K/Ka-Band Hybrid-Packaged Four-Element Four-Beam Phased-Array Transmitter and Receiver Front-Ends With Optimized Beamforming Passive Networks
Top Cited Papers
- 30 April 2024
- journal article
- research article
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (10) , 3142-3155
Abstract
This article presents K/Ka-band four-element four-beam phased-array transmitter (TX) and receiver (RX) front-ends. Hybrid-packaged technology is employed, consisting of one TX/RX 65-nm CMOS beamformer and four 0.1- $\mu$ m GaAs power amplifiers (PAs)/low-noise amplifiers (LNAs). Each beam maintains a full connection to every antenna element without degrading array gain. A compact and symmetrical layout floor-plan is proposed to reduce signal routing complexity. Signal distribution and combination are performed through two optimized tree-type and rectangular-shaped beamforming networks to improve the beam-to-beam consistency and isolation. The TX/RX CMOS beamformer provides an energy-efficient solution by adopting low-power phase/amplitude controls. The second harmonic trap is co-optimized with the transformer-based matching to enhance linearity in the TX. A new L-type inductor-enhanced matching network is devised in the RX to broaden bandwidth. In addition, the digital circuit introduces a voting mechanism to improve fault tolerance. Utilizing fan-out wafer-level chip-scale packaging, both hybrid-packaged TX and RX front-ends occupy an area of 50 mm $^\text{2}$ . The proposed TX demonstrates a measured small-signal gain of 23.5–26.5 dB across 17.7–20.2 GHz. The output 1-dB compression point ( $P_\text{1\,dB}$ ) and the maximal power-added efficiency (PAE $_\text{MAX}$ ) reach 21.2–23.2 dBm and 26%–30%, respectively. The proposed RX achieves a measured average gain of 24 dB across 27.5–30 GHz with a minimal noise figure (NF) of 3.1 dB. Both TX and RX exhibit uniform performance across all channels, while consuming a maximal power of 2600 and 264 mW, respectively, equivalent to 162.5–16.5 mW per element per beam.Keywords
Funding Information
- Major Key Project of Peng Cheng Laboratory, Shenzhen, China
This publication has 36 references indexed in Scilit:
- A 71-to-86-GHz 16-Element by 16-Beam Multi-User Beamforming Integrated Receiver Sub-Array for Massive MIMOIEEE Journal of Solid-State Circuits, 2021
- Dual-Band, Two-Layer Millimeter-Wave Transceiver for Hybrid MIMO SystemsIEEE Journal of Solid-State Circuits, 2021
- A Ka-Band SATCOM Transceiver in 65-nm CMOS With High-Linearity TX and Dual-Channel Wide-Dynamic-Range RX for Terrestrial TerminalIEEE Journal of Solid-State Circuits, 2021
- A 28-GHz Beam-Space MIMO RX With Spatial Filtering and Frequency-Division Multiplexing-Based Single-Wire IF InterfaceIEEE Journal of Solid-State Circuits, 2020
- Power-Efficient Design Techniques for mm-Wave Hybrid/Digital FDD/Full-Duplex MIMO TransceiversIEEE Journal of Solid-State Circuits, 2020
- Secure Satellite Communication Digital IF CMOS $Q$ -Band Transmitter and $K$ -Band ReceiverIEEE Journal of Solid-State Circuits, 2019
- Design and Analysis of a Low Loss, Wideband Digital Step Attenuator With Minimized Amplitude and Phase VariationsIEEE Journal of Solid-State Circuits, 2018
- A 25–30 GHz Fully-Connected Hybrid Beamforming Receiver for MIMO CommunicationIEEE Journal of Solid-State Circuits, 2018
- A 16-Element 4-Beam 1 GHz IF 100 MHz Bandwidth Interleaved Bit Stream Digital Beamformer in 40 nm CMOSIEEE Journal of Solid-State Circuits, 2018
- A 28-GHz Phased-Array Receiver Front End With Dual-Vector Distributed BeamformingIEEE Journal of Solid-State Circuits, 2016