al-5Ti-0.2B refiner, for the LT direction, the tensile properties were lower by about 13–18 MPa; and for the ST direction, they were lower by about 8–10 MPa compared to that of Al-5Ti-0.2B refiner. The fracture toughness of the 7050-T7651 plate produced using the Al-3Ti-0.15C ingot was approximately 2–6 MPa · higher than the plate produced from the Al-5Ti-0.2B ingot. Fractography of the failed fracture toughness specimens revealed that the path of crack propagation of the 7050 ingot after heat treatment produced from the Al-3Ti-0.15C grain refiner was more tortuous than in the ingot produced from the Al-5Ti-0.2B, which resulted in higher fracture toughness.
Keywords
This publication has 11 references indexed in Scilit:
- Mechanical Properties of Commercial Purity Aluminum Modified by Zirconium Micro-AdditivesCrystals, 2021
- Effect of heat treatment on stress corrosion cracking, fracture toughness and strength of 7085 aluminum alloyTransactions of Nonferrous Metals Society of China, 2014
- Effects of homogenization treatment on recrystallization behavior and dispersoid distribution in an Al–Zn–Mg–Sc–Zr alloyJournal of Alloys and Compounds, 2008
- On the relationship between microstructure, strength and toughness in AA7050 aluminum alloyMaterials Science and Engineering: A, 2003
- Microstructural effects on fracture toughness in AA7010 plateMetallurgical and Materials Transactions A, 2000
- Relationship between fracture toughness, fracutre path, and microstructure of 7050 aluminum alloy: Part II. Multiple micromechanisms-based fracture toughness modelMetallurgical and Materials Transactions A, 1998
- Relationship between fracture toughness, fracture path, and microstructure of 7050 aluminum alloy: Part I. Quantitative characterizationMetallurgical and Materials Transactions A, 1998
- Application of modern aluminum alloys to aircraftProgress in Aerospace Sciences, 1996
- Effect of grain size on the fracture toughness and strength of alloy AK4-1chMetal Science and Heat Treatment, 1983
- Metallurgical factors affecting fracture toughness of aluminum alloysMetallurgical Transactions A, 1975