Mechanical, water absorption, and flammability behavior of coconut shell and jackfruit skin powder-reinforced bio-composites fabricated through fused deposition modeling
Authors:
- Reddygari Meenakshi ReddyRRReddygari Meenakshi Reddy
- Subashini KasiviswanathanSKSubashini Kasiviswanathan
- Akhilesh Kumar SinghASAkhilesh Kumar Singh
- Donti Ratnam SrinivasanDSDonti Ratnam Srinivasan
- Shubhlakshmi TiwariSTShubhlakshmi Tiwari
- Shilpa Bhimrao SahareSSShilpa Bhimrao Sahare
- A. Joseph ArockiamAAA. Joseph Arockiam
- Surrya Prakash DillibabuSDSurrya Prakash Dillibabu
- Rengaiyah Govindarajan PadmanabhanRPRengaiyah Govindarajan Padmanabhan
- 23 May 2025
- journal article
- research article
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
Abstract
This study investigates the development of biodegradable bio-composites made from polylactic acid (PLA) reinforced with farm waste materials, specifically coconut shell powder and jackfruit skin powder. The bio-composite filaments were fabricated using a filament extruder, and the samples were created through fused deposition modeling (FDM). Mechanical strength, water absorption, and flammability were evaluated. The results revealed that incorporating coconut shell (CBC) and jackfruit skin (JBC) powders into the PLA matrix significantly enhanced the mechanical properties, water resistance, and flame retardancy of the composites. The hybrid bio-composite (HBC) showed a 73.7 % improvement in water absorption resistance, with a water absorption rate of 9.06 ± 0.02 %. CBC and JBC demonstrated 70.8 % and 67.2 % reductions in water absorption, respectively, compared to pure PLA. The HBC bio composite also exhibited superior flame retardancy, with a 60.9 % increase in ignition delay (8.43 ± 0.21 s), 30.5 % reduction in flame spread rate (43.21 ± 1.42 mm min−1), and 50.5 % increase in after-flame duration (13.14 ± 1.05 s). In terms of tensile properties, HBC outperformed all other composites with an ultimate tensile strength (UTS) of 59.2 ± 1.8 MPa, representing a 44.2 % improvement compared to pure PLA. The CBC and JBC showed 24.7 % and 10.7 % increases in UTS, respectively. The HBC also showed a 40.2 % improvement in flexural strength, with the lowest deflection at 4.0 ± 0.1 mm, compared to 23 % and 20.8 % improvements for CBC and JBC, respectively.Keywords
This publication has 40 references indexed in Scilit:
- A review on natural fiber composites: Polymer matrices, fiber surface treatments, fabrication methods, properties, and applicationsPolymer Engineering & Science, 2024
- Synthesis and suitability characterization of microcrystalline cellulose from Citrus x sinensis sweet orange peel fruit waste-based biomass for polymer composite applicationsJournal of Polymer Research, 2024
- Novel Ficus retusa L. aerial root fiber: a sustainable alternative for synthetic fibres in polymer composites reinforcementBiomass Conversion and Biorefinery, 2024
- An overview of fused filament fabrication technology and the advancement in PLA-biocompositesThe International Journal of Advanced Manufacturing Technology, 2024
- Flame retardant properties of biocomposites for aircraft applications2024
- Experimental and simulation study for mechanical properties characterisation of green natural reinforced compositesInternational Journal on Interactive Design and Manufacturing (IJIDeM), 2023
- A review of research and application of polylactic acid compositesJournal of Applied Polymer Science, 2022
- Bio-Composites Reinforced with Natural Fibers: Comparative Analysis of Thermal, Static and Dynamic-Mechanical PropertiesFibers and Polymers, 2020
- Influence of Montmorillonite Clay Content on Thermal, Mechanical, Water Absorption and Biodegradability Properties of Treated Kenaf Fiber/ PLA-Hybrid BiocompositesSilicon, 2020
- Effects of the infill pattern on mechanical properties of fused layer modeling (FLM) 3D printed wood/polylactic acid (PLA) compositesEuropean Journal of Wood and Wood Products, 2019