Shilpa Bhimrao Sahare
Research Subjects
Shilpa Bhimrao Sahare has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Akhilesh Kumar Singh
Department of Mechanical Engineering Aditya College of Engineering and Technology Surampalem Andhra Pradesh India
1 shared publication - Chetan Mahatme
Department of Mechanical Engineering, Yeshwantrao Chavan College of Engineering, Nagpur, India
1 shared publication - Donti Ratnam Srinivasan
Department of Mechanical Engineering JNTUA College of Engineering Anantapur India
1 shared publication - Emad Makki
Department of Mechanical Engineering, College of Engineering and Architecture, Umm Al-Qura University, Makkah, 24382, Saudi Arabia.
1 shared publication - Hitesh Panchal
Mechanical Engineering Department, Government Engineering College Patan, Katpur, India
1 shared publication - Jayant Giri
Department of Mechanical Engineering, Yeshwantrao Chavan College of Engineering, Nagpur, India
1 shared publication
Latest Publications
- 23 May 2025
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
Mechanical, water absorption, and flammability behavior of coconut shell and jackfruit skin powder-reinforced bio-composites fabricated through fused deposition modeling
This study investigates the development of biodegradable bio-composites made from polylactic acid (PLA) reinforced with farm waste materials, specifically coconut shell powder and jackfruit skin powder. The bio-composite filaments were fabricated using a filament extruder, and the samples were created through fused deposition modeling (FDM). Mechanical strength, water absorption, and flammability were evaluated. The results revealed that incorporating coconut shell (CBC) and jackfruit skin (JBC) powders into the PLA matrix significantly enhanced the mechanical properties, water resistance, and flame retardancy of the composites. The hybrid bio-composite (HBC) showed a 73.7 % improvement in water absorption resistance, with a water absorption rate of 9.06 ± 0.02 %. CBC and JBC demonstrated 70.8 % and 67.2 % reductions in water absorption, respectively, compared to pure PLA. The HBC bio composite also exhibited superior flame retardancy, with a 60.9 % increase in ignition delay (8.43 ± 0.21 s), 30.5 % reduction in flame spread rate (43.21 ± 1.42 mm min−1), and 50.5 % increase in after-flame duration (13.14 ± 1.05 s). In terms of tensile properties, HBC outperformed all other composites with an ultimate tensile strength (UTS) of 59.2 ± 1.8 MPa, representing a 44.2 % improvement compared to pure PLA. The CBC and JBC showed 24.7 % and 10.7 % increases in UTS, respectively. The HBC also showed a 40.2 % improvement in flexural strength, with the lowest deflection at 4.0 ± 0.1 mm, compared to 23 % and 20.8 % improvements for CBC and JBC, respectively.
- 23 May 2025
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
Mechanical, water absorption, and flammability behavior of coconut shell and jackfruit skin powder-reinforced bio-composites fabricated through fused deposition modeling
This study investigates the development of biodegradable bio-composites made from polylactic acid (PLA) reinforced with farm waste materials, specifically coconut shell powder and jackfruit skin powder. The bio-composite filaments were fabricated using a filament extruder, and the samples were created through fused deposition modeling (FDM). Mechanical strength, water absorption, and flammability were evaluated. The results revealed that incorporating coconut shell (CBC) and jackfruit skin (JBC) powders into the PLA matrix significantly enhanced the mechanical properties, water resistance, and flame retardancy of the composites. The hybrid bio-composite (HBC) showed a 73.7 % improvement in water absorption resistance, with a water absorption rate of 9.06 ± 0.02 %. CBC and JBC demonstrated 70.8 % and 67.2 % reductions in water absorption, respectively, compared to pure PLA. The HBC bio composite also exhibited superior flame retardancy, with a 60.9 % increase in ignition delay (8.43 ± 0.21 s), 30.5 % reduction in flame spread rate (43.21 ± 1.42 mm min−1), and 50.5 % increase in after-flame duration (13.14 ± 1.05 s). In terms of tensile properties, HBC outperformed all other composites with an ultimate tensile strength (UTS) of 59.2 ± 1.8 MPa, representing a 44.2 % improvement compared to pure PLA. The CBC and JBC showed 24.7 % and 10.7 % increases in UTS, respectively. The HBC also showed a 40.2 % improvement in flexural strength, with the lowest deflection at 4.0 ± 0.1 mm, compared to 23 % and 20.8 % improvements for CBC and JBC, respectively.
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (1)
An application of hybrid Taguchi-ANN to predict tool wear for turning EN24 material
This work is an attempt to predict tool wear for turning EN24 material by the hybrid Taguchi-ANN (Taguchi-Artificial Neural Network) method. The objective is to minimize the tool wear. The independent factors are cutting environment, feed rate, depth of cut, nose radius, and tool type. A Spinner numerical control lathe is used to assess performance. As per the Taguchi orthogonal array, 27 experiments are conducted for each value of the uncontrollable factor (spindle vibration). Optimal setting is structured by Taguchi analysis and the response table. The additive model is used to predict the response. Conformity test is carried out to check whether the predicted and experimental values of response are within the range given by the confidence interval. Furthermore, the ANN is used to predict and analyze the tool wear. The result showed that the supremely important parameter is depth of cut and the least important parameter is tool type. The ideal set found is A3, B3, C3, D1, and E3. Through ANN analysis, it is observed that the experimental values are very close to the predicted values of tool wear. The predicted value at optimal setting is 0.0401 mm. The experimental values at optimal setting is 0.0422 mm. In addition, the study showed that when the feed rate and nose radius are both set to high levels and the depth of cut is medium, using an uncoated tungsten carbide tool with minimal lubrication results in the least amount of tool wear.
- 1 January 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (1)
Open AccessAn application of hybrid Taguchi-ANN to predict tool wear for turning EN24 material
This work is an attempt to predict tool wear for turning EN24 material by the hybrid Taguchi-ANN (Taguchi-Artificial Neural Network) method. The objective is to minimize the tool wear. The independent factors are cutting environment, feed rate, depth of cut, nose radius, and tool type. A Spinner numerical control lathe is used to assess performance. As per the Taguchi orthogonal array, 27 experiments are conducted for each value of the uncontrollable factor (spindle vibration). Optimal setting is structured by Taguchi analysis and the response table. The additive model is used to predict the response. Conformity test is carried out to check whether the predicted and experimental values of response are within the range given by the confidence interval. Furthermore, the ANN is used to predict and analyze the tool wear. The result showed that the supremely important parameter is depth of cut and the least important parameter is tool type. The ideal set found is A3, B3, C3, D1, and E3. Through ANN analysis, it is observed that the experimental values are very close to the predicted values of tool wear. The predicted value at optimal setting is 0.0401 mm. The experimental values at optimal setting is 0.0422 mm. In addition, the study showed that when the feed rate and nose radius are both set to high levels and the depth of cut is medium, using an uncoated tungsten carbide tool with minimal lubrication results in the least amount of tool wear.