Surface and Tribological Properties of Powder Metallurgical Cp-Ti Titanium Alloy Modified by Shot Peening
Authors:
- Yasemin Yıldıran AvcuYasemin Yıldıran Avcu
- Eleftherios IakovakisEIEleftherios Iakovakis
- Mert GuneyMert Guney
- Emirhan ÇalımEÇEmirhan Çalım
- Ayşe ÖzkılınçAÖAyşe Özkılınç
- Eray AbakayEAEray Abakay
- Fikret SönmezFSFikret Sönmez
- Funda Gül KoçFKFunda Gül Koç
- Rıdvan YamanoğluRYRıdvan Yamanoğlu
- Abdulkadir CengizACAbdulkadir Cengiz
- Egemen AvcuEgemen Avcu
Open Access
Abstract
The present study reveals for the first time the dry sliding wear behavior of a powder metallurgical pure titanium alloy (Cp-Ti) modified by shot peening. Cp-Ti samples were manufactured via powder metallurgy, and then their surface and subsurface features were modified using a custom-made, fully automated shot-peening system. The texture isotropy rate and the highest orientation angle of the shot-peened samples were 71.5% and 36°, respectively. The Abbott curves of the shot-peened surfaces revealed that the most common areal roughness value was 5.177 μm, with a frequency of 8.1%. Shot-peened surfaces exhibited an ~20% lower wear rate than unpeened surfaces under dry sliding wear, whereas the coefficient of friction was the same for both surfaces. Micro-ploughing, micro-cutting, oxidation, and three-body abrasion wear mechanisms were observed on the shot-peened and unpeened surfaces. High resolution 3D surface topographies of worn unpeened and shot-peened surfaces revealed micro-scratches and inhomogeneities along wear tracks, which are indicative of three-body abrasion mechanisms during contact. In addition, vertical and horizontal microcracks were visible just beneath the wear track, suggesting a clear indication of plastic deformation during contact. The cross-sectional hardness maps of shot-peened samples revealed the formation of a work-hardened surface layer with shot peening, which improved the wear resistance. These findings support that shot peening can be a useful tool to modify the surface and tribological properties of powder metallurgical Cp-Ti alloys.Keywords
Funding Information
- Kocaeli University Scientific Research Projects Coordination Unit (2503)
This publication has 39 references indexed in Scilit:
- Dry Sliding Wear Behaviour of Shot Peened TI6AL4V Alloys at Different Peening TimesActa Physica Polonica A, 2018
- Improvement in tribological behavior of commercial pure titanium (CP-Ti) by surface mechanical attrition treatment (SMAT)Tribology International, 2018
- Effect of shot-peening on the fretting wear and crack initiation behavior of Ti-6Al-4V dovetail joint specimensInternational Journal of Fatigue, 2018
- Iterative mesh-based hardness mappingScience and Technology of Welding and Joining, 2017
- The effect of vibratory and rotational shot peening and wear on fatigue life of steelEksploatacja i Niezawodność – Maintenance and Reliability, 2016
- Effects of shot peening pressure, media type and double shot peening on the microstructure, mechanical and tribological properties of low-alloy steelSurface Topography: Metrology and Properties, 2016
- Study on improved tribological properties by alloying copper to CP-Ti and Ti–6Al–4V alloyMaterials Science and Engineering: C, 2015
- Unlubricated sliding friction and wear characteristics of thermally oxidized commercially pure titaniumWear, 2013
- Experimental Investigation on Microstructure and Mechanical Properties of Nd:YAG Laser Treated CP-Ti and & Ni-Cr Alloys for Dental ApplicationsProcedia Engineering, 2013
- The genesis of frictionWear, 1981