Kumar Subramanian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kumar Subramanian has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Dhanesh G. Mohan
University of Sunderland
2 shared publications - Jacek Tomków
Institute of Manufacturing and Materials Technology, Faculty of Mechanical Engineering and Ship Technology, Gdańsk University of Technology, 80-233 Gdańsk, Poland
1 shared publication K Nivethan
1 shared publication- Karthikeyan Saminathan
Erode Sengunthar Engineering College
1 shared publication - Kumaar Jeevarathnam Ravi Kumar Vinod
Department of Mechanical Engineering, Dr. N. G. P. Institute of Technology, Coimbatore, 641048, India
1 shared publication - Lakshmanan Sankaralingam
Department of Aeronautical Engineering, Dayananda Sagar College of Engineering, Bangalore 560078, India
1 shared publication
Latest Publications
- Open Access
- 14 November 2026
- Published by International Association of Physical Chemists (IAPC) in Journal of Electrochemical Science and Engineering
- Vol. 16
Experimental investigation of electrochemical machining performance of AISI 304 stainless steel using a palladium-coated electrode with ascorbic acid - mixed electrolyte
Passive film generation, buildup of insoluble hydroxide sludge, and dimensional errors caused by uncontrolled anodic dissolution are issues that arise during electrochemical machining (ECM) of AISI 304 stainless steel (SS). While electrode coatings and electrolyte additives have been studied separately, the combination of palladium (Pd)-coated electrodes and ascorbic acid-modified electrolytes to enhance ECM performance has received less attention. Using a Pd-coated needle electrode and a sodium nitrate (NaNO3) electrolyte containing 10 g L-1 ascorbic acid, this study experimentally analyses the machining properties of AISI 304 SS. The effects on machining rate (MR) and overcut (OC) of electrolyte concentration (0.328 to 0.386 mol L-2), machining voltage (7 to 12 V), duty cycle (40 to 90 %), and pulse frequency (40 to 90 Hz) were methodically assessed. The machined-hole shape was examined using scanning electron microscopy (SEM), and the electrode substrate was characterized using energy-dispersive X-ray spectroscopy. Experimental data show that increasing electrolyte concentration, machining voltage, duty cycle, and pulse frequency enhanced MR and decreased OC within the examined ranges. With a 58.4 % improvement in MR from 0.219 to 0.347 μm s-1 and a 23.4 % decrease in OC from 290 to 222 μm when frequency increased from 40 to 90 Hz, pulse frequency showed the greatest increase in MR. At an electrolyte concentration of 0.386 mol L-1, a machining voltage of 12 V, a 90 % duty cycle, and a pulse frequency of 90 Hz, the maximum recorded MR of 0.347 μm s-1 with an OC of 222 μm was attained. Nearly circular machined holes with comparatively clean edges and few surface deposits were visible in SEM examinations, suggesting regulated anodic dissolution. By reducing Fe3+ to Fe2+, ascorbic acid is suggested to prevent the formation of insoluble ferric hydroxide, promoting electrolyte stability and eliminating reaction products. Using a Pd-coated electrode and an electrolyte modified with ascorbic acid, the study determines an experimentally assessed processing window for ECM of AISI 304 stainless steel, offering insights into increasing machining productivity and dimensional correctness.
- 14 November 2026
- Published by International Association of Physical Chemists (IAPC) in Journal of Electrochemical Science and Engineering
- Vol. 16
Open AccessExperimental investigation of electrochemical machining performance of AISI 304 stainless steel using a palladium-coated electrode with ascorbic acid - mixed electrolyte
Passive film generation, buildup of insoluble hydroxide sludge, and dimensional errors caused by uncontrolled anodic dissolution are issues that arise during electrochemical machining (ECM) of AISI 304 stainless steel (SS). While electrode coatings and electrolyte additives have been studied separately, the combination of palladium (Pd)-coated electrodes and ascorbic acid-modified electrolytes to enhance ECM performance has received less attention. Using a Pd-coated needle electrode and a sodium nitrate (NaNO3) electrolyte containing 10 g L-1 ascorbic acid, this study experimentally analyses the machining properties of AISI 304 SS. The effects on machining rate (MR) and overcut (OC) of electrolyte concentration (0.328 to 0.386 mol L-2), machining voltage (7 to 12 V), duty cycle (40 to 90 %), and pulse frequency (40 to 90 Hz) were methodically assessed. The machined-hole shape was examined using scanning electron microscopy (SEM), and the electrode substrate was characterized using energy-dispersive X-ray spectroscopy. Experimental data show that increasing electrolyte concentration, machining voltage, duty cycle, and pulse frequency enhanced MR and decreased OC within the examined ranges. With a 58.4 % improvement in MR from 0.219 to 0.347 μm s-1 and a 23.4 % decrease in OC from 290 to 222 μm when frequency increased from 40 to 90 Hz, pulse frequency showed the greatest increase in MR. At an electrolyte concentration of 0.386 mol L-1, a machining voltage of 12 V, a 90 % duty cycle, and a pulse frequency of 90 Hz, the maximum recorded MR of 0.347 μm s-1 with an OC of 222 μm was attained. Nearly circular machined holes with comparatively clean edges and few surface deposits were visible in SEM examinations, suggesting regulated anodic dissolution. By reducing Fe3+ to Fe2+, ascorbic acid is suggested to prevent the formation of insoluble ferric hydroxide, promoting electrolyte stability and eliminating reaction products. Using a Pd-coated electrode and an electrolyte modified with ascorbic acid, the study determines an experimentally assessed processing window for ECM of AISI 304 stainless steel, offering insights into increasing machining productivity and dimensional correctness.
- Open Access
- 1 January 2024
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2024 (1)
Study on Machinability Behaviour and Simultaneous Optimisation of Multiple Responses Using Taguchi‐Based Grey Relational Analysis in End Milling of Aluminum Hybrid Composites
The present work reveals the machinability characteristics of Al7068/Si3N4/BN hybrid composite materials. The composite materials were prepared through the liquid metallurgy technique with various weight fractions (0, 5, 10) of silicon nitride and hexagonal boron nitride particles. The experimental studies were performed on a CNC milling machine by varying cutting speed (600, 1200 and 1800 rpm), feed rate (150, 300 and 450 mm/min), and depth of cut (0.8, 1.2 and 1.6 mm). Taguchi’s plan of experiments (L27 orthogonal array design) and analysis of variance (ANOVA) were employed to investigate the effect of process parameters on surface roughness (Ra), cutting temperature, and material removal rate (MRR). Taguchi‐based grey relational analysis (GRA) was performed to identify the best process parameters combination for optimising the multiple responses simultaneously. ANOVA results revealed that the weight fraction of Si3N4 is the most contributing parameter for multiple response characteristics.
- 1 January 2024
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2024 (1)
Open AccessStudy on Machinability Behaviour and Simultaneous Optimisation of Multiple Responses Using Taguchi‐Based Grey Relational Analysis in End Milling of Aluminum Hybrid Composites
The present work reveals the machinability characteristics of Al7068/Si3N4/BN hybrid composite materials. The composite materials were prepared through the liquid metallurgy technique with various weight fractions (0, 5, 10) of silicon nitride and hexagonal boron nitride particles. The experimental studies were performed on a CNC milling machine by varying cutting speed (600, 1200 and 1800 rpm), feed rate (150, 300 and 450 mm/min), and depth of cut (0.8, 1.2 and 1.6 mm). Taguchi’s plan of experiments (L27 orthogonal array design) and analysis of variance (ANOVA) were employed to investigate the effect of process parameters on surface roughness (Ra), cutting temperature, and material removal rate (MRR). Taguchi‐based grey relational analysis (GRA) was performed to identify the best process parameters combination for optimising the multiple responses simultaneously. ANOVA results revealed that the weight fraction of Si3N4 is the most contributing parameter for multiple response characteristics.
- Open Access
Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites
Hybrid aluminium metal matrix composites have the potential to replace single reinforced aluminium metal matrix composites due to improved properties. Moreover, tribological performance is critical for these composites, as they have extensive application areas, such as the automotive, aerospace, marine and defence industries. The present work aims to establish the tribological characteristics of Al7068/Si3N4/BN hybrid metal matrix composites prepared by stir casting route and studied using a pin-on-disc apparatus under dry sliding conditions. The hybrid composite samples were prepared at various weight percentages (0, 5, 10) of Si3N4 and BN particles. To investigate the tribological performance of the prepared composites, the wear experiments were conducted by varying the load (20, 40 and 60 N), sliding velocity (1.5, 2.5 and 3.5 m/s) and sliding distance (500, 1000 and 1500 m). Wear experimental runs were carried out based on the plan of experiments proposed by Taguchi. The minimum wear rate was found with the composite material reinforced with 10 wt. % of Si3N4 and 5 wt. % of BN. Analysis of Variance (ANOVA) was employed to analyse the effect of process parameters on wear rate and coefficient of friction (COF). The ANOVA test revealed that the weight fraction of Si3N4 has more of a contribution percentage (36.60%) on wear rate, and load has more of a contribution percentage (29.73%) on COF. The worn-out surface of the wear test specimens was studied using its corresponding SEM micrograph and correlated with the dry sliding wear experiment results.
Open AccessStudy on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites
Hybrid aluminium metal matrix composites have the potential to replace single reinforced aluminium metal matrix composites due to improved properties. Moreover, tribological performance is critical for these composites, as they have extensive application areas, such as the automotive, aerospace, marine and defence industries. The present work aims to establish the tribological characteristics of Al7068/Si3N4/BN hybrid metal matrix composites prepared by stir casting route and studied using a pin-on-disc apparatus under dry sliding conditions. The hybrid composite samples were prepared at various weight percentages (0, 5, 10) of Si3N4 and BN particles. To investigate the tribological performance of the prepared composites, the wear experiments were conducted by varying the load (20, 40 and 60 N), sliding velocity (1.5, 2.5 and 3.5 m/s) and sliding distance (500, 1000 and 1500 m). Wear experimental runs were carried out based on the plan of experiments proposed by Taguchi. The minimum wear rate was found with the composite material reinforced with 10 wt. % of Si3N4 and 5 wt. % of BN. Analysis of Variance (ANOVA) was employed to analyse the effect of process parameters on wear rate and coefficient of friction (COF). The ANOVA test revealed that the weight fraction of Si3N4 has more of a contribution percentage (36.60%) on wear rate, and load has more of a contribution percentage (29.73%) on COF. The worn-out surface of the wear test specimens was studied using its corresponding SEM micrograph and correlated with the dry sliding wear experiment results.
- 6 March 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (6) , 066502
Two body abrasive wear characteristics of Al7068/Si3N4/BN hybrid composite
- 6 March 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (6) , 066502
Two body abrasive wear characteristics of Al7068/Si3N4/BN hybrid composite