Experimental investigation of electrochemical machining performance of AISI 304 stainless steel using a palladium-coated electrode with ascorbic acid - mixed electrolyte
Authors:
- Nethaji Subash Chandra Bose AyyavooNANethaji Subash Chandra Bose Ayyavoo
- Saravanan Kandasamy GanesanSGSaravanan Kandasamy Ganesan
- Thirunavukkarasu RajaTRThirunavukkarasu Raja
- Vinod Kumaar Jeevarathnam Ravi KumarVKVinod Kumaar Jeevarathnam Ravi Kumar
- Lakshmanan SankaralingamLSLakshmanan Sankaralingam
- Kumar SubramanianKSKumar Subramanian
- Karthikeyan SaminathanKSKarthikeyan Saminathan
- Thangavel ThirugnanasambandhamTTThangavel Thirugnanasambandham
Open Access
- 14 November 2026
- journal article
- Published by International Association of Physical Chemists (IAPC) in Journal of Electrochemical Science and Engineering
- Vol. 16
Abstract
Passive film generation, buildup of insoluble hydroxide sludge, and dimensional errors caused by uncontrolled anodic dissolution are issues that arise during electrochemical machining (ECM) of AISI 304 stainless steel (SS). While electrode coatings and electrolyte additives have been studied separately, the combination of palladium (Pd)-coated electrodes and ascorbic acid-modified electrolytes to enhance ECM performance has received less attention. Using a Pd-coated needle electrode and a sodium nitrate (NaNO3) electrolyte containing 10 g L-1 ascorbic acid, this study experimentally analyses the machining properties of AISI 304 SS. The effects on machining rate (MR) and overcut (OC) of electrolyte concentration (0.328 to 0.386 mol L-2), machining voltage (7 to 12 V), duty cycle (40 to 90 %), and pulse frequency (40 to 90 Hz) were methodically assessed. The machined-hole shape was examined using scanning electron microscopy (SEM), and the electrode substrate was characterized using energy-dispersive X-ray spectroscopy. Experimental data show that increasing electrolyte concentration, machining voltage, duty cycle, and pulse frequency enhanced MR and decreased OC within the examined ranges. With a 58.4 % improvement in MR from 0.219 to 0.347 μm s-1 and a 23.4 % decrease in OC from 290 to 222 μm when frequency increased from 40 to 90 Hz, pulse frequency showed the greatest increase in MR. At an electrolyte concentration of 0.386 mol L-1, a machining voltage of 12 V, a 90 % duty cycle, and a pulse frequency of 90 Hz, the maximum recorded MR of 0.347 μm s-1 with an OC of 222 μm was attained. Nearly circular machined holes with comparatively clean edges and few surface deposits were visible in SEM examinations, suggesting regulated anodic dissolution. By reducing Fe3+ to Fe2+, ascorbic acid is suggested to prevent the formation of insoluble ferric hydroxide, promoting electrolyte stability and eliminating reaction products. Using a Pd-coated electrode and an electrolyte modified with ascorbic acid, the study determines an experimentally assessed processing window for ECM of AISI 304 stainless steel, offering insights into increasing machining productivity and dimensional correctness.Keywords
This publication has 25 references indexed in Scilit:
- Investigation of electrochemical micromachining on magnesium alloy using hollow tool electrodeUltrasonics, 2024
- Optimizing coverage of palladium nanoparticles for a highly sensitive hydrogen gas sensor based on nanogaps via spray-depositionJournal of Materials Science: Materials in Electronics, 2024
- Experimental investigation on the suitability of dual fluid system-assisted ECM (DF-ECM) and the influence of magnet in machining of SS304The International Journal of Advanced Manufacturing Technology, 2024
- Preparation of sidewall-insulation layer on micro-hollow electrodes for ECM by asymmetric-timed bipolar electrophoretic coating method and its applicationPrecision Engineering, 2021
- Characteristics research of different electrode tip shapes by electrodeposition for micro slot ECMProcedia CIRP, 2020
- Electrode insulation layer for electrochemical machining fabricated through hot-dip aluminizing and microarc oxidation on a stainless-steel substrateSurface and Coatings Technology, 2019
- Silicon-based tool electrodes for micro electrochemical machiningPrecision Engineering, 2018
- Selection and Optimization of Electrolyte for Micro Electrochemical Machining on Stainless Steel 304Procedia CIRP, 2016
- Development of Helical Electrode Insulation Layer for Electrochemical MicrodrillingProcedia CIRP, 2013
- Use of coated microtools in advanced manufacturing: An exploratory study in electrochemical machining (ECM) contextJournal of Manufacturing Processes, 2012